Jaycar Electronics MB3752 Bedienungsanleitung

24V HEAVY DUTY

JUMP STARTER/ POWER BANK

MB3752

Storage

Specifications

Warning! When not in use store your instruction manual and product in a

safe and dry place.

Before re-use after storage it is recommended that the product is checked by

a suitably qualified person to eliminate the risk of fire or electric shock

Examine the product frequently for signs of wear or damage.

Built-in battery capacity 25.9V/ 3300mAh（85.47Wh）

Starting outlet voltage 24V

Starting outlet maximum 400A

DC outlet output voltage 12V/3.5A

19V/3.5A

USB outlet output voltage 5V/2.1A(Max)

Charging input voltage 12V/2A

Charging time ~5-6 h

Torch power 3W

Working temperature -20 C — 60 C

Storage temperature -20 C — 60 C

Distributed by:

Techbrands by Electus Distribution Pty Ltd.

320 Victoria Road, Rydalmere

NSW 2116 Australia

Ph: 1300 738 555

Int’l: +61 2 88323200

Fax 1300 738 500

www.techbrands.com

SAFETY & MAINTAINANCE

IMPORTANT SAFETY INSTRUCTIONS

1. SAVE THESE INSTRUCTIONS - This manual contains important safety

and operating instructions for this Jump Starter/ Power Bank.

2. Before using it, read all instructions and cautionary markings on the

product and in this instruction manual.

3. CAUTION - To reduce risk of injury, charge only with AC adaptor and

charging cord supplied. Other chargers may cause battery to burst causing

injury to persons and damage.

4. Do not expose product or chargers to rain, moisture, or snow.

5. Use of an attachment not recommended or sold by the manufacturer may

result in a risk of fire, electric shock, or injury to persons.

6. Make sure cord is located properly so that it will not be stepped on,

tripped over, or otherwise subjected to damage or stress.

7. Do not operate charger with damaged cord.

8. Do not operate the product or charger if it has received a sharp blow,

been dropped or otherwise damaged in any way; take it to a qualified

service person.

9. Do not disassemble product or charger; take it to a qualified service

person when service or repair is required. Incorrect reassembly may result in

a risk of electric shock or fire.

10. To reduce risk of electric shock, unplug charger before attempting any

maintenance or cleaning. Turning off controls will not reduce this risk.

11. The product is intended to be correctly orientated in a vertical or floor

position.

12. WARNING - RISK OF EXPLOSIVE GASES

a) BATTERIES GENERATE EXPLOSIVE GASES DURING NORMAL

BATTERY OPERATION. FOR THIS REASON, IT IS OF UTMOST

IMPORTANCE THAT EACH TIME BEFORE USING YOUR PRODUCT,

YOU READ THIS MANUAL AND FOLLOW THE INSTRUCTIONS

EXACTLY.

b) To reduce risk of battery explosion, follow these instructions and those

published by vehicle or battery manufacturer and manufacturer of any

equipment you intend to use in vicinity of battery. Review cautionary

How to Charge the Product

Charging on Vehicle:

Insert the DC adapter in the vehicle cigar lighter. Connect the DC head into

DC input port of the product. A scroll bar can be viewed on LCD display, i.e.

the product is being charged. After the charging is completed, the scroll bar

stops scrolling and display the battery is full.

Figure 8 Charging Diagrammatic Sketch

Charging at Home:

Select 12V 2A adapter to connect with the main supply socket. Connect the

DC output end into the DC socket of the product. A scroll bar can be viewed

on LCD display. After the charging is completed, the scroll bar stops scrolling

and display the battery is full.

110

Power Output Function with Multi-level Voltage Regulating

13. PERSONAL PRECAUTIONS

14. WARNING - FOLLOW THESE STEPS WHEN BOOSTING A BATTERY.

A SPARK NEAR BATTERY MAY CAUSE BATTERY EXPLOSION. TO

REDUCE RISK OF A SPARK NEAR BATTERY OR INJURY, FOLLOW

PRECAUTIONS BELOW.

a) Someone should be within range of your voice or close enough to

come to your aid when you work on your product

b) Have plenty of fresh water and soap nearby in case you need to clean

your skin, clothing, or eyes.

c) Wear complete eye protection and clothing protection. Avoid touching

eyes while working near battery.

d) If battery acid contacts skin or clothing, wash immediately with soap

and water. If acid enters eye, immediately flood eye with running cold

water for at least 10 minutes and get medical attention immediately.

e) NEVER smoke or allow a spark or flame in vicinity of battery or

engine.

f)Be extra cautious to reduce risk of dropping a metal tool onto battery.

