Jetmaster QUADRO 1050 Bedienungsanleitung

IMPORTANT: Read all instructions carefully before starting installation. Failure to follow these instructions

may result in afire hazard and will void the warranty.

Due to continued product improvement, The Fireplace Ltd reserves the right to change product specifications without prior notification.

Please check to ensure you have the latest installation instructions.

TYPICAL JETMASTER IN-BUILT TIMBER FRAME & MASONRY

FIREBOX INSTALLATION INSTRUCTIONS FOR

QUADRO OUTDOOR WOOD FIRE & BBQ GRILL

08/2022 1

CONTENTS

Before you start - IMPORTANT…………………………

Firebox Dimensions ………………………………………

Timber Cavity Framing Dimensions ………………......

Timber Frame Plan & Section ………………………….

Hebel Cell Diagram ………………………………………

Front Face Margin ……………………………………...

Firebox Installation……………………………………….

Masonry Cavity Plan & Section …………………….…

Firebox Installation and Margins………………….…….

Flue Installation …………………………………………..

Flue Penetration & Chimney Chase Air Ventilation…..

Floor Protector requirements …………………………….

Hebel Cut Out Schedule…………………………….

HeadOffice &Showroom

12 Tawari St, Mt Eden,Auckland

Ph: 09 623 6990

thefireplace.co.nz

AS/NZS2918:2001 GENERAL NOTES – SOLID FUEL

THE APPLIANCE AND FLUE SYSTEM SHALL BE INSTALLED IN ACCORDANCE WITH AS/NZS2918:2001

AND THE APPROPRIATE REQUIREMENTS OF THERELEVANT BUILDING CODE OR CODES.

MIXING OF APPLIANCE OR FLUE SYSTEM COMPONENTS FROM DIFFERENT SOURCES OR

MODIFYING THE DIMENSIONAL SPECIFICATION OF COMPONENTS MAY RESULT IN HAZARDOUS

CONDITIONS. WHERE SUCH ACTION IS CONSIDERED, THE MANUFACTURER SHOULD BE

CONSULTED IN THE FIRST INSTANCE.

CRACKED AND BROKEN COMPONENTS, e.g. GLASS PANELS OR CERAMIC TILES, MAY RENDER THE

INSTALLATION UNSAFE.

DO NOT USE FLAMMABLE LIQUIDS OR AEROSOLS TO START OR REKINDLE THE FIRE OR IN THE

VICINITY OF THIS APPLIANCE WHEN OPERATING.

DO NOT STORE FUEL WITHIN HEATER INSTALLATION CLEARANCES.

WHEN OPERATING THIS APPLIANCE AS AN OPEN FIRE USE A FIRE SCREEN.

THIS APPLIANCE SHOULD BE MAINTAINED AND OPERATED AT ALL TIMES IN ACCORDANCE WITH

THESE INSTRUCTIONS.

USE OF SOME TYPES OF PRESERVATIVE-TREATED WOOD AS A FUEL CAN BE HAZARDOUS.

IF INSTALLED IN ACOMMERCIAL SETTING ASACRIFICIAL PLATE MUST BE FITTED TO THE BACK

OF THE FIRE TO COMPLY WITH JM FIREBOX WARRANTY CONDITIONS.

THE FLUE SYSTEM SHOULD BE CLEANED EVERY 12 MONTHS.

AS/NZS2918:2001 GENERAL NOTES –SOLID FUEL

AS/NZS5601:2013GENERAL NOTES –GAS

THE JETMASTER UNIT IS TO BE INSTALLED BY ACERTIFIED FIREPLACE

INSTALLER , APPROVED NZHHA INSTALLATION TECHNICIAN

IMPORTANT

CAVITY FRAMING A B C D E F

1050 1400 800 500 850 2 x 160 dia. or 2 x (100 x200) 1275 height of Hebel cell

Timber frame-out with 75mm Hebel cell on a steel base.

IMPORTANT: If the firebox is raised it must be placed on

top of a 75mm Hebel panel which is placed on top of a

steel structure or masonry blocks.

A TIMBER BASE IS NOT ACCEPTABLE

Please note that these dimensions (based on Hebel

Block margins) are the absolute minimum sizes -widths

(A &B) maybe increased if desired.

Table 2

TIMBER FRAME DIMENSIONS

JETMASTER FIREBOX DIMENSIONS

Table 1

Note: All dimensions are in (mm)

min 2 x 160mm dia. or equal square or rectangle shaped

air vents to be wall mounted

Hebel

Maximum 100mm recess

Floor Protector (refer to Table 5)

800mm +recess

value (refer to

Table 2)

1400mm

Non Combustible material

(e.g Promatect H)

100

min

Flue Pipe Casing

S/S Flue Pipe

Hebel

Rock Wool

Insulation

Hebel Block

Non Combustible material

(e.g Promatect H)

Maximum 100mm recess

Secure firebox with 2 x12mm

dynabolts for earthquake

retraints

Maintain the air intake

unobstructed

Floor Protector

C(see Table 2)

