JBL Control 24C/CT Micro Bedienungsanleitung

Control Contractor

Ceiling Loudspeakers

Control 24C/CT Micro and

Control 24CT MicroPlus

Owner's Manual

Product Description

Product Feature Identification

Installation Preparations

Step-By-Step Installation and Wiring

Painting the Speaker

Maintenance

Contacting JBL

Table of Contents

Thank you for purchasing JBL Control Contractor ceiling loudspeakers.

Read through this manual to familiarize yourself with the features,

applications and precautions before you use these products.

The JBL Control Contractor ceiling loudspeakers utilize innovative design and materials

to provide premium level performance from compact in-ceiling speakers.

CONTROL 24C MICRO - Most compact of the JBL ceiling speakers, the Control 24C

Micro contains a 4" woofer and a ¾" titanium-coated tweeter, providing high-fidelity

sound over an extremely wide coverage area. The Control 24C Micro also has a small

backcan and is ideal for smaller ceiling spaces.

CONTROL 24CT MICRO - The Control 24CT Micro includes a multitap transformer

for use on 70V or 100V line distribution systems. The transformer has a top tap rating of

9 Watts.

CONTROL 24CT MICROPLUS - The Control 24CT MicroPlus includes a multitap

transformer for use on 70V or 100V line distribution systems. The transformer has a top

tap rating of 25 Watts.

Product Description

Product Feature Identification

(Control 24CT Micro Shown)

Attachment Screw

Tweeter

Woofer

Steel Backcan

Connector

Block

Rotating

Mounting

Tab

Strain Relief

Tie

Seismic Tab

(Secondary

Support)

Attachment points

for included or

installer-provided

strain-relief fittings.

Tuning Port

Installation Preparations

OPTIONAL PRE-INSTALLATION BRACKETS

The entire installation can be accomplished, if necessary, without requiring access above

the ceiling. Bracketry for use with either suspended ceilings or sheetrock ceilings is

included. The speaker is held securely in place via mounting ears which lock into place.

IN MOST CASES,NO BRACKETS OTHER THAN THE ONES INCLUDED

WITH YOUR SPEAKER ARE REQUIRED. Everything needed for most installations

of these loudspeakers is provided with your Control Contractor ceiling speaker.

However, sometimes a pre-installation bracket is required to reserve the space within

the ceiling area, or to provide a place to which wiring can be tied behind the sheet rock.

A pre-installation bracket can also function as a cutout template when many cutouts are

to be made. Two types of pre-installation brackets are available from JBL Professional

as optional accessories:

1) The optional NEW-CONSTRUCTION BRACKET is made of flat sheet metal,

with wings to attach to the building structure. Holes are drilled for nails or screws at

16 inches (406 mm) and 24 inches (610 mm) on-center. Additional holes can be drilled

by the installer at other spacings up to a maximum of 24 ¾ inches (630 mm) apart.

Sheet rock installs over the bracket, and the bracket provides a template for blind

cutout of the hole in the sheet rock. The sheet rock can typically be cut with a router-

type cutting tool, using the bracket ring as a cutout guide.

Figure 1:

Optional New-Construction Bracket

2. The optional PLASTER-RING BRACKET (or "mud ring") is identical to the New

Construction Bracket, with the addition of a circular offset, forming an edge guide for

sheet rock plastering. The bracket has wings that attach to the building structure. Sheet

rock is typically either precut or cut with a rotary cutting tool. The sheet rock hole is

then plastered (or "mudded") up to the ring to create a seamless cutout.

NEW CONSTRUCTION BRACKETS

The model numbers for the New Construction Brackets for the Control 24C/CT Micro and

the Control 24CT MicroPlus are the same as the brackets for the Regular Control 24C & CT

ceiling speaker.

New Construction Bracket: MTC-24NC

Plaster Ring Bracket: MTC-24MR

USING INCLUDED C-BRACKET WITH SHEETROCK

For most installations, the INCLUDED C-shaped backing plate provides adequate reinforce-

ment to the ceiling material, spreading out the clamping force from the tab clamps.

