Jenn-Air XT7036ADS Bedienungsanleitung

RANGE HOOD

Model Number:

Manufacturer Number:

Size:

JXT7036ADS JXT7142ADS

MK8200 MK0842

34" 39" Liner

JXT7148ADS

MK0848

45" Liner

INSTALLATION

GUIDE

TABLE OF CONTENTS

Safety Instructions ................................................... 1

Mounting Heights ..................................... 2

Ducting .................................................................... 3

Specifications ........................................................... 4

Installation ............................................................... 5

Electrical ................................................................. 5

Liners ...................................................................... 6

Form No. A/04/03 Part No. IMK8200-0303A ({)2003 Maytag Appliances Sales Co. Litho U.S.A.

MODELS:JXT7036ADS JXT7142ADS JXT7148ADS

Installation

Theinstallationin thismanualisintendedforqualifiedinstallers,servicetechniciansor persons

withsimilarqualifiedbackground.DONOTattempttoinstallthisapplianceyourself.Injurycould

resultfrominstallingtheunitdueto lackofappropriateelectricalandtechnicalbackground.

All electricalwiring mustbe properlyinstalled,insulatedand grounded.Overlyaccumulated

greasein oldductworkshouldbecleanedoutorductworkshouldbereplacedif necessaryto

avoidthepossibilityof agreasefire.Checkalljointson ductwork toinsureproperconnection

andalljoints shouldbeproperlytaped.

* Pleasecheck for latest specification revisions before any custom work or cutouts.

INSTALLATION

MOUNTINGHEIGHTS

Min 24"-M_}x 32"

Minimummountingheightbetweenrangetop

tohoodbottomshouldbenolessthan24".

Maximum mounting height should be no

higher than 32".

It is important to install the hoodat the

proper mounting height. Hoods mounted too

low could result in heatdamage and fire

hazard;while hoodsmounted too high will be

hard to reach and will lose performance and

efficiency.

If available,also refer to range manufacturer's

height clearance requirements andrecom-

mended hood mounting heightabove range.

DUCTING

A minimum of 8" round or 3-1/4" x lO"rectangular

duct must be used to maintain maximum air flow

efficiency.

Always use rigid-type metal ducts only.

Flexibleducts could restrict air flow byup to 50%.

Also use calculation (onright) to compute total

available duct run when using elbows, transitions

and caps.

ALWAYS,when possible,reduce the number of

transitions and turns. Iflong duct run is required,

increase duct size. If a reducer is used,install a

long reducer insteadof a pancake reducer. Reduce

duct size as far away from openingas possible.

Ifturns or transitions are required:

Install asfar away from openingand as far

apart, between 2, as possible.

DuctRunCalculation:

Maximumrun

100 FT

Deduct:

each90 Elbowused 15 FT

each45 elbow used 9 FT

SideWallCapw/damper 30 FT

RoofCap 30 FT

e,g.- I roof cap,2x90 elbows, 145 elbow used;

=30' + 30' + 9' =69' used, 31' availablefor straight duct runs,

INSTALLATION O

DUCTING

NEVERexhaustair or terminate duct work into spacesbetween walls, crawl spaces,ceiling, attics or

garages.All exhaust must be ducted to the outside.

UseMetal ductwork only.

Fastenall connectionswith sheet metal screws and tape alljoints w/certified Silver Tapeor DuctTape.

SomeDuctingOptions:

sidewall cap

w/gravity damper

........... !\

RoofPitchw/

Flashing&Cap

\u\

INSTALLATION

SPECIFICATIONS

Model:

JXT7036ADS

15-1/4"

33-3/8"

¢/L

cut out dimension

115-3/8"

(cutout)

f 33-1/2", 38-I/2", 44-1/2" (cutout) = cutout dimension

INSTALLATION

Mountingthe RangeHood

I. Determineandmarkthemounting

positionof therangehoodwith a

pencil.

2.Cutouttheopeningwherethe

rangehoodwill beinstalled.

3.Installductworkandelectrical.

Ducttapeall ductconnections

with certifiedductorsilvertape.

4.Positionrangehoodintolocation.

Apringloadedlatchon oneside,

will lockintopositionto help

supportthehood.

5. Supportingtheotherendofthe

hood,fastenwoodscrewsthrough

pre-drilledholesintowoodframe

opening.

ELECTRICAL

Iductlsilver

tape

Duc[work CORRec[io#

Locking_ch Powersupplycane Screw inplace

Eetryinto rangehoed

All Electricalwork mustbyperformedbyqualifiedelectricianor personwith similartechnicalknowhewand

background.