Note: All external air vents must be bird & rodent

proofed with permanently fixed screen

Rebate to suit tiles or other non

combustible material on Floor

Protector

It is important to ensure the Jetmaster firebox is seated at the

required finished Floor Protector level

see Table 5

min 25mm from flue pipe casing to combustible material

25 25

Drawing Not To ScaleDrawing Not To Scale

Optional

Finishing:

Stone, Brick,

Plaster on

Brick

min 2 x 160mm dia

or equal square or

rectangle shaped air

vents to be wall

TIMBER FRAME CROSS SECTION -RECESS

DETAIL

TIMBER FRAME PLAN -RECESS

DETAIL

Note:If the appliance is exposed not under protective cover please recess the appliance

.Min =40mm/Max recess =100mm

Rock Wool

Insulation

(Glue rock wool

using fire cement

to the firebox &

gather)

All Hebel Block margins have been made to fit firebox timber frame trim out dimensions (see

Hebel cut-out plan). Suggested method to cut Hebel Block -skill saw fitted with masonry

blade.

Under no circumstance is the width of the vertical margin legs to be less than 150mm and the

height of the margin lintel to be less than 300mm

Where aboard finish is required around the fire, ensure allowance is made to place non combustible

internal wall lining (eg:Promatect H) to cover the extent of the Hebel panel surround (shown shaded).

Directly touching the firebox with any board or plaster finish will cause cracking from heat expansion.

Allow 2mm minimum space away from the firebox.

J et ma st er

Margin Lintel

min 300mm

Timber Framing

75mm min Hebel Block or

100mm Concrete

Note:Ensure allowance

made for firebox to sit

on top of finished Floor

Protector level

Margin leg to be no less than

150mm wide

Bond Hebel Block together using appropriate adhesive eg: Gorilla Grip or

similar (non-solvent based) &secure with screws for added strength

MARGIN SET

Non Combustible Board

Refer to the minimum framing dimensions as per table 2. Allow atemporary lintel height (see table

2‘B’) from the finished floor protector level until the firebox and flue system is installed.Install front

nogs on edge to increase chimney chase dimension.

Ensure suitable air vents (2 x 160mm diameter or equivalent) in place to vent firebox space -these

maybe located in the floor or in the side wall space.Ensure vents must be bird and vermin proofed.

FIREBOX INSTALLATION

•All dimensions shown for the framing trim out and Hebel cell are based on a maximum

frontal clearance between the timber framing and the rear of the firebox fascia, being not

more than 15mm.

•Locate floor protector in trim out cavity. If on a concrete floor, suggest a mortar screed to the

underside of the floor protector. If on a wooden floor, screw or dynabolt in place.

•Locate stud openings on both sides.

•Position and ensure a strip of glass rock wool insulation is between the inner hebel leg face and

the firebox. Nail through stud into hebel leg to secure in place.

•Locate and position firebox, fit and seal gather in cavity. Earthquake restraints may be

positioned by drilling through firebox into the floor protector, in a position midway beneath the

log-pan. Two 12mm dynabolts or similar will suffice. Do not over tighten and deform firebox.

•Attach rock wool to the sides & back of the firebox and gather. DO NOT BLOCK OFF the air

entry between the inner flue pipe and flue pipe casing or the air circulation between the vent

holes in the cavity.

•Once the flue system is installed, place a minimum 300mm hebel block over the front face

of the firebox and gather.

•Ensure the hebel block does not rest on top of the firebox. A Lintel Bar may be required.

TIMBER FRAMING PREPARATION

IMPORTANT:The appliance must be located aminimum of 1200mm away from

combustible adjacent walls (e.g. exterior of house)

The appliance, gather, flue and Hebel panel weighs approx.400kg.Ensure the base

structure can withstand this load.

MODEL A B Temporary Lintel CDE -Vents

1050 1150 700 1200 100 860 2 x 160dia. or 2 x (100x

200)

Table 3

MASONRY MINIMUM CAVITY SIZE

Fig. 11

PLAN -RECESS DETAIL

min. 25mm clearance 25

25 min. 25mm clearance

700mm +recess

Masonry or Hebel block

minimum ‘A’

Refer to Table 5 for Floor Protector dimension

RECESS REQUIRED (40mm Min. 100mm Max)

Allow gas line into

firebox

(if applicable)

Air Vent

‘Refer to Table 5for Floor

Protector dimension

Air Vent

min. 2 x 100 x 50mm or 80mm diam

wall of floor mounted air vents

Drawings Not To Scale

Note:If the appliance is exposed not under protective cover please recess the appliance

.Min =40mm/Max recess =100mm. Add recess dimension to B dimension in Table 3.

100

700mm + recess

Allow 5mm gap

around all four

sides of the firebox

to fit Stainless

Steel cover & allow

for firebox

expansion

RECESS REQUIRED

40mm Min.

- 100mm Max recess

CROSS SECTION

min 2 x 160mm dia. or equal square or rectangle shaped

air vents to be wall mounted

FIREBOX INSTALLATION

1. Locate and position firebox, fit and seal gather in cavity using fire cement (exhaust cement) and

bolts (supplied), to the firebox.

