Jet AFS-1000B Service-Handbuch

Operating Instructions and Parts Manual

AFS-1000B Air Filtration System

JET

427 New Sanford Road

LaVergne, Tennessee 37086 Part No. M-708620B

Ph.: 800-274-6848 Revision C 09/2018

IMPORTANT SAFETY

INSTRUCTIONS

WARNING – To reduce risk of injury:

1. FOR YOUR OWN SAFETY, READ

INSTRUCTION MANUAL BEFORE

OPERATING THE TOOL. Learn the tool’s

application and limitations as well as the

specific hazards peculiar to it.

2. KEEP GUARDS IN PLACE and in working

order.

3. ALWAYS WEAR EYE PROTECTION.

4. GROUND ALL TOOLS. If tool is equipped

with three prong plug, it should be plugged into

a three-hole electrical receptacle. If an adapter

is used to accommodate a two prong

receptacle, the adapter lug must be attached

to a known ground. Never remove the third

prong.

5. KEEP WORK AREA CLEAN. Cluttered areas

and benches invite accidents.

6. DON’T USE IN DANGEROUS

ENVIRONMENT. Don’t use power tools in

damp or wet locations, or expose them to rain.

Keep work area well-lighted.

7. KEEP CHILDREN AND VISITORS AWAY. All

children and visitors should be kept a safe

distance from work area.

8. MAKE WORKSHOP CHILDPROOF. Use

padlocks, master switches, or remove starter

keys.

9. DON’T FORCE TOOL. It will do the job better

and be safer at the rate for which it was

designed.

10. USE RIGHT TOOL. Don’t force tool or

attachment to do a job for which it was not

designed.

11. WEAR PROPER APPAREL. No loose

clothing, gloves, neckties, rings, bracelets, or

other jewelry to get caught in moving parts.

Nonslip footwear is recommended. Wear

protective hair covering to contain long hair.

12. ALWAYS USE SAFETY GLASSES. Wear

safety glasses (must comply with ANSI Z87.1).

Everyday eyeglasses only have impact

resistant lenses; they are not safety glasses.

Also use face or dust mask if cutting operation

is dusty.

13. SECURE WORK. Use clamps or a vise to

hold work when practical. It’s safer than using

your hands and frees both hands to operate

tool.

14. DON’T OVERREACH. Keep proper footing

and balance at all times.

15. MAINTAIN TOOLS IN TOP CONDITION.

Keep tools sharp and clean for best and safest

performance. Follow instructions for lubricating

and changing accessories.

16. DISCONNECT TOOLS before servicing and

when changing filters.

17. USE RECOMMENDED ACCESSORIES. The

use of accessories and attachments not

recommended by manufacturer may cause

hazards or risk of injury to persons.

18. AVOID ACCIDENTAL STARTING. Make sure

switch is in “OFF” position before plugging in

power cord.

19. NEVER STAND ON TOOL. Serious injury

could occur if the tool is tipped or if the fan

blade is accidentally contacted.

20. CHECK DAMAGED PARTS. Before further

use of the tool, a guard or other part that is

damaged should be carefully checked to

ensure that it will operate properly and perform

its intended function-check for alignment of

moving parts, binding of moving parts,

breakage of parts, mounting, and any other

conditions that may affect its operation. A

guard or other part that is damaged should be

properly repaired or replaced.

21. NEVER LEAVE TOOL RUNNING

UNATTENDED. TURN POWER OFF. Don’t

leave tool until it comes to a complete stop.

22. DRUGS, ALCOHOL, MEDICATION. Do not

operate tool while under the influence of drugs,

alcohol or any medication.

23. MAKE SURE TOOL IS DICONNECTED

FROM POWER SUPPLY while motor is being

mounted, connected or reconnected

WARNING: This product can expose you to

chemicals including lead which is known to the

State of California to cause cancer and birth

defects or other reproductive harm. For more

information go to http://www.p65warnings.ca.

gov.

WARNING: Drilling, sawing, sanding or

machining wood products generates wood dust

and other substances known to the State of

California to cause cancer. Avoid inhaling dust

generated from wood products or use a dust

mask or other safeguards for personal

protection.

Wood products emit chemicals known to the

State of California to cause birth defects or

other reproductive harm. For more information

go to http://www.p65warnings.ca. gov/wood.