It might spark or short-circuit battery or other electrical part that may

cause explosion.

g) Remove personal metal items such as rings, bracelets, necklaces,

and watches when working with a lead-acid battery. A lead-acid battery

can produce a short-circuit current high enough to weld a ring or the like

to metal, causing a severe burn.

h) Use your product on a 24 volt battery only. Do not connect to any

other volt battery system.

i) NEVER boost a frozen battery

j) This system is not designed to be used as a replacement for a

vehicular battery. Do not attempt to operate a vehicle or boat that does

not have a battery installed.

marking on these products and on engine.

c) DO NOT EXPOSE YOUR PRODUCT TO FIRE OR INTENSE HEAT

AS IT MAY EXPLODE.

a) Boosting procedures should only be performed in a safe, dry,

well-ventilated area.

b) When using this unit in proximity to the vehicle's battery and engine,

Figure 7 Multi-level Voltage Regulation Mobile Power Output

ON/OFF and Mode Switching: Press “ /DC SELECT” to start mobile

power function. After the equipment is started, press /DC SELECT key,

and DC output voltage can be switched between 12 V and 19V. After

pressing “DIM/ENTER” key to confirm, the voltage character stops flashing,

and DC outlet outputs corresponding voltage. Press /DC SELECT key for

at least 3 seconds to turn off the equipment.

DC Output Selection: Check external charging input parameters and

regulate the voltage output of the product. By using the cables and adapters,

it can achieve power supplying for the external equipments with different

voltage requirements such as laptop and other devices. If your equipment

does not work, please check whether the charging parameters of your

equipment are compliance with the output requirements of the product.

USB Output: USB output is standard 5V/2.1A current. USB output can

charge standard USB equipments. Please use the sold USB data wire to

charge your equipment.

Notes:

Connection sequences of adapter:

●Switch on the machine Switching voltage to external equipment

required level

●Insert DC adapter into the DC socket of the product

●Connect the adapter of corresponding product at the end of DC wire

●Insert the adapter into external equipment

●Check whether the charging is started on the external equipment

FIRST AID:

SKIN: If battery acid comes in contact with skin, rinse immediately with

running water, then wash thoroughly with soap and water. If redness, pain or

irritation occurs, seek immediate medical attention.

EYES: If battery acid comes in contact with eyes, flush eyes immediately -

for minimum of 10 minutes - seek immediate medical attention.

Recharge every 3 months when not in use in order to extend the life of

lithium batteries.

stand the unit on a flat, stable surface, and be sure to keep all clamps,

cords, and clothing and body parts away from moving vehicle compo-

nents.

c) Check polarity of battery posts. POSITIVE(POS, P,+) battery post

usually has larger diameter than NEGATIVE (NEG, N, -) post.

d) Determine which post of battery is grounded (connected) to the

chassis.

e) When disconnecting cables, disconnect clamp from vehicle chassis

first and then remove clip from battery terminal.

F) Store in a cool, dry place. Keep out of reach of children.

a) Vehicles that have on-board computerized systems may be damaged

if vehicle battery is boosted. Before boosting a vehicle battery, read the

vehicle's owner’s manual to confirm that external-starting assistance is

advised.

b) Excessive engine cranking can damage a vehicle's starter motor. If the

engine fails to start after the recommended number of attempts,

discontinue jump-start procedures and look for other problems that may

need to be corrected.

15. CAUTIONS -

Warning:

When the product does not identify the ignition of a truck, it will be switched

off automatically within 60s, or you can long press “ /DC SELECT ” key to

switch off the product.

When the truck cannot activate the product automatically due to low voltage

of battery or other causes, the product has manual activation mode setting.

Press “ /DC SELECT” and side plate LED warning light switch key “ ”

at the same time ( for at least 3 seconds), the product is activated manually.

The product can be used to start the truck directly.

When manual mode is used, the product does not have

reverse protection connection function. Do NOT connect

reversely under this mode.

Precautions:

The product can only be used as an emergency power for 24V truck

starting, and cannot replace the truck battery.

Please connect the output line alligator clips with battery based on

corresponding color.

When the voltage of built-in battery of the product is lower than the truck

starting required min voltage, the product will not output current to the truck

to start the engine.

When the voltage of truck battery is lower than 18V, the product will not

enter into start status automatically.

After the output line of the equipment is disconnected with the truck battery,

do not contact the positive pole and negative pole. It may generate result in

potential safety hazard.

The product can only be operated in the range of -20℃to 60℃.

Please match with your vehicle exhaust and select corresponding product

when buying this series of products.

This product has been carefully engineered and manufactured to give you

dependable operation. Please read this manual thoroughly before operating

your new product as it contains the information you need to become familiar

with its features and obtain the performance that will bring you continued

enjoyment for many years. Please keep this manual on file for future

reference.

Operation

Product Description

Figure 1 Product Front and Side Appearance Description

1. Torch ON/OFF

2. Torch

3. Display

4.ON/OFF/DC SELECT

5. DIM/ENTER

6. USB Output

7. DC12/19V Output

8. DC Input

9. LED Warning light

10. EC5 Output（24V output）

11. LED Warning light ON/OFF

MO DE B AC K LI GH T

/ DC S E LE C T D IM/EN TE R

MO DE B AC K LI GH T

2 3 4 56 7 8 9 1011

Display Description

1. Battery power capacity

2. Jump starter indicator

3. Charge indicator

4. USB output indicator

5. Voltage indicator

Figure 2 Product Display Description

1 2 3 4

Figure 3 Starting Current Output Interface and truck Battery Wiring

Note: Positive pole of outlet line is connected with the positive pole of

truck battery (Red). Negative pole of outlet line is connected with the

negative pole of truck battery (Black).

