JCM GLOBAL Taiko PUB-7 Bedienungsanleitung

Part No. 960-100919R_Rev. 1

March, 2017

JCM TRAINING

OVERVIEW

Taiko™Banknote Validator

(PUB-7/11)

Phone # (800) 683-7248

(702) 651-0000

Fax # (702) 651-0214

[email protected]

www.jcmglobal.com

Taiko™ Banknote Validator JCM Training Overview March, 2017

Page

Taiko™ Banknote Validator

Table of Contents

Overview.................................................................................. 3

Component Part Locations .......................................................................3

Taiko (PUB-7/11) DIP Switch Designations............................. 4

Enabling Taiko Features.......................................................... 5

Denomination Settings..............................................................................5

Accept Mode.......................................................................................................5

Inhibit Mode ........................................................................................................5

LED Pattern Selection Settings.................................................................6

Cleaning the Unit.......................................................................................7

Calibration ............................................................................... 8

Entering Test Mode.................................................................. 9

Functional Tests........................................................................................9

Aging Test Error Codes...........................................................................11

Error Codes - Bill Acceptance.................................................................13

Sensor Locations ....................................................................................15

Downloading Software........................................................... 16

PC Software Loading..............................................................................16

BlueWave 2.0™ Software Update...........................................................16

Cloning Software.....................................................................................17

Malfunction Errors ................................................................. 18

Red LED Error Code Definitions.............................................................18

Taiko Unit Parts List............................................................... 19

Personal Notes and Comments............................................. 20

Lecture Notes

Taiko™ Banknote Validator JCM Training Overview March, 2017

OVERVIEW

This training course addresses the following JCM Taiko™Series versions:

OMPONENT

ART

OCATIONS

Table 1 Various Taiko (PUB-7/11) Version Sensor Types

Unit Currency Sensors Available

PUB-7 Optical, Transparency and Reflective

PUB-11 Optical, Transparency, Reflective and Magnetic

Figure 1 Taiko (PUB-7/11) Primary Component Parts

A. Bezel

B. Bezel LED

C. Upper Guide Lid

D. Lower Guide Lid

E. Lower Lid Lock/Release Buttons

F. Banknote Insertion Slot

G. Banknote Exit Slot

H. Interface Connector

I. Maintenance Connector

J. Faceplate Installation Guide Pin

K. Upper Lid Open Close Button

L. Interface Connector

M. DIP Switch Block

March, 2017 JCM Training Overview Taiko™ Banknote Validator

TAIKO (PUB-7/11) DIP SWITCH DESIGNATIONS

The Taiko™Unit can be configured for various Communications Standards

and Protocols. Refer to the Taiko™Series (PUB-7/11) Operation and Mainte-

nance Manual (JAC Part No. 960-100175R), Tables 2-5, 2-6 and 2-7 for locat-

ing specific Connector Pin designations for either Serial/MDB, CC-Talk or

Pulse communication Protocols respectively.

Communications Protocols are selected via DIP Switch settings (Table 2).

Table 2 Typical Taiko DIP Switch Block Settings

SW No. DIP Switch Position Setting

1OFF Normal operation

ON Test Mode (Setting Mode)

2OFF 1-time scan (without validation retry)

ON 2-time scan mode (with validation retry)

3OFF When Pulse I/F Mode, depends on enable/disable signal.

ON When Pulse I/F Mode, always enabled.

4OFF 1 time Spin Mode (1 Drum Rotation Cycle)

ON 5 time Spin Mode (5 Drum Rotation Cycles - Anti-Fishing Prevention)

5Serial I/F Mode (DIP Switch 8 OFF) Pulse I/F Mode (DIP Switch 8 ON)

8OFF Serial I/F Mode (Selected by DIP Switches 6 and 7)

ON Pulse I/F Mode

NOTE: Always check the current Taiko™ Software Data Sheets to

verify the proper DIP Switch settings required for your particular Unit.

OFF

SW5 PULSE WIDTH

OFF 50ms/300ms

ON 50ms/50ms

SW6 SW7 I/F Setting

OFF OFF ID-003

ON OFF ID-0D3

OFF ON ID-0E3 (without

Encryption)

ON ON ID-0E3 (with

Encryption)

SW6 SW7 Number of PULSE

OFF OFF 1 Dollar = 1 Pulse

OFF ON 1 Dollar = 4 Pulses

ON OFF 1 Dollar = 10 Pulses

ON ON 1 Dollar = 20 Pulses

Taiko™ Banknote Validator JCM Training Overview March, 2017

ENABLING TAIKO FEATURES

The Taiko™setting for Banknote Acceptance and Front Panel LED Color

Pattern oscillations can be changed using DIP Switch enable routines.

ENOMINATION

ETTINGS

Specific Banknote denominations can either be accepted or rejected. To enable

the acceptance of particular Banknote denominations, use the following

“Accept Mode” Procedure.