Table of Contents

IMPORTANT SAFETY INSTRUCTIONS .............................................................................................................. 2

Table of Contents .................................................................................................................................................. 3

Electrical Requirements ........................................................................................................................................ 4

Specifications ........................................................................................................................................................ 5

For Your Own Safety ............................................................................................................................................. 5

Contents of Shipping Carton ............................................................................................................................. 6

Tools Required for Assembly ............................................................................................................................ 6

Assembly ........................................................................................................................................................... 6

Controls and Features ....................................................................................................................................... 7

Changing the Filters .......................................................................................................................................... 8

Replacement Parts ................................................................................................................................................ 9

Parts List for the AFS-1000B Air Filtration System ......................................................................................... 10

AFS-1000B Wiring Diagram ................................................................................................................................ 11

Warranty and Service .......................................................................................................................................... 12

Electrical Requirements

In the event of a malfunction or breakdown, grounding provides a path of least resistance for electric current to

reduce the risk of electric shock. This tool is equipped with an electric cord having an equipment-grounding

conductor and a grounding plug. The plug must be plugged into a matching outlet that is properly installed and

grounded in accordance with all local codes and ordinances.

Do not modify the plug provided. If it will not fit the outlet, have the proper outlet installed by a qualified

electrician.

Improper connection of the equipment-grounding conductor can result in a risk of electric shock. The

conductor, with insulation having an outer surface that is green with or without yellow stripes, is the equipment-

grounding conductor. If repair or replacement of the electric cord or plug is necessary, do not connect the

equipment-grounding conductor to a live terminal.

Check with a qualified electrician or service personnel if the grounding instructions are not completely

understood, or if in doubt as to whether the tool is properly grounded.

Use only three wire extension cords that have three-prong grounding plugs and three-pole receptacles that

accept the tool’s plug.*

Repair or replace a damaged or worn cord immediately.

This tool is intended for use on a circuit that has an outlet that looks the one illustrated in Figure A below. The

tool has a grounding plug that looks like the grounding plug as illustrated in Figure A below. A temporary

adapter, which locks like the adapter as illustrated in Figures B below, may be used to connect this plug to a

two-pole receptacle, as shown in Figure B if a properly grounded outlet is not available.** The temporary

adapter should only be used until a properly grounded outlet can be installed by a qualified electrician. The

green colored rigid ear or tab, extending from the adapter, must be connected to a permanent ground such as

a properly grounded outlet box.

* Canadian electrical codes require extension cords to be certified SJT type or better.

** Use of an adapter in Canada is not acceptable.

Specifications

Model Number ...................................................................................................................................... AFS-1000B

Stock Number ........................................................................................................................................... 708620B

Outer Filter .............................................................................................................................................. 5 Microns

Inner Filter ................................................................................................................................................. 1 Micron

Overall Dimensions (LxWxH/in) ........................................................................................ 30-1/4 x 24-1/8 x 12-1/8

Sound Rating @ 3ft .................................................................................................................... High Speed 69 dB

............................................................................................................................................. Medium Speed 67 dB

.................................................................................................................................................... Low Speed 62 dB

Air Flow .............................................................................................................................. High Speed 1044 CFM

........................................................................................................................................ Medium Speed 702 CFM

.............................................................................................................................................. Low Speed 556 CFM

Filter Cycle (min.) ............................................................................................................................................. 3.06

Cycles per Hour (20’x20’x8’) .......................................................................................................................... 19.58

Motor ............................................................................................................. 1/5 HP, 115V, 60Hz, 1 PH, 6P, 4.5A

Net Weight ................................................................................................................................................... 54 lbs.

Shipping Weight ........................................................................................................................................... 61 lbs.

For Your Own Safety

1. Read and understand instruction manual before installing or operating air cleaner.

2. To reduce the risk of injury disconnect the air cleaner from the power source (unplug) before servicing

or changing filters.

3. If ceiling mounted, bottom of air cleaner must be at least 7 feet above the floor.

4. If ceiling mounted, mounts must be anchored to building structure which will support a minimum of at

least 100 pounds. Never mount to surfaces such as dry wall or false ceiling grids, etc.

5. To reduce the risk of electrical shock, do not expose air cleaner to water or rain.

6. Never duct a machine directly into the air cleaner.

7. To avoid a potentially dangerous situation, do not use this equipment to filter flammable vapors or

smoke. This air cleaner is designed and intended for the filtration of air borne wood dust only. It is

neither designed nor intended for any other purpose whatsoever.

8. Failure to comply may result in serious injury and / or property damage.

The above specifications were current at the time this manual was published, but because of our policy of

continuous improvement, JET reserves the right to change specifications at any time and without prior notice,

without incurring obligations.