Note: The product can identify ignition start status automatically. Once

it is started successfully, if there is reverse current , the product will be

switched off automatically.

After the connection is connected properly, you can start the truck within

60s. If the truck is not started beyond 60s, the equipment is switched off

automatically. It requires you to disconnect the product with the connector of

auto battery and connect again. The system will re-start ignition function and

maintain for 60s. After the truck is started, please release the alligator clip

connected with the truck battery, and draw the start connection line from the

rear socket of the product.

Figure 4 LCD Display Status of Normal Starting Interface Connection

/DC SELECT: ON/OFF/DC Voltage Selection Key

/DC SELECT: Press to switch on the equipment and press the key to

select DC output voltage.

DC output voltage can be switched between DC 12 V and DC 19V. When

switching voltages, selected voltage is flashing. After pressing “DIM/ENTER”

key to confirm, the voltage character stops flashing, and DC outlet outputs

corresponding voltage.

To switch off the equipment, press“ /DC SELECT” key for at at least 3

seconds.

Note: There is no DC output under flashing status.

DIM /ENTER: LCD Backlight switch/DC voltage selection confirmation key In

ON mode, press “DIM/ENTER” key to switch on/off backlit. Under voltage

regulation status, press “DIM/ENTER” key to confirm currently selected

voltage.

Torch ON/ OFF

Press the Torch ON/ OFF button for about 3 seconds to turn on the torch.

After the torch is on, press the torch switch key to switch between “ON”,

“SOS” and “OFF” mode.

Under “ON” Status, press the torch switch key for about 3 seconds in

order to turn off the torch.

LED Warning Light Switch

The LED Warning Light is to warn the other vehicles not to collide with the

accident vehicle when the truck has failure. It can also be used as a lighting

device when repairing the truck.

Press the LED warning light switch for about 3 seconds to turn on the

LED warning light function.

The default setting is “traffic fault warning.

Press the key and choose the preferred model including traffic fault

warning”,“White lighting” and “OFF” mode.

Press the key for about 3 seconds in order to turn off the LED warning

light

To Jump Start a truck

Mode Definition:

Traffic Fault Warning: The red LED flashes twice followed by twice flashing

of white LED and then the same cycle repeats.

SOS: The light flashes in the cycle of triple short flashing---triple long

flashing—triple short flashing and then the same cycle repeats.

Note: Turn off the LED warning light by pressing the switch for at

least 3seconds when the it is not in use in order to extend the life of

battery.

Warning:

The product is for 24V vehicles. Do NOT connect it with 12V

vehicle to avoid any damage.

Jump-starting a truck can cause serious injury. If you are

unsure how to operate the equipment, please do not attempt

to jump-start your vehicle. Pls contact a qualified person for

assistance.

The product is for you to jump start the truck when the 24V battery is in

insufficient voltage, low temperature status or the truck cannot be started.

To jump start the truck, insert the starting output line into the EC5 interface

(positive pole is red and negative pole is black). Clamp the red alligator clip,

which is the positive pole of output line, on the positive pole of 24V battery,

and black alligator clip, which is the negative pole of output line, on the

negative pole of truck battery. If the connection is correct, LCD display of the

product will display a sign meaning the battery of the product is connected

with the battery of the truck and everything is ready. The built-in buzzer will

alarm twice with long buzzing. Then two continuous short "beep" sounds are

alarmed every two seconds to inform user the status is ready, please start

the truck right away. If the connection is reverse or the contact is unreliable,

it may result the product cannot be started automatically.

Inhaltsverzeichnis

Andere Jaycar Electronics Fernstartsystem Handbücher

Jaycar Electronics

Jaycar Electronics MB3730 Bedienungsanleitung

Beliebte Fernstartsystem Handbücher anderer Marken

AstroStart

AstroStart 803U Bedienungsanleitung

Durite

Durite 0-649-20 Handbuch

EINHELL

EINHELL BT-PS 1000 Handbuch

Linear

Linear ACCESS AK-21 Technische Daten

Soundstream

Soundstream TARANTULA RS.2 Bedienungsanleitung

Ultra Start

Ultra Start 72 Series Bedienungsanleitung

ADS

ADS FLASHLOGIC FLRSVW1 Bedienungsanleitung

Selecta

Selecta JS012 Bedienungsanleitung

Black Widow Security

Black Widow Security BW RAS 400 Bedienungsanleitung

Vector

Vector Power City DK080706 Beilage

Code Alarm

Code Alarm CA-535 Bedienungsanleitung

Ozito

Ozito OJS-800 Bedienungsanleitung

Profi-Partner

Profi-Partner 46387 Bedienungsanleitung

EZ STARTER

EZ STARTER EZ-45 Bedienungsanleitung

Viper

Viper 4204 Bedienungsanleitung

Essex Electronics

Essex Electronics KE-1701 Bedienungsanleitung

EINHELL

EINHELL EGS 3600 Handbuch

Rooboost

Rooboost RB-1750WP Bedienungsanleitung