Accept Mode

To enable Banknote acceptance, proceed as follows:

1. Remove power from the Taiko™Unit.

2. Set DIP Switches #1 and #6 to ON.

3. Reapply power to the Unit.

4. After the Front Panel LED flashes WHITE, turn DIP Switch #1 OFF.

The BLUE LED will begin to flash.

5. Insert the Banknote to be accepted.

The Banknote will be read and held in place, and the BLUE LED will be ON

(Steady). The Banknote will then be returned, and the BLUE LED will flash.

Acceptance of the selected Banknote denomination is now enabled.

6. Continue to insert each desired Banknote denomination that is to be accepted.

7. When done, remove power from the Taiko™Unit, reset the DIP Switches to

their normal operating positions, and reapply power to the Unit.

To disable the acceptance of particular Banknote denominations, use the

following “Inhibit Mode” Procedure. The default setting is to accept all

Banknotes programmed in the existing operating software.

Inhibit Mode

To allow the Taiko™Unit to reject or not accept a particular Banknote denom-

ination, proceed as follows:

1. Remove power from the Taiko™Unit.

2. Set DIP Switches #1, #6 and #7 to ON.

3. Reapply power to the Unit.

4. When the WHITE LED flashes, turn DIP Switch #1 OFF.

5. When the BLUE LED flashes, then flashes ORANGE, insert the Banknote that

is to be disabled or not to accepted.

The ORANGE LED will light steady while the Banknote is accepted and

returned. This denomination of Banknote is now inhibited from being accepted.

6. Continue inserting each specific denomination Banknote to be inhibited.

7. When done, remove power from the Taiko™Unit, reset the DIP Switches to

their normal operating positions, and reapply power to the Unit.

March, 2017 JCM Training Overview Taiko™ Banknote Validator

Lecture Notes

LED P

ATTERN

ELECTION

ETTINGS

The Bezel LED oscillating Pattern Color can be changed to oscillate between

two preset changing Color patterns.

To select and set Color Pattern #1, proceed as follows:

1. Remove power from the Taiko™Unit.

2. Set DIP Switches #1, #2 and #7 to ON.

3. Reapply power to the Taiko™Unit.

4. When the White LED begins to flash, turn DIP Switch #1 OFF.

The selected pattern is now set.

5. Remove power from the Taiko™Unit, reset the DIP Switches to their normal

operating positions, and reapply power to the Unit.

To select and set Color Pattern #2, proceed as follows:

1. Remove power from the Taiko™Unit.

2. Set DIP Switches #1, #3 and #7 to ON.

3. Reapply power to the Taiko™Unit.

4. When the White LED begins to flash, turn DIP Switch #1 OFF.

The selected pattern is now set.

Remove power from the Taiko™Unit, reset the DIP Switches to their normal operating

positions, and reapply power to the Unit.

Taiko™ Banknote Validator JCM Training Overview March, 2017

Lecture Notes

LEANING

THE

NIT

To clean a Taiko™Unit, follow these simple rules:

• Be careful not to scratch or damage any lenses while cleaning them.

• Use a mild soap and water solution ONLY with a lint free cloth.

• Wipe the lenses, drive rollers and Banknote transportation path clean.

• Remove the Lower Guide and clean any observable material build-up from the idler

rollers and the lower area of the Unit.

• Open the Upper Guide and clean any observable material build-up from the idler

rollers and the upper area of the Unit.

NOTE:Alcohol, Solvents or Citrus based cleaners should never

be used to clean a Taiko™ Unit!!!

March, 2017 JCM Training Overview Taiko™ Banknote Validator

Lecture Notes

CALIBRATION

Calibration of the Taiko™Unit should be done whenever Software is updated,

if the Taiko™Unit has been disassembled and/or if the CPU or Sensor Boards

have been replaced.

To calibrate a Taiko™Unit, follow these steps:

1. Remove the Taiko™Unit from its Faceplate mounting.

2. Set DIP Switches #1, #2 and #8 to ON.

3. Apply power to the Unit.

4. Confirm that the Front Panel LED is flashing WHITE.

5. Set DIP Switch #1 to OFF.

6. Confirm that the Front Panel LED is steady Lit GREEN.

7. Insert the KS-70 Reference Paper.

It will feed-in automatically and the GREEN LED will flash.

8. Set DIP Switch #8 to OFF.

The YELLOW LED will light and the Reference Paper will eject. the GREEN

LED will then flash.

9. Remove the Reference Paper from the Unit.

10.Set DIP Switch #8 to ON.

The YELLOW LED will light steady and then turn BLUE indicating calibration

is complete.

11.If the Front Panel LED turns RED, an error during calibration is indicated.

Isolate the problem by using the Error Code conditions listed in Table 7 on

page 18 of this Guide. Then re-calibrate the Taiko™Unit by following this

procedure from Step 1 again.

Taiko™ Banknote Validator JCM Training Overview March, 2017

Lecture Notes

ENTERING TEST MODE

Diagnostic Tests are initiated using DIP Switch #1.

To enter the Diagnostic Test Mode, proceed as follows:

1. Turn DIP Switch #1 ON

2. Apply power to the Taiko™Unit.

The Front Panel LED will flash White.