Contents of Shipping Carton

1 Air Filtration Unit

1 Remote Control

3 AAA Batteries

4 Eye Bolts and Nuts

4 Mounting Brackets

8 Hex Cap Screws

8 Lock Washers

4 Foam Pads

1 Velcro Pad

1 Manual and Warranty Card

Tools Required for Assembly

No. 2 Cross Point Screwdriver

10mm Wrench

 The air filtration unit does not require much

assembly. You should take into consideration

how and where you will place this unit.

 It can be mounted horizontally and vertically.

The unit can also be hung from the ceiling.

 This unit will work best if it is located away from

corners, and heating/cooling vents.

 If using on sawhorses the air filtration unit should

be clamped in place.

 This unit is specifically designed to circulate and

filter non-metallic dust, which is generated

throughout the work area.

Assembly

Mounts must be anchored to

building structure, which will support a

minimum of at least 100 pounds. Never mount

to surfaces such as dry wall, false ceiling grids,

etc.

1. Remove all packing from inside of the unit by

removing the outer filter and inner filters.

2. The air filtration unit can be hung from the

ceiling. Remove four screws from the cabinet

top (A, Fig. 1).

3. Hang the unit using four eyebolts (B, Fig. 1),

and four hex nuts (C, Fig. 1) provided.

Figure 1

4. The lock nut needs to be threaded almost all

the way up the eyebolt. Screw the eye bolt into

the hole and tighten lock nut against the

cabinet top. You will need to hold the eyebolt

so it does not spin while tightening the lock

nut.

5. Repeat steps for remaining three eyebolts.

Note: Make sure chain and ceiling hooks are

properly rated for hanging this unit. Hang unit with

a seven-foot clearance from the floor.

Figure 3 shows the mounting hole centers.

Mounts must be anchored to

building structure, which will support a

minimum of at least 100 pounds. Never mount

to surfaces such as dry wall or false ceiling

grids, etc.

Four brackets can also be used for mounting to the

ceiling, or wall:

1. Place one end of bracket underneath the lip of

the cabinet.

2. Attach the bracket (A, Fig. 2) with two hex cap

screws (B, Fig. 2) and two lock washers (C,

Fig. 2).

3. Repeat steps for remaining three brackets.

4. Peel off the paper backing from the foam

pads, and stick the pads to the bottom side of

the machine’s four corners.

Controls and Features

Remote Control:

Time button (A, Fig. 4) controls the three different

settings.

2H will light up on the back of the unit with one

press of the time button. The air filtration system

will operate for 2 hours then shut off.

4H will light up on the back of the unit by pressing

the time button twice. The air filtration system will

operate for 4 hours then shut off.

8H will light up on the back of the unit by pressing

the time button three times. The air filtration

system will operate for 8 hours then shut off.

Speed button (B, Fig. 4) controls the three different

settings, Low, Medium and High. There is also a

manual button (A, Fig. 5) on the backside of this

unit which controls the speed.

Figure 2

Figure 3

Figure 4

On/Off button (C, Fig. 4) turns the unit on and off.

There is also a manual on/off button (B, Fig. 5) on

the backside of the unit. Pressing this button will

turn the machine on Low.

Fuse switch (C, Fig. 5) will pop out in the case of

overload. Wait 3-5 minutes and push the fuse in.

Changing the Filters

To reduce the risk of injury,

disconnect the air cleaner from the power

source (unplug) before servicing or changing

filters. Failure to comply may cause serious

injury!

There are two filters that need to be changed. The

outer filter can easily be removed by disengaging

the two clips (A, Fig. 7).

Now you can simply pull the filter out, or use a

screwdriver to pop the filter out.

The inner filter (A, Fig. 7) can now be pulled out of

the unit. The inner filter can be blown out with

compressed air.

The filters should be replaced depending on the

amount of usage and the environment of your

shop. Clogged filters will reduce the amount of air

circulation. There is an arrow indicating the air

flow direction on the outer filter. Make sure the

filter is inserted facing the proper direction.

Replacement Filters

708731 electrostatic outer filter

708732 washable electrostatic outer filter

708733 inner filter

708734 charcoal filter

Figure 5

Figure 6

Figure 7

Replacement Parts

To order parts or reach our service department, call 1-800-274-6848, Monday through Friday (see our website

for business hours, www.jettools.com). Having the Model Number and Serial Number of your machine available

when you call will allow us to serve you quickly and accurately.

