JEM TECHNO-HAZE Bedienungsanleitung
MANUFACTURED BY
MARTIN MANUFACTURING (UK) PLC
BELVOIR WAY,
FAIRFIELD INDUSTRIAL ESTATE,
LOUTH, LINCOLNSHIRE. LN11 0LQ.
TEL:(01507) 604399 FAX:(01507) 601956
MARTIN MANUFACTURING (UK) PLC
USER GUIDE
VERSION 1.4
Techno-Haze
TechnoHaze performance
‘Performance’
www.audiovias.com
MARTIN MANUFACTURING (UK) PLC
TECHNO-HAZE USER GUIDE
Pro-Haze
Fluids suitable for this machine:
Note:
The JEM warranty will be void if any fluid other then JEM approved fluid is used. If
other fluids are used there could be serious damage to the machine and the fluid
may not of been tested for use in public areas.
TECHNO-HAZE USER GUIDE
How To Contact Us
Address:
Telephone:
Fax:
Email: [email protected]
Website: Http://www.jemsmoke.com/
PAGE 9
MARTIN MANUFACTURING (UK) PLC
Martin Manufacturing (uk) Plc
Belvoir Way,
Fairfield Industrial Estate,
Louth, Lincolnshire. LN11 0LQ.
+44 (0) 1507 604399
+44 (0) 1507 601956
www.audiovias.com
PAGE 8
TECHNO-HAZE USER GUIDE
Trouble Shooting
CAUSE CURE
SYMPTOM
The mains switch does not light
when I switch on.
Main fuse blown..
No power connected.
Check main fuse.
Check power is connected.
The power LED does not light on
the remote control.
Fuse on main PCB blown.
Remote control not connected.
Check fuse on Main PCB.
Check connection of remote control.
The ready LED does not light.
even after 15 minutes.
Thermocouple fault
Thermal trip fault
Contact your Distributor.
No haze output. Low fluid level.
No fluid in container.
Check fluid level LED.
Replenish fluid container.
MARTIN MANUFACTURING (UK) PLC
•
•
•
•
•
•
•
•
User Guide Index
Introduction
Safety
Machine Layout
Getting Started
Using The Remote Control
Trouble Shooting
How To Contact Us
PAGE 1
TECHNO-HAZE USER GUIDE
MARTIN MANUFACTURING (UK) PLC
Note:
Martin Manufacturing (UK) reserves the right to modify or change the
specification of this product without prior notice.
No part of this publication shall be copied without permission
© Martin Manufacturing (UK). 1999
www.audiovias.com
TECHNO HAZE USER GUIDE
Introduction
The TECHNO-HAZE has been designed to produce a perfect translucent
environment for today’s intelligent lighting effects.
Furthermore, this unique design is guaranteed to give the user maximum
reliability thanks to features such as the “Low fluid cut off system”,which
protects the pump in the event of machine running out of fluid.
Creating the perfect ambient haze relies heavily on the correct particle size
and dispersion. The TECHNO-HAZE produces this by vapourising the special
working fluid at very precise temperature in a high mass heater block which
contains a cuperous helicoil of 3 metres length.
The product of this process is injected into the uniquely designed JEM
‘Expansion Chamber’ where it is mixed with a turbulent airflow and projected
from the machine as an optically translucent haze at 1200 ft / minute (exit
velocity).
The Techno-Haze uses a ‘Direct Thermal Protection Device’ to ensure maximum
overheat protection and therefore greater reliability.
“DTP” Safety system
SMD electronics
Low fluid cut off system
Variable output remote
2.5 Litre fluid capacity
Expansion chamber
High power fan
Features
•
•
•
•
•
•
•
the
PAGE 2 MARTIN MANUFACTURING (UK) PLC PAGE 7
MARTIN MANUFACTURING (UK) PLC
Remote Control Functions
•
•
OUTPUT LEVEL CONTROL:
Use the control to
give the output density you require.
Setting the level control to minimum will switch off the output
POWER LED: This indicates that the machine is powered and that the
remote is connected.
When starting the machine for the first time,
use the prime button as described on page 5 para 2. During normal opera-
tion, the output control should be set between 4 and 10.
