Jegs 95722 Bedienungsanleitung
User Guide for 95722
Portable Band Saw
5 in. x 5 in. Cutting Area
Tool Breakdown
1
Adjustable
Guide
5 in.
Brushes
Adjustable
Handle
LED Light
Light
Switch
Speed
Control Trigger
Guide
Rollers
Blade
Tension
Handle
Plastic
Bumpers
5 in.
General Safety Information Usage
Please read the following safety information.
•
When operating outdoors, use an extension cord
intended for outdoor use.
• Check electrical cord for damage prior to every
use to reduce risk of electrocution.
• Ensure safety with proper PPE. Wear goggles/
face shield, ear protection and a respirator.
•
Dress properly. Do not wear open toe shoes,
loose clothing or jewelry. Keep hair, clothing, and
gloves away from moving parts.
• Do not force the saw.
•
Disconnect from power source when not in use.
• Store out of reach of children.
•
Always check blade alignment prior to use. Adjust
as necessary.
•
Monitor blade sharpness. Dull blades will lengthen
cutting times and increase the risk of injury.
1. Installing the Blade
•
Place the band saw on a table or bench with
the drums facing you.
•
Turn the tension handle clockwise to the
“Loose” setting.
•
Fit the blade, with the teeth facing toward you,
around the drums and between the guide
rollers. You hill have to adjust the blade angle
to fit between the rollers.
•
Make sure the blade is centered on the rollers
and evenly located around the drums.
•
Turn the tension handle counter-clockwise
to the “Tight” setting
2
Band Saw Safety
• Hold the saw by the insulated handles.
• Never leave the saw unattended when running.
•
Before each use put the tension handle in the
tightened position.
•
Make sure that the material being cut is securely
fastened to a work surface. Work slowly and
carefully when cutting corner, sharp edges, and
ragged welds to avoid the blade snagging.
•
Both the material being cut and band saw motor
housing can get very hot during operation. If this
happens, stop and allow the motor to cool before
restarting. Water or coolant can be sprayed onto
the blade to reduce heat.
•
This tool vibrates during use. Stop use if you
experience tingling, numbness, white or blue
fingers. Gloves may help reduce vibration effects.
Turn lever counter-clockwise
to tighten blade
Blade fits
around drums
and is aligned
by roller guides
Usage Contd.
3
Loosen to
adjust
2. Guide Bar Adjustment
• To adjust the height of the guide loosen the
two allen head screws. There is 1
5
/
8
in. of
movement up and down. Once set to the
desired height, tighten the allen screws.
Speed Adjustment
Trigger
3. Cutting
•
Make sure the trigger is released before
plugging the tool into power source.
• Secure item to be cut to workbench or solid
surface.
• Ensure cord is out of the cutting path.
•
Set guide bar against workpiece. Keep blade
at a 90º angle to the workpiece.
• Select blade speed, between 1-6, on radial
dial located next to trigger.
•
Squeeze trigger and allow band saw to reach
full speed before starting the cut.
•
To start the cut, use minimal force to create a
groove. Once a groove has been made allow
gravity to bing the rest of the blade into use.
(Note: Do not apply force by pressing down
on the tool. The band saw’s weight is enough
to make a clean cut.)
• As you reach the end of the cut, slowly raise
the band saw and remove from work space.
•
To prevent the risk of injury, turn off and
unplug tool.
Maintenance
• Prior to Use Checklist:
• Hardware (does it need tightened)
• Binding or misalignment of moving parts
• Damage to cord insulation, exposed wiring
• Cracked or broken parts
• Post-Project Checklist:
•
Wipe saw free of dust and debris with a clean
cloth, or rag.
• Check condition of blade teeth. Replace the
blade is excessive wear it noted.
• Remove blade if saw is not going to be used
in the near future.
Andere Jegs Gesehen Handbücher