CUTOUT SIZES

The speakers are packaged in cardboard cutout templates which can be used for scribing the

cutout hole onto your ceiling surface. The cutout size for the Control 24C/CT Micro and the

Control 24CT MicroPlus is the same as the Regular Control 24C & CT.

Cutout Size: 6.6 inches (168 mm)

Figure 2:

Optional Plaster Ring Bracket

ALL included support brackets, C-plate and tile rails

MUST be used when installing into suspended ceiling tiles.

FOR SAFETY: IMPORTANT TO USE BRACKETS

Suspended Ceilings - Insert the C-plate through the hole cut in the ceiling tile. Place

the C-plate around the hole with the tabs located as shown on Figure 4. Insert the tile

rails through the cut hole in the ceiling tile. Snap the two rails into the two tabs in the

C-plate and align the rails so that the ends extend OVER the T-channel grid on the

upper side of the tile. Secure the rails onto the C-bracket tabs by inserting a screw

though each tab into the rail. This can all be accomplished from below the ceiling tile,

if necessary.

The installation system has been designed so that the entire installation can be accom-

plished from beneath the ceiling, for instances when access above the tile is not possible

or practical. However, in some cases it may be easier with removable ceiling tiles to

access from both the top and bottom of the ceiling tile during various phases of the

installation.

Step 1 - Cut Ceiling Hole. Cut out the hole size either by tracing the cardboard cutout tem-

plate and cutting the hole or by using a circular cutter set to the cutout sizes listed above. Pull

the wiring through the cutout hole.

Guide to the Pins for Connection - The locking input connector contains 7 terminals,

as marked above the connector. The pin functions are listed on the label located on the

terminal cover plate.

Figure 3:

Hole Cutout

Step 2 - Insert Backing Hardware Through the Hole. Packaged with the speakers are two

types of backing hardware - a C-shaped backing-plate bracket and two tile rails.

Step-by-Step Installation and Wiring

Figure 4:

C-Bracket and Tile Rail

Positioning on Ceiling Tile

Tile Rails: The tile rails are designed to fit either standard 24-inch wide tiles or 600-mm

wide tiles. The tile rail pieces do NOT physically attach to the T-grid struts. Instead, the

inverted-V shape at the ends of the rails sit OVER the T-grid strut. During normal

operation, the rails are supported by the edge of the tile. In the unlikely even that the tile

comes out or falls apart, the ends of the support rails are designed to catch onto the T-

grid, providing secure support to hold the loudspeaker assembly in place.

Cutout Placement: The tile rails are pre-punched with attachment holes along their

length. Placement is not limited to the center of the tile, as is the case with many other

tile rail support systems.

Non-Suspended Ceiling Types: The C-bracket can be optionally used by itself to

shore up the ceiling material and to spread out the clamping force from the tab clamps.

Insert the C-plate through the cut hole in the ceiling and place it on the back side of the

hole before inserting the speaker.

Step 3 - Connect the Wiring to the Input Terminal Block. Connect the wiring to the UL &

CE-rated, touch-proof terminal block that is attached to the side of the speaker by stripping

the insulation back about about 3/16 inches (5 mm) [do not strip any longer than this], inserting

the bare end of wire into the connector and screwing the hold-down screw until tight using a

small flat blade screwdriver. Tighten any unused screws to avoid vibration.

Figure 5:

Connecting Wires to Connector

Control 24CT Micro:

9W4W2W1W0.5W Com 70V

N.C. 9W4W2W1WCom 100V

Control 24CT MicroPlus:

N.C. N.C. 6W 12W 25W Com 70V

N.C. N.C. 12W 25W N.C. Com 100V

Control 24C Micro: +-

Hookup Chart

For Control 24CT Micro and the Control 24CT MicroPlus, connect the negative input to

the "Common" terminal and connect the positive input to the appropriate tap. The input

pins correspond to the taps of the transformer indicated on the label above each connec-

tor. For example, if the system is being driven from a 70V Distributed Line, and the 2W

tap is the desired connection, the positive input would be made to the input marked "2W,

Violet." The negative connection would be made to the "Common" pin.