UNCTIONAL

ESTS

Table 3 lists the various Taiko™Unit Tests and their related DIP Switch

settings. Table 3 Taiko TEST DIP Switch Settings

Setting Function SW1 SW2 SW3 SW4 SW5 SW6 SW7 SW8

DIP Switch Test ON ON ON ON ON ON ON ON

Transport Motor Forward Rotation Test ON OFF OFF OFF OFF OFF OFF OFF

Transport Motor Reverse Rotation Test ON ON OFF OFF OFF OFF OFF OFF

Aging Test ON ON OFF ON OFF OFF OFF OFF

Solenoid Test ON ON ON ON OFF OFF OFF OFF

Acceptance Test ON OFF OFF OFF ON OFF OFF OFF

Entrance Flapper Test ON OFF OFF ON ON OFF OFF OFF

Exit Flapper Test ON ON OFF ON ON OFF OFF OFF

NOTE: DIP Switch #1 is used as the Enable/Disable Switch to

activate or deactivate each of the following Taiko™ Diagnostic Tests.

OFF

March, 2017 JCM Training Overview Taiko™ Banknote Validator

Lecture Notes

Test No. 1 - Transport Motor Forward Rotation Test

To perform Diagnostic Test #1, proceed as follows:

1. Set DIP Switch #1 ON, and apply power to the Taiko™Unit.

2. Set DIP Switch #1 OFF.

The following indications will occur:

•IftheBLUE LED begins Flashing, the Forward Motor rotational speed is cor-

rect.

•IftheRED LED is flashing, the Forward Motor speed is either too fast, or too

slow.

• Set DIP Switch #1 to ON to stop the Forward Motor Rotational Test.

Test No. 2 - Transport Motor Reverse Rotation Test

To perform Diagnostic Test #2, proceed as follows:

1. Set DIP Switch #1 and #2 ON, and apply power to the Taiko™Unit.

2. Set DIP Switch #1 OFF.

The following indications will occur:

•IftheBLUE LED begins Flashing, the Reverse Motor rotational speed is cor-

rect.

•IftheRED LED is flashing, the Reverse Motor speed is either too fast, or too

slow.

Set DIP Switch #1 to ON to stop the Reverse Motor Rotational Test.

Test No. 3 - Aging Test

To perform Diagnostic Test #3, proceed as follows:

1. Set DIP Switch #1, #2 and #4 to ON, and apply power to the Taiko™Unit.

2. Set DIP Switch #1 OFF.

The following indications will occur:

• The motor will cyclically rotate forward and reverse. The cycle will repeat until

the test is stopped or an error occurs.

• The BLUE LED will be lit steady. If an error occurs, the Bezel LED will flash

an error code. See Table 4 on page 11 for a list of Aging Test Error Conditions.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere JCM GLOBAL Banknotenprüfer Handbücher

JCM GLOBAL

JCM GLOBAL TBV Series Kurzanleitung zur Einrichtung

JCM GLOBAL

JCM GLOBAL VEGA Series Bedienungsanleitung

JCM GLOBAL

JCM GLOBAL DBV Series Kurzanleitung zur Einrichtung

JCM GLOBAL

JCM GLOBAL TBV-100 FSH Bedienungsanleitung

JCM GLOBAL

JCM GLOBAL RDM-100 Series Kurzanleitung zur Einrichtung

JCM GLOBAL

JCM GLOBAL iVIZION2 Series Kurzanleitung zur Einrichtung

JCM GLOBAL

JCM GLOBAL WBA Series Bedienungsanleitung

JCM GLOBAL

JCM GLOBAL UBA Pro Series Bedienungsanleitung

Beliebte Banknotenprüfer Handbücher anderer Marken

Alberici

Alberici BILLYONE UN1 Bedienungsanleitung

Kolibri

Kolibri Bishop Bedienungsanleitung

Royal Sovereign

Royal Sovereign RCD-2000 Bedienungsanleitung

Innovative Technology

Innovative Technology BV100 Bedienungsanleitung

Innovative Technology

Innovative Technology NV4 Bedienungsanleitung

Innovative

Innovative NV200 Bedienungsanleitung

Inves

Inves Secureuro Plus Bedienungsanleitung

ICT

ICT Bill Validator S7 Series Bedienungsanleitung

Kolibri

Kolibri Domino Bedienungsanleitung

CUMMINS ALLISON

CUMMINS ALLISON JetScan Bedienungsanleitung

Hamilton

Hamilton XE Kurzanleitung

CashCode

CashCode AMZ-154 Bedienungsanleitung

Innovate Technology

Innovate Technology NV10 Bedienungsanleitung

JCM

JCM iVIZION Handbuch

Innovative Technology

Innovative Technology NV10 Family Bedienungsanleitung

Amrotec

Amrotec MIB-11F Bedienungsanleitung

Crane

Crane NRI G-13.mft Standard Bedienungsanleitung

CASH TECHNOLOGY

CASH TECHNOLOGY CCE 20 Bedienungsanleitung