Jet-tech 737E Bedienungsanleitung
1
JET TECH TECHNICAL MANUAL
737E VER1.02 2015/12
2
Contacts
Tools
Some of the tools you will need
to repair and service the 737e.
Volt Meter
Temperature meter
Allen Keys (Metric)
Phillips screw driver
Nut drivers (Metric)
Wrenchs (Metric)
US Metric
(inches) (mm)
1/8 3.18
5/32 3.97
4
3/16 4.76
5
13/64 5.16
7/32 5.56
15/64 6.05
6
1/4 6.35
17/64 6.75
7
9/32 7.14
5/16 7.94
8
11/32 8.73
9
3/8 9.53
10
11
7/16 11.11
15/32 11.91
12
1/2 12.7
13
17/32 13.49
14
Technical Support 1-888-275-4538
service @mvpgroupcorp.com
3
Top of 737e
20104
20173
20716
20715
20713
20067
20732
20714
20718
4
temperature probe Wash Tank
Temperature probe rinse booster
Power line L1
Power line L2
Door switch signal
Water level signal
Booster Heat
Wash Heat
Incoming Water (chemicals) Drainage
Wash
Power Line L2
Final Rinse Probe
Touch-Pad
Wash Cycles
4m 3m 2m
Display
ON/OFF
Cycle Start
Unused Drain
5
ELECTRONIC BOARD PROGRAMMING
START
CBAD
MENU ACCESS
1 TURN THE MACHINE ON AND OFF BY PRESSING BUTTON A.
(IF THE MACHINE IS ALREADY ON, TURN IT OFF BY PRESSING BUTTON A)
2 PRESS BUTTON B SEVEN (7) TIMES WITHIN (10) SECONDS FROM TURNING OFF
MACHINE.
3 PRESS AND KEEP PRESSING BUTTON C ONCE QUICKLY.
“P-00 STOP” WILL BE ON THE DISPLAY.
MODIFY PARAMETERS
1 SELECT A PARAMETER BY SCROLLING THROUGH THE MENU WITH BUTTON B.
2 PRESS BUTTON C TO ENTER INTO THE PARAMETER MODIFICATION.
3 PRESS BUTTON B TO MODIFY THE PARAMETER WITH AVAILABLE OPTIONS
AND BUTTON C TO CONFIRM THE MODIFICATION.
ONCE YOU CONFIRM THE MODIFICATION, YOU RETURN TO POINT 1 WITH THE OPTION TO
SELECT ANOTHER PARAMETER BY SCROLLING THROUGH THE MENU WITH BUTTON B.
Level 1
Level 1 access will allow you to change the first 4 settings.
6
P-00
STOP
P-01
T-BL
P-02
T-VA
P-03
SOFT
Thermostop
0= not active
1=active
default:0
Temperature boiler
Min 60C 140F
Max 95C 200F
Default 85C 185F
Temperature Tank
Set to 70C 160F
Default 60C 140F
Soft start
0= not active
1= active
default: 1 ,set to 0
AVAILABLE PARAMETERS
MAX HEATING TANK
Min 1 min
Max 60 min
∗DEFAULT 45 min
DON’T MODIFY
TEMPERATURE UNITS
FAR = FAHRENHEIT
CEL = CELSIUS
∗DEFAULT CEL=CELSIUS
OFFSET TEMPERATURE TANK
Min - 20°C
Max +20°C
∗DEFAULT 0°C
DON’T MODIFY
MAX HEATING BOILER
Min 5 min
Max 60 min
∗DEFAULT 30 min
DON’T MODIFY
REAL TEMPERATURE
0 = FILTERED
1 = REAL
∗DEFAULT 0 = FILTERED
DON’T MODIFY
MAX LOADING TANK
Min 1 min
Max 20 min
∗DEFAULT 10 min
DON’T MODIFY
MAX DRAIN TANK
Min 1 min
Max 20 min
∗DEFAULT 2 min
DON’T MODIFY
TEMPERATURE BOILER
Min 60°C
Max 95°C
∗DEFAULT 85°C
TEMPERATURE TANK
Min 40°C
Max 65°C
∗DEFAULT 60°C
TYPE MACHINE
Min 1
Max 2
∗DEFAULT SEE CHART
SOFT START
0 = not active
1 = active
∗DEFAULT 1=ACTIVE
OFFSET TEMPERATURE BOILER
Min - 20°C
Max +20°C
∗DEFAULT 0°C
THERMOSTOP
0 = not active
1 = active
∗DEFAULT 0=NOT ACTIVE
MODEL MACHINE
Min 1
Max 27
∗DEFAULT SEE CHART
P04
(DISPLAY)
P05
(DISPLAY)
MODEL
CYCLE
DRAIN PUMP
2 8
4 31 70 + 120 + 180 + 240 sec
757E
120 + 180 + 240 sec YES
727E / 737E
7
1 TURN THE MACHINE ON AND OFF BY PRESSING BUTTON A.
(IF THE MACHINE IS ALREADY ON, TURN IT OFF BY PRESSING BUTTON A)
2 PRESS BUTTON B SEVEN (7) TIMES WITHIN (10) SECONDS
FROM TURNING OFF MACHINE.