On the Control 24C Micro, low impedance version, connect the negative wire to the "-"

terminal and connect the positive wire to the "+" terminal.

All other pins are "No Connection."

Paralleling Input Terminals - It is common to run two sets of wires - one set is the

input to the speaker and the other is the feed to the next speaker. In this case, simply par-

allel the two sets of wires to the same terminals on the speaker's terminal block.

Guide to the Pins for Connection - The locking input connector contains 7 terminals,

as marked above the connector. The pin functions are listed on the label located on the

terminal cover plate.

Step 4 - Add included metal strain relief as necessary. The Control 24C/CT Micro and the

24CT MicroPlus are equipped with two locations where the installer can affix strain relief con-

nectors - one is on the back of backcan and one is on the side (for applications with shallow

access). The location of these two attachment points is shown on the Product Feature

Identification on Page 3. The installer can attach a wide variety of installer provided fittings to

these points if the included equipment is not adequate for the particular installation. Refer to

Figure 6 shows the strain relief INCLUDED with the Control 24C/CT Micro and Control 24CT

MicroPlus.

Figure 6:

Included Metal Strain Relief

1 - Cable Tie - If using loose wire, this cable tie can secure the loose ends of wire that

are connected to the terminal block. The strap can be tightened by pulling on the loose

end and then tightening the holding screw.

2 - Adjustable Metal Strap - This adjustable steel tie fitting is provided for those applica-

tions where it can be utilized to affix a set of wires. It can be useful for regions where

such a fitting is allowed for terminating a flexible conduit. It can also be used for tight-

ening down onto incoming wires to provide strain relief. It might be necessary to place

electrical tape or heat shrink over any wire bundle, underneath the metal strap, to physi-

cally protect the wire from the strap.

3 - PEM Screws - Two screws, which are threaded into PEM fittings in the backcan,

one on the back and one on the side, can be used to attach a wide variety of strain fit-

tings. Please remove the correct screws with the PEM fitting, as shown on the Product

Feature Identification Picture on Page 3, NOT the two screws that hold the backcan in

place. Check building codes in your area for what kind of physical strain relief fittings

are required in your region.

Always use the proper fitting in accordance with

your area's building codes and regulations.

CAUTION:

Figure 7:

Tightening the Cable Tie

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere JBL Sprecher Handbücher

Beliebte Sprecher Handbücher anderer Marken

argon audio

argon audio IE20 Bedienungsanleitung

Denon

Denon SC-N7 Bedienungsanleitung

Gemline

Gemline Ace 3952 Bedienungsanleitung

Focal

Focal ON WALL 300 Bedienungsanleitung

HEADRUSH

HEADRUSH Maximus HRSP 5024 Bedienungsanleitung

SoundLogic

SoundLogic BCCS-6/6395 Bedienungsanleitung

Peavey

Peavey DTH 218 Bedienungsanleitung

Avantree

Avantree Pluto Air Bedienungsanleitung

Morel

Morel Integra Series INTEGRA OVATION 4 Bedienungsanleitung

Oppo

Oppo SONICA Bedienungsanleitung

Bose

Bose SoundLink Wireless Music System Bedienungsanleitung

Rocksteady

Rocksteady Stadium Bedienungsanleitung

Bowers & Wilkins

Bowers & Wilkins 4 Bedienungsanleitung

Sonance

Sonance SONOS OUTDOOR Series Bedienungsanleitung

Electro-Voice

Electro-Voice EVID FM4.2 Bedienungsanleitung

Pioneer

Pioneer XW-HTD630 Bedienungsanleitung

Onn

Onn BWA16AA002 Bedienungsanleitung

HP GL313AA - USB Speakers PC Multimedia Bedienungsanleitung