Jarvis COMPLIFT LIGHT DUTY 1 Bedienungsanleitung
LIGHT DUTY #1 COMPLIFT
INSTRUCTION MANUAL
COMPLIFT
1-800-548-4239
A division of Jarvis Industries, Inc.
One Year Guarantee
Every JARVIS product is inspected before leaving the factory. This product is warranted to be
free of defects in material and workmanship. JARVISwill replace free of charge, with the same
or like item of equal value any item found to have defects in materials or workmanship during
the first 1 year of customer ownership with proof of purchase. Proof of purchase must be either
original or clear copy of your receipt. Call 1-800-548-4239 for a return authorization number.
This warranty gives you specific legal rights and you may also have other rights which may
vary from state to state. Some parts made in China.
LIFT MAINTENANCE
No maintenance is required other than inspection for safety.
Owner and/or Operator Responsibility
The owner and/or operator shall study the product instructions and retain them for
future reference.
Operation
The owner and/or operator shall have an understanding of the product and safety
operating instructions before operating the LIFT. Safety information shall be
emphasized and understood. If the operator is not fluent in English, the product and
safety instructions shall be read to and discussed with the operator in the operator’s
native language by the purchaser/owner or his designee, making sure that the operator
comprehends their contents.
Maintenance
The LIFT shall be maintained inthe accordance with the product instructions.
Inspection
(a) Visual inspection shall be made before each use of the LIFT by checking for
abnormal conditions, such as cracked welds, leaks, and damaged, loose, or
missing parts.
(b) Other inspections shall be made per product operating instructions.
(c) Each LIFT shall be inspected immediately if the lift is believed to have been
subjected to an abnormal load or shock. It is recommended that this inspection be
made by a manufacturer’s or supplier’s authorized repair factility.
(d) Owners and/or operators should be aware that repair of this equipment may
require specialized knowledge and facilities. It is recommended that an annual
inspection of the LIFT be made by a manufacturer’s or supplier’s authorized repair
facility and that any defective parts, decals, or safety labels or signs be replaced with
maufacturer’s or supplier’s specified parts.
Damaged Equipment
Any LIFT that appears to be damaged in any way, is found to be worn or operates
abnormally SHALL BE REMOVED FROM SERVICE UNTIL REPAIRED. It is
recommended that necessary repairs be made by a manufacturer’s or supplier’s
authorized repair facility if repairs are permitted by the manufacturer or supplier.
2.
Alterations
Because of potential hazards associated with this type of equipment, no alterations
shall be made to the products.
Attachments and Adaptors
Only attachments and/or adaptors supplied by the manufacturer shall be used.
3.
- Study, understand, and follow all instructions before operating this device.
-This is a lifting device only.
- Do not exceed rated capacity.
- Use 3/4” plywood for soft surfaces.
- Failure to heed these markings may result in personal injury and/or property damage.
- No alterations to the LIFT shall be made to this product.
WARNING
!
INSTRUCTIONS FOR USE
Set up can be easily completed by one person. Assembly of the lift can be accomplished
with the pieces laying horizontially on the ground.
1. Assemble the two telescoping leg assm. using the two spring hitch pins. Set for maximum
height. Height can be easily adjusted after the lift is set up. Orientation of pieces are optional.
2. Slide the trolley assemblyon the beam. Note orientation.
3. Insert the beam in to legassemblies. Pins must be installed for safety.
4. Lift up assembly. Position lift so that space is provided to allow compressor to be lowered
to the ground. NOTE : Chain hoist can be installedbefore or after lift is set up.
NOTE : Remove all connections & fasteners of compressor at any step before Step 5.
5. Install the small lift on the compressor. Position the lifting ring so that it is slightly off
center, away from thelifting ring on the compressor.
6. Install the chain hoist hook onto the lifting ring.
7. Compressor can now be lifted and removed.
CHAIN HOIST
LEG
ASSM.
BEAM
SPRING
HITCH
PIN
TROLLEY
SPRING
HITCH
PIN
LEG
ASSM.
Spread leg assemblies
for increased stability.
SPRING
HITCH
PIN
SPRING
HITCH
PIN
Andere Jarvis Hebesystem Handbücher
Beliebte Hebesystem Handbücher anderer Marken
morse
morse 82H-124 Bedienungsanleitung
Braun
Braun NL955 Series Bedienungsanleitung
haacon
haacon 1889.10 Bedienungsanleitung
Protekt
Protekt AT 252 Bedienungsanleitung
R. Beck Maschinenbau
R. Beck Maschinenbau HS 600 Bedienungsanleitung
Nova Technology International, LLC
Nova Technology International, LLC NAS Series Bedienungsanleitung
Genie
Genie Z-60/34 Bedienungsanleitung
Screen Technics
Screen Technics INTERFIT Vertical Up Lift Bedienungsanleitung
Mortuary Lift
Mortuary Lift ULTIMATE 1000 Bedienungsanleitung
Custom Equipment
Custom Equipment Hy-Brid 3 Series Programmierhandbuch
Custom Equipment
Custom Equipment Hy-Brid Lifts 2 Series Programmierhandbuch
Hy-Brid Lifts
Hy-Brid Lifts HB-P3.6 Programmierhandbuch