3 PRESS AND KEEP PRESSING BUTTON C FOR THREE (3) SECONDS
UNTIL P-00 STOP IS ON THE DISPLAY.
Level 2
Level 2 access will allow you to change all 14 settings.
P-04
TIPO
P-05
MODL
P-06
O-BL
P-07
O-VA
TYPE OF MACHINE
SET AT 2
MODEL OF MACHINE
SET AT 8
OFFSET
TEMPERATURE BOILER
! DO NOT CHANGE
SET AT 0
OFFSET
TEMPERATURE TANK
! DO NOT CHANGE
SET AT 0
PP-0
P-01
P-02
P-03
P-08
REAL
P-09
FARH
A-00
N-BL
A-01
N-VA
REAL TEMPERATURE
0= FILTERED
1= ACTUAL
DEFAULT=0
TEMPERATURE UNIT
0=CELSIUS
1= FAHRENHEIT
SET TO 1
MAX HEATING TIME
FOR BOILER
MIN 5 MIN
MAX 60 MIN
DEFAULT 30 MIN
MAX HEATING TIME
FOR TANK
MIN 1 MIN
MAX 60 MIN
DEFAULT 45MIN
8
A-02
CARL
A-03
VUOT
MAX FILL TIME
MIN 1 MIN
MAX 20 MIN
DEFAULT 10 MIN
MAX DRAIN TIME
MIN 1 MIN
MAX 20 MIN
DEFAULT 2 MIN
ntcb
E-01
Booster temperature probe faulty or not connected properly
ntcu
E-02
Tank temperature probe faulty or not connected properly
FILL
E-03
Water fill not completed within allocated time (10 min)
Obstruction in water line, or faulty solenoid valve.
t bo
E-04
Booster temperature limit setpoint reached (+14C/ 57F)
t UA
E-05
Tank temperature limit setpoint reached (+14C/57F)
drA
E-06
Drain problem; Drainage not completed on maximum set time.
Bad drain pump, obstruction in drain line or pump.
bnot
E-07
Maximum booster heating time reached (15min)
unot
E-08
maximum tank heating time reached (30 min)
SErulCE
E-09
Memory error or electronic board damaged
Error Codes
9
-PS-
d--1
-PL-
d--1
88:88
empty
-r r-
0143
Drain pump test
door closed
d--0 = door open
Wash pump test
door closed
N/A
SALT
OPEN
-rb-
0078
empty
88:88
-rL-
0046
N/A
Booster heater test
temperature in Celsius
Wash Tank Heater test
Temperature in Celsius
-EC-
d--1
-ER-
d--1
-Er-
d--1
-Eb-
d--1
P-10
door closed
P-13
door closed
P-25
door closed
Solenoid valve
(chemical pumps) test
door closed
1 TURN THE MACHINE ON AND OFF BY PRESSING BUTTON A.
(IF THE MACHINE IS ALREADY ON, TURN IT OFF BY PRESSING BUTTON A)
2 PRESS BUTTON C SEVEN (7) TIMES WITHIN (10) SECONDS
FROM TURNING OFF MACHINE.
Level 3
Level 3 access will allow you test different components.
10
Andere Handbücher für 737E
1
Inhaltsverzeichnis
Andere Jet-tech Spülmaschine Handbücher
Jet-tech
Jet-tech 747 Bedienungsanleitung
Jet-tech
Jet-tech 737E Bedienungsanleitung
Jet-tech
Jet-tech X-32 Bedienungsanleitung
Jet-tech
Jet-tech X-32 Bedienungsanleitung
Jet-tech
Jet-tech 727E Bedienungsanleitung
Jet-tech
Jet-tech X-33 Bedienungsanleitung
Jet-tech
Jet-tech X-33 Bedienungsanleitung
Jet-tech
Jet-tech XG-37 Bedienungsanleitung
Jet-tech
Jet-tech F-18 Bedienungsanleitung
Jet-tech
Jet-tech F 14 Bedienungsanleitung