2. Note:Poprivet back of gather to firebox if required (refer to Cross Section).Earthquake

restraints may be positioned by drilling through firebox into the floor protector, in aposition

midway beneath the log-pan.Two 6mm dynabolts or similar will suffice.Do not over tighten and

deform firebox.

2. Attach rock wool (supplied) to the sides of the firebox and gather (using fire cement).

3. DO NOT BLOCK OFF the air entry between the inner flue pipe and flue pipe casing or the air

circulation between the vent holes in the cavity.

3. Refer to Table 5, for minimum hearth sizes.

Aminimum 75mm thick Floor protector is only required if finished surface is combustible e.g:timber.

Please note that these dimensions (based on Masonry margins) are the absolute minimum sizes -

widths (A &B) maybe increased if desired.If you intend on recessing the firebox, please add the

recess value to Dimension ‘B’.

WARNING:Minimum cavity sizes leave NO MARGIN FOR ERROR .If the cavity is larger than

minimum dimensions (A &B) close up the lateral sides using Hebel block, concrete block

or similar (do not use any combustible material).

Refer to Tab l e 3for the minimum cavity dimensions and temporary lintel height measurements,

until the firebox and flue system is installed.Note:Temporary lintel height is measured from

finished floor protector level.

Ensure suitable air vents (min. 2 x 160mm diameter or equivalent) in place to vent firebox space -

these maybe located in the rear or in the side wall space;make allowance (min. 2 x 160mm

diameter or equivalent) at the top of the chimney chase, Pg.13.Ensure vents are bird and vermin

proofed.

CAVITY PREPARATION

Allow 5mm gap between plaster and flange to

ensure stainless steel cover can be fitted to the

box. DO NOT PLASTER OVER THE FLANGE.

Jet master

Flange

Inhaltsverzeichnis

Andere Jetmaster Kamin im Innenbereich Handbücher

Jetmaster

Jetmaster 1200 series Montageanleitung

Jetmaster

Jetmaster SLOW COMBUSTION Bedienungsanleitung

Jetmaster

Jetmaster kemlan supernova rf insert Handbuch

Jetmaster

Jetmaster UNIVERSAL 440 Bedienungsanleitung

Jetmaster

Jetmaster INSET STOVE MKIII 16i Betriebsanleitung

Jetmaster

Jetmaster MYNX Bedienungsanleitung

Jetmaster

Jetmaster Open Wood Fire Bedienungsanleitung

Jetmaster

Jetmaster Universal 500 Bedienungsanleitung

Jetmaster

Jetmaster HEAT & GLO MEZZO-AU Bedienungsanleitung

Jetmaster

Jetmaster 400 Handbuch

Jetmaster

Jetmaster UNIVERSAL Montageanleitung

Jetmaster

Jetmaster 700 Montageanleitung

Jetmaster

Jetmaster MK6 Betriebsanleitung

Jetmaster

Jetmaster UNIVERSAL 440 Montageanleitung

Jetmaster

Jetmaster Al Fresco Bedienungsanleitung

Jetmaster

Jetmaster 700 Double-sided Montageanleitung

Jetmaster

Jetmaster 700 Vent Free Built in Bedienungsanleitung

Jetmaster

Jetmaster Standard 16 Bedienungsanleitung

Jetmaster

Jetmaster Universal 500 Handbuch

Jetmaster

Jetmaster DROP IN 1020 Bedienungsanleitung

Jetmaster

Jetmaster GF1016 Bedienungsanleitung

Beliebte Kamin im Innenbereich Handbücher anderer Marken

Brigantia

Brigantia 35-DVRS31N-2 Betriebsanleitung

Nordpeis

Nordpeis Bergen Bedienungsanleitung

Superior

Superior BCT2536TMN Bedienungsanleitung

Quadra-Fire

Quadra-Fire 5100I-GD-B Bedienungsanleitung

Renaissance

Renaissance RUMFORD 1000 Bedienungsanleitung

Lacunza

Lacunza IV-800 Bedienungsanleitung

Baxi

Baxi 940 Gebrauchsanweisung

Dru

Dru Maestro 60/2 Tall RCH Bedienungsanleitung

Diamond Fireglass

Diamond Fireglass SS-O22 Bedienungsanleitung

HearthStone

HearthStone Windsor Bay 8830 Programmierhandbuch

Napoleon

Napoleon ASCENT B42 Bedienungsanleitung

Enviro

Enviro E33GI Bedienungsanleitung

Smeg

Smeg L30 FABE Montageanleitung

KEDDY

KEDDY K700 Bedienungsanleitung

Godin

Godin 3451 Bedienungsanleitung

Jøtul

Jøtul Jotul GI 535 DV IPI New Harbor Bedienungsanleitung

Austro Flamm

Austro Flamm Heidi Back 2.0 945048 Bedienungsanleitung

Desa

Desa CCFPDFT Bedienungsanleitung