Forpersonalsafety,removehousefuseoropencircuitbreakerbeforebeginninginstallation.

Donotuseextensioncordor adapterplugwith thisappliance.

FollowNationalelectricalcodesor prevailinglocalcodesandordinances.

ElectricalSupply:

Thisappliancerequiresa 120V60Hzelectricalsupplyandconnectedto anindividual,properlygroundedbranch

circuit,protectedbya 15or 20amperecircuitbreakeror timedelayfuse.Wiringmustbe2 wirew/ground.

Pleasealsoreferto ElectricalDiagramlabeledonproduct.

Cable Lock:

Acable locking connector (not

supplied) might also be required by

local codes.Checklocal

requirements andcodes, purchase

and install appropriateconnector

if necessary. CableLock

INSTALLATION

LINERS

JXT7142ADS

JXT7148ADS

Optionalstainless liners JXT7142ADS,JXT7148ADS,are availablefor lining custom canopies

before installing the JXT7036ADSpower blower pack system.

customcanopy

I 3£" or 45

42" or 48"

OptionaIStainless Liner:

JXT7142ADS

JXT7148ADS

HOTTE DE CUISINIERE

Numero de modele:

Numero du fabricant:

Dimensions:

JXT7036ADS JXT7142ADS JXT7148ADS

MK8200 MK0842 MK0848

34" 39" Revetements 45" Revetements

protecteurs interieurs protecteurs interieurs

INSTALLATION

GUIDE

TABLE DES MATIERES

Consignes de securite .............................................. 1

Hauteurs de montage 2

Canalisation ............................................................. 3

Caracteristiques techniques ...................................... 4

Installation .............................................................. 5

Electrique ................................................................ 5

Rev#tements protecteurs interieurs .......................... 6

Form No. A/04/03 Piece No. IMK8200-0303A _2003 Maytag Appliances Sales Co. Litho Dats-Unis

MODELES:JXT7036ADS JXT7142ADS JXT7148ADS

Installation

Lesproceduresd'installationdecritesdansceguides'adressentadesinstallateursqualifies,

destechniciensdeserviceoua despersonnespossedantdescompetencessimilaires.NEten-

tez PASd'installercet appareilvous-meme.L'installationde I'unitepeutcauserdesblessures

enraisond'unmanquedeconnaissancestechniquesetelectriques.

Toutle c_blage electrique doit etre correctement installe, isoleet mis a la masse.Lesvieuxsys-

temes de conduitsdoivent etre debarrassesde toute accumulation excessivede graisse. Sicela

est impossible, les conduits doivent etre remplaces afin d'eviter les incendies de graisse.

Assurez-vous que les raccords des systemes de conduits sont solidaires et adequatement

rubanes.

* Veuillez vousprocurer les revisions les plus recentes des caracteristiques techniques

avant deproceder a des travaux sur mesure ou de decoupe.

INSTALLATION

HAUTEURSDE MONTAGEET DEGAGEMENT

r I

I I

Min 24"-M_}x 32"

La hauteur de montage minimale entre le

dessus de la cuisiniere et le dessous de hotte

doit etre d'au moins 61 cm (24 po).

La hauteur de montage maximale ne doit pas

exceder 81,3 cm (32 po).

IIest important d'installer la hotte a la hauteur

appropriee. Une hotte trop basse peut causer

des dommages par la chaleur ou des risques

d'incendie tandis qu'une hotte trop haute sera

difficile a atteindre et perdra de son efficacite.

Reportez-vousauxexigencesrelatives a la hau-

teur de degagement du fabricant de la

cuisiniere et a la hauteur de montage au-

dessus de la cuisiniere recommandee pour la

hotte.

CANALISATION

Unconduit rond dun diametre minimumde 15,2cm

(6po)ouun conduitrectangulairede8,3cm x25,4cm

(3 1/4pox 10 po)doitetre utilisepourassurerunecir-

culationd'air optimale.

Utiliseztoujoursdesconduitsmetalliquesrigides.

Les conduits flexibles reduisent la circulation daft

dansune proportionqui peutatteindre50 %.

Utiliseztoujours lesvaleursde droite pour calculerle

trace de conduits possibles Iors de I'utilisation de

coudes,detransitionset de capuchons.

UtilisezTOUJOURSun nombreminimal de transitions

et de courbes. Pourun long trace de conduits,aug-

mentezles dimensionsdesconduitsde15,2cm (6po)

17,8 cm a 20,3 cm (7 ou 8 po). Lecas echeant,

privilegiezleslongsreducteursaux reducteursdetype

plat. Reduisezlesdimensionsdu conduitaussiloinde

I'ouverturequepossible.

