Jensen VM9114 Bedienungsanleitung
1
VM9114
VM9114 Head Unit
Single DIN Sleeve
Wiring Harness
Parking Brake Sensor Extension Wire
Mounting Hardware
Cosmetic Trim Ring
3.5mm to 3.5mm Media Adaptor Cable
Owners Manual
Installation Guide
What’s in the Box
You will need these tools and supplies to install your VM9114:
• Torx type, flat-head and Philips screwdrivers
• Wire cutters and strippers
• Tools to remove existing radio (screwdriver, socket wrench set or other tools)
• Electrical tape
• Crimping tool
• Volt meter/test light
• Crimp connections
• 18 gauge wire for power connections
• 16 – 18 gauge speaker wire
Tools and Supplies
Installation Guide
Instruccionnes de Instalación
Instructions d’installation
WARNING! Never install this unit where operation and viewing could interfere with safe driving
conditions.
Para obtener instrucciones en Español, diríjase a la página 5. Pour des instructions en Francais, référez-vous à la page 9.
EJECT
A/V
INPUT
VM9114
160 Watts
Multimedia Receiver
2
TAB
DASHBOARD
DASHBOARD
TAB
Disconnecting the Battery
To prevent a short circuit, be sure to turn off the ignition and remove the negative (-) battery cable prior to in-
stallation.
NOTE: If the VM9114 is to be installed in a car equipped with an on-board drive or navigation computer, do
not disconnect the battery cable. If the cable is disconnected, the computer memory may be lost. Under these
conditions, use extra caution during installation to avoid causing a short circuit.
Pre-installation
Remove the four screws that attach the mounting sleeve to the
radio and remove the sleeve.
Install the mounting sleeve.
a. Install mounting sleeve into the dashboard or optional
adapter. Do not force the sleeve into the opening or cause
it to bend or bow.
b. Locate the series of bend-tabs along the top, bottom and
sides of the mounting sleeve. With the sleeve fully insert-
ed into the dashboard opening, bend as many of the tabs
outward as necessary so that the sleeve is firmly secured
to the dashboard.
c. Install support strap to make the unit more stable.
Place the radio in front of the dashboard opening so the wiring
can be brought through the mounting sleeve.
CAUTION! Be careful not to damage the car wiring.
1
2
3
EJECT
A/V
INPUT
3
Wiring
WARNING! Only connect the unit to a 12-volt power supply with proper grounding.
Complete wiring as illustrated in the wiring diagram on page 4. Once the wiring is complete, reconnect the bat-
tery negative terminal. If there is no ACC available, connect the ACC lead to the power supply with a switch.
NOTE: When replacing a fuse, be sure to use correct type and amperage to avoid damaging the radio. The
VM9114 uses one 15 amp fuse, located in the black filter box in-line with the main wire harness.
Final Installation
After completing the wiring connections, turn the unit on to confirm operation (ignition switch must be on). If
unit does not operate, recheck all wiring until problem is corrected. Once proper operation is achieved, turn off
the ignition switch and proceed with final mounting of the chassis.
Connect wiring adapter to existing wiring harness.
Connect antenna lead.
Carefully slide the radio into the mounting sleeve, making
sure it is right-side-up, and secure with the original 4 screws.
Attach one end of the perforated support strap (supplied) to
the screw stud, which is screwed into the threaded insert on
the back of the unit, using the hex nut provided. Fasten the
other end of the perforated strap to a secure part of the
dashboard either above or below the radio using the screw
and hex nut provided. Bend the strap to position it as
necessary.
Replace any items you removed from the dashboard.
ISO-DIN Installation
Remove mounting sleeve brackets.
Remove trim ring.
Mount factory brackets on new radio using existing screws
from old radio.
Slide radio chassis into dash opening and secure.
Re-install dash panel.
EJECT
A/V
INPUT
EJECT
A/V
INPUT
1
2
3
4
5
1
2
3
4
5
CAUTION! The rear of the radio must be
supported with the strap to prevent dam-
age to the dashboard from the weight of
the radio or improper operation due to
vibration.
NOTE: For proper operation of the CD/
DVD player, the chassis must be mounted
within 20° of horizontal. Make sure the unit
is mounted within this limitation.
Remove Mounting
Sleeve Brackets
EJECT
A/V
INPUT
4
Harness Cord
Auto antenna control (connect to antenna
control lead & power supply of antenna
amplifier)
External power amplifier control
Antenna Jack
REAR R
REAR L
BLUE
BLUE/WHITE
WHITE/BLACK -
GREEN/BLACK -
WHITE +
GREEN +
PURPLE +
PURPLE/BLACK -
GREY/BLACK -
GREY +
Car
Mute (leave open if not connected)
BROWN
Car Phone
FRONT L
FRONT R
REAR R
REAR L
MUTE
P.CONT
ANT.CONT
ACC
BLACK
YELLOW
RED
FUSE (15A)
Battery
Ignition Switch
BATTERY
BATTERY +
Ground
BATT
ACC
GND
PINK
External Power Amplifier
Antenna
PRK SW
PARKING BRAKE
Wiring Diagram
IMPORTANT: Incorrect wiring connections can damage the unit. Follow the wiring instructions carefully, or
have the installation handled by an experienced technician.
Need Help?
For technical assistance, call the Jensen
customer support line at 1-800-323-4815.
Andere Handbücher für VM9114
1
Inhaltsverzeichnis
Andere Jensen Autoempfänger Handbücher
Jensen
Jensen VX7020 Bedienungsanleitung
Jensen
Jensen MP3510 Bedienungsanleitung
Jensen
Jensen MPX6411 - Radio / CD Bedienungsanleitung
Jensen
Jensen MS2A Bedienungsanleitung
Jensen
Jensen CD510K Bedienungsanleitung
Jensen
Jensen JBR550 Bedienungsanleitung
Jensen
Jensen VM8013HD - Screen MultiMedia Receiver Bedienungsanleitung
Jensen
Jensen VX7024 Datenblatt
Jensen
Jensen CD315X Bedienungsanleitung
Jensen
Jensen CD511K Merkblatt
Jensen
Jensen AM/FM RADIO WITH AUDIO CASSETTE PLAYER Bedienungsanleitung
Jensen
Jensen MP5010K - 240 Watt AM/FM Bedienungsanleitung
Jensen
Jensen CD6112 - CD Receiver Bedienungsanleitung
Jensen
Jensen cd3010x Bedienungsanleitung
Jensen
Jensen VM9512 - Motorized Touch-Screen Multimedia... Bedienungsanleitung
Jensen
Jensen VX4010 Bedienungsanleitung
Jensen
Jensen VM9216BT Bedienungsanleitung
Jensen
Jensen JCD2006 Bedienungsanleitung
Jensen
Jensen MSR4050G - Radio / CD Player Bedienungsanleitung
Jensen
Jensen HR9000PKG Bedienungsanleitung
