Jet LOAD-N-LOCK JT1-125 Bedienungsanleitung

LOAD-N-LOCK™UTILITY CART

SECURITY SYSTEM

MODELS: JT1-125, JT1-126

INSTALLATION MANUAL

Part No. M-JT1-125

Edition 2 07/2023

JET • LOAD-N-LOCK™ UTILITY CART SECURITY SYSTEM | 1

1Safety Information

2Tools Needed

Refer to Assembly Illustration (Figure 1) on Page 3

The following items are needed to properly and safely install

the LOAD-N-LOCK™ Utility Cart Security System panels.

• Approved eye protection

• Corded or cordless drill

• 7/32” drill bit

• 8mm socket or wrench

This product is NOT intended for the secure

storage of ALL materials. LOAD-N-LOCK™ Utility

Cart Security System panels provide signicantly

enhanced storage security, but may still be sub-

ject to resin cart structure and mobility vulnera-

bilities. Items such as rearms, other weapons,

combustible materials, and medication should not

be stored in this unit. Use common sense when

determining what items are stored in the cart and

what environment the cart will be used.

Reference the owner’s manual for the cart for

additional safety information about the safe use

and handling of the cart.

Be aware of the stated cart weight capacity due

to the added weight of the LOAD-N-LOCK™ Utility

Cart Security System panels.

Do not store fuel, ammable liquids and gases,

other ammable materials, or other hazardous

materials in the cart.

Make sure cart door is securely latched when

transporting.

Do not modify the LOAD-N-LOCK™ Utility Cart

Security System panels in any way. Modication

or unintended use of this product will void all

manufacturer warranty and could pose a hazard

to the user or others.

Use approved eye protection when drilling screw

holes.

2| Chapter 3: Assembly Instructions

3Assembly Instructions

Refer to Assembly Illustration (Figure 1) on Page 3

Before installation, consider which side on your cart you

want to install the front door panel and which side you want

to install the rear panel. Due to access and reach, you will

install the back panel rst, the side panels next, and the front

door panel last. When installing panels, lay the resin cart on

protective material, such as cardboard.

Step 1: Installing Back Panel

1. Choose the side of the cart where you want the front

door panel installed and lay that side down on protective

material. The side of the cart you want the back panel

installed should be facing up.

2. Lay the panel in place on the cart. Make sure the panel

is centered side to side within the opening. Push the

panel to the top of the cart opening.

3. There should be equal gaps between the panel and the

cart at the top, left to right, and at the bottom, left to

right. If the panel t does not result in equal gaps, plan

to square the cart to t the panel as much as possible. If

attempting to square the cart, during step 4 below, drill

and install one top corner carriage bolt rst. Apply pres-

sure to the cart to create equal gaps and drill and install

the second carriage bolt diagonally across to the lower

corner on the opposite side. Drill and install remaining

carriage bolts as instructed in step 4 below.

4. With the panel in place, use a 7/32” drill bit and match-

drill the six carriage bolt locations along the panel sides.

Take care to drill the center of the bolt location and don’t

allow the drill bit to slide to the side before biting into

the cart material. Make sure to drill all the way through

to the cart material.

5. Insert six M5 x 20mm carriage bolts through the panel

and cart. Attach the carriage bolts using six 5mm wash-

ers and six 5mm external-tooth lock nuts. Tighten nuts

rmly using 8mm socket. NOTE: Press each carriage bolt

neck into the slot/hole and against the panel. Use pres-

sure, a weight, or temporary tape to keep the carriage

bolts in place while installing the washers and nuts.

Step 2: Installing Side Panels

1. Turn the cart 90-degrees on protective material to ex-

pose one of the side panel locations.

2. Repeat steps 2 through 5 under “Installing Back Panel”

to install the rst side panel.

3. Turn the cart 180-degrees on protective material so the

opposite side panel location is facing up.

4. Repeat steps 2 through 5 under “Installing Back Panel”

to install the nal side panel.