Parts List for the AFS-1000B Air Filtration System

Index No. Part No. Description Size Qty

1 ................ 708731 ...................... Electrostatic Outer Filter .......................................... ...................................... 1

2 ................ 708733 ...................... Inner Three-Pocket Filter ......................................... ...................................... 1

4 ................ AB001008 ................. Door Clip Set ........................................................... ...................................... 2

5 ................ AB001108W .............. Air Box ..................................................................... ...................................... 1

6 ................ SJ069300 .................. Pan Head Bolt ......................................................... M6x12 ........................... 6

7 ................ OO1033 ..................... Switch Wire w/Terminal ........................................... ...................................... 1

8 ................ NH050800 ................. Nut ........................................................................... M5 ................................. 2

9 ................ WE050000 ................ Star Washer ............................................................. M5 ................................. 2

10 .............. OO1022W ................. Switch Plate ............................................................. ...................................... 1

.................. AB001022W .............. Switch Plate Set (assembly not shown)................... ........................................

11 .............. SP059300 ................. Pan Head Bolt ......................................................... M5x12 ........................... 1

12 .............. IC001015 ................... Electric Wire............................................................. ...................................... 1

13 .............. 998623 ...................... Strain Relief ............................................................. ...................................... 1

14 .............. 330075 ...................... 5A Thermos Switch.................................................. ...................................... 1

15 .............. 10042 ........................ Nut ........................................................................... M6 ................................. 4

16 .............. 330006 ...................... Sleeve ...................................................................... ...................................... 4

17 .............. 330005 ...................... Spacer ..................................................................... ...................................... 4

20 .............. WF061310 ................. Flat Washer ............................................................. M6 ................................. 6

21 .............. ST049200 .................. Tapping Screw ......................................................... M4x8 ............................. 2

22 .............. SR089400 ................. Hex Socket Bolt ....................................................... M8x16 ........................... 1

23 .............. OO1055 ..................... Fan Blade ................................................................ ...................................... 1

24 .............. OO1056 ..................... Fan Housing ............................................................ ...................................... 1

25 .............. OO1057 ..................... Motor........................................................................ ...................................... 1

.................. CA001000B ............... Capacitor (not shown).............................................. ...................................... 1

26 .............. NF050800 ................. Nut ........................................................................... M5 ................................. 4

28 .............. 708711 ...................... Remote Control........................................................ ...................................... 1

29 .............. 330004 ...................... Flange ...................................................................... ...................................... 1

30 .............. 330043 ...................... PC Board ................................................................. ...................................... 1

31 .............. OO1023 ..................... Eye Bolt ................................................................... ...................................... 4

32 .............. NH061000 ................. Nut ........................................................................... M6 ................................. 4

33 .............. SN490200 ................. Counter Sunk Bolt ................................................... 1/8”x1/4” ........................ 3

34 .............. SP049100 ................. Pan Head Bolt ......................................................... M4x6 ............................. 4

35 .............. OO1029 ..................... Concave Handle ...................................................... ...................................... 2

36 .............. SR060600 ................. Hex Socket Bolt ....................................................... M6x30 ........................... 4

37 .............. WF061620 ................. Washer .................................................................... M6x16 ........................... 8

38 .............. LM000513 ................. I.D. Label ................................................................. ...................................... 1

39 .............. LM000344 ................. Remote Label .......................................................... ...................................... 1

40 .............. 990638 ...................... Wiring Nut ................................................................ P2 ................................. 1

41 .............. SF069200 .................. Rivet Nut .................................................................. M6x8 ............................. 4

42 .............. 330074 ...................... Pad .......................................................................... ...................................... 4

43 .............. TS-1551041 .............. Spring Washer ......................................................... M6 ................................. 6

44 .............. OO1027 ..................... Hanger Plate ............................................................ ...................................... 4

45 .............. SH069200 ................. Hex Head Bolt.......................................................... M6x8 ............................. 8

46 .............. TS-1551041 .............. Spring Washer ......................................................... M6 ................................. 8

.................. OO1045 ..................... Color Stripe (not shown) .......................................... ...................................... 1

.................. AH001103 ................. Hardware Kit (includes index # 28,31,32,37,42) ...... ...................................... 1

.................. LM000280 ................. JET Air Filtration I.D. Label (not shown: side of cabinet) ................................ 2

.................. LM000210 ................. Warning Label (not shown) ...................................... ...................................... 1

Replacement Filters:

.................. 708731 ...................... Electrostatic Outer Filter

.................. 708732 ...................... Washable Electrostatic Outer Filter

.................. 708733 ...................... Inner Three-Pocket Filter

.................. 708734 ...................... Charcoal Filter

Andere Handbücher für AFS-1000B

Inhaltsverzeichnis

Andere Jet Wasserfiltersystem Handbücher