Sides courbesoudestransitionssont utilisees:

Eloignez-lesautantque possiblede I'ouvertureet

desautrescourbesou transitionsau momentde

I'installation.

Calculdu trace deconduits:

Tracemaximum

20.32 cm (8 po) 30,5 M ( 100 PI)

Deduisez:

chaquecoudede90 o utilise 4,6 M (15PI)

chaquecoudede45 o utilise 2,7 M(9 PI)

Capuchonmural lateralavec registre 9,1 M (30PI)

Capuchondetoit 9,1 M (30PI)

p. ex. -1capuchon de toit, 2 coudesde 90o, 1 coudede

450utilise :

= 9,1 m + 9,1 m + Z7m = 20,9 m (30pi +30pi +9pi =69pi)

utilises, 9,4 m (31 pi) disponiblepour los trac#s en ligne droite,

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Sprachen:

Andere Jenn-Air Dunstabzugshaube Handbücher

Jenn-Air

Jenn-Air JXT6030ADR Gebrauchsanweisung

Jenn-Air

Jenn-Air JXT8030ADS Bedienungsanleitung

Jenn-Air

Jenn-Air JXT9030BDP Installationsanleitung

Jenn-Air

Jenn-Air JXU9130HP Produktinformationsblatt

Jenn-Air

Jenn-Air JXI8936DS Produktinformationsblatt

Jenn-Air

Jenn-Air JXA9030CDP Bedienungsanleitung

Jenn-Air

Jenn-Air JXU9136WP0 Bedienungsanleitung

Jenn-Air

Jenn-Air JVR0430HS Produktinformationsblatt

Jenn-Air

Jenn-Air JXT7036ADS Bedienungsanleitung

Jenn-Air

Jenn-Air JXU9136WP Produktinformationsblatt

Jenn-Air

Jenn-Air JXT8142ADS Bedienungsanleitung

Jenn-Air

Jenn-Air JXT8136ADS Bedienungsanleitung

Jenn-Air

Jenn-Air JXW5036WS Produktinformationsblatt

Jenn-Air

Jenn-Air JXT8836ADS Bedienungsanleitung

Jenn-Air

Jenn-Air JXT8030ADS Bedienungsanleitung

Jenn-Air

Jenn-Air JXT9130CDP Bedienungsanleitung

Jenn-Air

Jenn-Air JXT8136ADS Bedienungsanleitung

Jenn-Air

Jenn-Air JXT19130CDP Bedienungsanleitung

Jenn-Air

Jenn-Air S99E30S Bedienungsanleitung

Jenn-Air

Jenn-Air JXT7036ADS Bedienungsanleitung

Jenn-Air

Jenn-Air JXI5036WS Produktinformationsblatt

Jenn-Air

Jenn-Air UXT2030AYB Gebrauchs- und Wartungshandbuch

Jenn-Air

Jenn-Air JXD7836BS0 Bedienungsanleitung

Jenn-Air

Jenn-Air 36" ISLAND CANOPY RANGE HOOD Produktinformationsblatt

Beliebte Dunstabzugshaube Handbücher anderer Marken

emmeti

emmeti RECUPA MED A-140 Leitfaden

Nibe

Nibe F135 Bedienungsanleitung

Kuppersberg

Kuppersberg INTRO 60 Montage- und Wartungsanleitung

Zephyr

Zephyr Spruce AK9834BS Installationsanleitung

Hisense

Hisense MH6INBG Bedienungsanleitung

Miele

Miele DA 1255 Bedienungsanleitung

Broan

Broan 46000 Bedienungsanleitung

GE Profile PV977 Originalbetriebsanleitung

FALMEC

FALMEC FFRIA24W5FS Bedienungsanleitung

Whirlpool

Whirlpool RH2600XL-1 SERIES Bedienungsanleitung

Küppersbusch

Küppersbusch DX ISLA Bedienungsanleitung

ETNA

ETNA AV360RVS Bedienungsanleitung

JUNO

JUNO JDF603E6 Bedienungsanleitung

Miele

Miele DA 6708 D Bedienungsanleitung

Tricity Bendix

Tricity Bendix LE 150 Handbuch

AEG

AEG X68163BV1 Bedienungsanleitung

AEG

AEG 125 D Bedienungsanleitung

Smeg

Smeg KSEV97X Bedienungsanleitung