Step 3: Installing Front Door Panel

1. Lay the back panel side of the cart down on protective

material. The side of the cart for the front door panel

should be facing up.

2. Lay the front door panel in place on the cart as shown

in Figure 1. Cut the zip tie to release the latch. Rotate

the latch to allow the front door panel to rest at against

the cart. Make sure the panel is centered side to side

within the opening. Push the panel to the top of the cart

opening.

3. With the panel in place, use a 7/32” drill bit and match-

drill the ten carriage bolt locations along the panel sides,

upper strut, and lower strut. Take care to drill the center

of the bolt location and don’t allow the drill bit to slide to

the side before biting into the cart material. Make sure to

drill all the way through the cart material.

JET • LOAD-N-LOCK™ UTILITY CART SECURITY SYSTEM | 3

Installing LOAD-N-LOCK™ Utility Cart Security System Panels - Assembly Illustration

4. Model JT1-125: After drilling holes, insert ten M5 x

25mm carriage bolts. Open both doors completely and

allow them to rest on the carriage bolt heads. Attach

the 5mm washers and 5mm external-tooth lock nuts for

the side and bottom bolt locations. Firmly tighten these

nuts. Stand the cart onto its wheels and attach the 5mm

washers and 5mm nuts onto the two carriage bolts

located above the hinges. Tighten rmly.

Model JT1-126: After drilling holes, insert six M5 x

25mm carriage bolts along the sides of the panel. Insert

four M5 x 30mm carriage bolts in the top and bottom

locations. Open both doors completely and allow them to

rest on the carriage bolt heads. Attach the 5mm wash-

ers and 5mm external-tooth lock nuts for the side and

bottom bolt locations. Firmly tighten these nuts. Stand

the cart onto its wheels and attach the 5mm washers

and 5mm nuts onto the two carriage bolts located above

the hinges. Tighten rmly.

Figure 1: Installing LOAD-N-LOCK™ Utility Cart Security System Panels

Model Number: ______________________

Date Purchased: ______________________

Where Purchased: ______________________

4Warranty

JET warrants every product it sells against manufacturers’ defects.

If one of our tools needs service or repair, please contact Technical

Service by calling 1-800-274-6846, 8AM to 5PM CST, Monday

through Friday.

Warranty Period

The general warranty lasts for the time period specied in the

literature included with your product or on the ofcial JET branded

website.

• JET products carry a limited warranty which varies in dura-

tion based upon the product. (See chart below)

• Accessories carry a limited warranty of one year from the

date of receipt.

• Consumable items are dened as expendable parts or

accessories expected to become inoperable within a rea-

sonable amount of use and are covered by a 90 day limited

warranty against manufacturer’s defects.

Who is Covered

This warranty covers only the initial purchaser of the product from

the date of delivery.

What is Covered

This warranty covers any defects in workmanship or materials sub-

ject to the limitations stated below. This warranty does not cover

failures due directly or indirectly to misuse, abuse, negligence or

accidents, normal wear-and-tear, improper repair, alterations or

lack of maintenance. JET woodworking machinery is designed to

be used with Wood. Use of these machines in the processing of

metal, plastics, or other materials outside recommended guide-

lines may void the warranty. The exceptions are acrylics and other

natural items that are made specically for wood turning.

Warranty Limitations

Woodworking products with a Five Year Warranty that are used for

commercial or industrial purposes default to a Two Year Warranty.

Please contact Technical Service at 1-800-274-6846 for further

clarication.

How to Get Technical Support

Please contact Technical Service by calling 1-800-274-6846.

Please note that you will be asked to provide proof of initial

purchase when calling. If a product requires further inspection,

the Technical Service representative will explain and assist with

any additional action needed. JET has Authorized Service Centers

located throughout the United States. For the name of an Autho-

rized Service Center in your area call 1-800-274-6846 or use the

Service Center Locator on the JET website.