TECHNO HAZE USER GUIDE
www.audiovias.com
TECHNO HAZE USER GUIDE
PAGE 6
Using The Remote Control
The Technohaze comes with a compact remote allowing the user to prime the pump
and control the output level.
MARTIN MANUFACTURING (UK) PLC
1
2
3
456
7
8
9
OUTPUT
PRIME
ON
OUTPUT CONTROL
POWER
LED
PRIME
BUTTON
TECHNO HAZE USER GUIDE
Safety
•
•
•
•
•
•
•
Always use a JEM approved fluid, other fluids could be dangerous and could
cause damage to the machine.
Always check the voltage is correct for use with the machine, the voltage
setting is printed on the serial label.
Always read the user guide before operating the machine, smoke machines
need to be operated carefully to avoid risk.
Do not remove the cover or attempt to repair a faulty machine, an authorized
JEM dealer should be contacted in the event of a faulty machine.
Always use smoke machines in well ventilated areas, over use could affect
sufferers of asthma or other chest conditions.
Do not use the machine if there is a faulty mains lead or plug this could be
dangerous.
Do not spill fluid over the machine, if fluid is spilt clean with clean water and
contact an approved JEM dealer for advice.
Mains Lead Wiring Instructions
Brown = Live
Blue = Neutral
Green/Yelllow = Earth
Note! This Appliance must be earthed
PAGE 3
MARTIN MANUFACTURING (UK) PLC
www.audiovias.com
TECHNO HAZE USER GUIDE
Machine Layout
PAGE 4 MARTIN MANUFACTURING (UK) PLC
FLUID OUT
LED
READY LED HEAT LED
FLUID
COMPARTMENT
FA N
REMOTE CONNECTION
MAINS SWITCH
POWER LEAD
TOP VIEW
REAR VIEW
PAGE 5
TECHNO HAZE USER GUIDE
Getting Started
•
•
•
Once you have selected the best position for the TECHNO- HAZE you can
begin to use the machine. First check the power supply you have is correct
for the machine .If it is, you can connect to the power supply and switch the
mains switch on at the rear of the machine; the machine will start to heat up
and the fan will run. It will take approximately 10 minutes for the machine to
reach working temperature. While it heats up you should check the level in
the fluid container; the container can hold up to 2.5 litres of fluid. The
machine may not heat if there is inadequate fluid in the container (the red
‘fluid out’ LED must not be on).
When you have finished using the machine you should turn the mains switch
off. If any problems occur when operating the TECHNO-HAZE please refer
to the trouble shooting guide.
When the machine has reached working temperature the green “ready” LED
will light on the top of the machine and the machine can now be operated.
Press the prime button until haze appears from the output; the pump is now
primed. This will only have to be done if the fluid lines have become empty.
The output can now be set to the desired level by turning the “output” knob.
MARTIN MANUFACTURING (UK) PLC
www.audiovias.com
Inhaltsverzeichnis
Andere JEM Nebelmaschine Handbücher
JEM
JEM HEAVY FOG GLACIATOR Bedienungsanleitung
JEM
JEM AF-2 Bedienungsanleitung
JEM
JEM Glaciator X-Stream Bedienungsanleitung
JEM
JEM Glaciator Dynamic Bedienungsanleitung
JEM
JEM ZR12-DMX Bedienungsanleitung
JEM
JEM ZR33 HI-MASS Bedienungsanleitung
JEM
JEM ZR12-AL Bedienungsanleitung
JEM
JEM MARTIN Hydra Bedienungsanleitung
JEM
JEM Glaciator X-Stream Bedienungsanleitung
JEM
JEM Roadie Compact Bedienungsanleitung
Beliebte Nebelmaschine Handbücher anderer Marken
Antari
Antari ICE Bedienungsanleitung
Boost
Boost BOOST-FOG400LED-BK Bedienungsanleitung
Home Accents Holiday
Home Accents Holiday FM1000-ASH Bedienungsanleitung
EuroLite
EuroLite ZEITGEIST FOG-1200 Bedienungsanleitung
Dyna-Fog
Dyna-Fog CYCLONE ULTRA 2734 Bedienungsanleitung
PROEL
PROEL DRAGO HEAVY PLFD150HY Bedienungsanleitung