More Information

JET is constantly adding new products. For complete, up-to-date

product information, check with your local distributor or visit the

JET website.

How State Law Applies

This warranty gives you specic legal rights, subject to applicable

state law.

Limitations on This Warranty

JET LIMITS ALL IMPLIED WARRANTIES TO THE PERIOD OF THE LIM-

ITED WARRANTY FOR EACH PRODUCT. EXCEPT AS STATED HEREIN,

ANY IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS

FOR A PARTICULAR PURPOSE ARE EXCLUDED. SOME STATES DO

NOT ALLOW LIMITATIONS ON HOW LONG AN IMPLIED WARRANTY

LASTS, SO THE ABOVE LIMITATION MAY NOT APPLY TO YOU.

JET SHALL IN NO EVENT BE LIABLE FOR DEATH, INJURIES TO PER-

SONS OR PROPERTY, OR FOR INCIDENTAL, CONTINGENT, SPECIAL,

OR CONSEQUENTIAL DAMAGES ARISING FROM THE USE OF OUR

PRODUCTS. SOME STATES DO NOT ALLOW THE EXCLUSION OR

LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES, SO

THE ABOVE LIMITATION OR EXCLUSION MAY NOT APPLY TO YOU.

JET sells through distributors only. The specications listed in JET

printed materials and on ofcial JET website are given as general

information and are not binding. JET reserves the right to effect at

any time, without prior notice, those alterations to parts, ttings,

and accessory equipment which they may deem necessary for any

reason whatsoever. JET® branded products are not sold in Canada

by JPW Industries, Inc.

Product Listing with Warranty Period

90 Days – Parts; Consumable items

1 Year – Motors; Machine Accessories

2 Year – Metalworking Machinery; Electric Hoists, Electric

Hoist Accessories; Woodworking Machinery used for industrial

or commercial purposes

5 Year – Woodworking Machinery

Limited Lifetime – JET Parallel clamps; VOLT Series Electric

Hoists; Manual Hoists; Manual Hoist; Accessories; Shop Tools;

Warehouse & Dock products; Hand Tools: Air Tools

NOTE: JET is a division of JPW Industries, Inc. References in this

document to JET also apply to JPW Industries, Inc., or any of its

successors in interest to the JET brand.

Chapter 4: Warranty

JET • LOAD-N-LOCK™ UTILITY CART SECURITY SYSTEM | 6

JET

427 New Sanford Road

La Vergne, TN 37086

800-274-6848

www.jettools.com

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Jet Sicherheitssystem Handbücher

Jet

Jet WiFi Messenger Alarm Bedienungsanleitung

Beliebte Sicherheitssystem Handbücher anderer Marken

Inner Range

Inner Range Concept 2000 Bedienungsanleitung

Climax

Climax Mobile Lite R32 Montageanleitung

CADDX

CADDX NX-6 Bedienungsanleitung

FBII

FBII XL-31 Series Bedienungsanleitung

Johnson Controls

Johnson Controls PENN Connected PC10 Bedienungsanleitung

Aeotec

Aeotec Siren Gen5 Bedienungsanleitung

Blaupunkt

Blaupunkt SA 2700 Bedienungsanleitung

IDEAL

IDEAL Accenta Betriebsanleitung

AJAX

AJAX DoubleButton Bedienungsanleitung

Swann

Swann SW-P-MC2 Bedienungsanleitung

Ecolink

Ecolink Siren+Chime Bedienungsanleitung

Digital Monitoring Products

Digital Monitoring Products XR150 Bedienungsanleitung

EDM

EDM Solution 6+6 Wireless-AE Bedienungsanleitung

Highway Safety Group

Highway Safety Group EA401 Bedienungsanleitung

Siren

Siren LED GSM Bedienungsanleitung

Detection Systems

Detection Systems 7090i Montageanleitung

Se-Kure Controls

Se-Kure Controls MicroMini SK-4841 Bedienungsanleitung

Siemens

Siemens FDM273 Bedienungsanleitung