Jetson DRIFTER Bedienungsanleitung
1
DRIFTER
ELECTRIC POWERED
360° RACER
-MANUAL-
2
3
TABLE OF CONTENTS
A. Introduction 4
B. In The Box 5
C. Features And Specs 6
D. Assembly 7
E. Charging the Battery 9
F. Operating the Drifter 10
G. Care and Maintenance 13
H. Safety Warnings 14
I. Warranty 16
J. Product Registration 17
4
Congratulations on your new Jetson Drifter Electric Powered 360°
Racer! The Drifter is an innovative and fun electric racer, ready to take
on everyday use. Before your rst ride, check whether the wheels are
damaged, or parts are loose. If there are any abnormalities, please
contact Jetson Customer Support at 1-(888) 976-9904 or email us at
customerservice@jetsonbike.com.
This product manual can help you understand, use, and maintain
your Drifter. In order to avoid danger caused by collisions, falls, and
loss of control, please use caution and learn how to ride the Drifter
safely. Jetson and authorized dealers cannot be held liable for injury or
damage caused from riding the Drifter. Users ride at their own risk.
The rider is responsible for consequences caused by violating warnings
or improper operations.
If you want to return this product for any reason, be sure to rst call or
email us before taking it back to the store so we can assist you.
INTRODUCTION
5
IN THE BOX
1. Front Wheel
2. Foot Rests
3. Base
4. Headlight
5. Handlebar
6. Stem
7. Seat
8. Fork
9. Back Wheels
10. Charging Cable
11. Charger
1
2
2
4
5
7
9
6
8
Included in the box:
• Drifter (some assembly required) • 1x Large Screw
• Manual • 2x Medium Screws
• Charger • 4x Small Screws
• Charging Cable • Allen Wrench
10
11
3
6
FEATURES AND SPECS
MODEL: DRIFTER
WHEEL SIZE: FRONT: 8”
REAR: 3”
MAX SPEED: 6 MPH
MAX RANGE: 8 MILES
BATTERY TYPE: LEAD ACID
BATTERY CAPACITY: 12V, 8AH
MOTOR TYPE: CHAIN
MOTOR: 120W
CHARGER: UL AC110-240V
CHARGE TIME: 2-3 HOURS
PRODUCT WEIGHT: 24.6 LBS
WEIGHT LIMIT: 154 LBS
RECOMMENDED AGE: 8+
WATER RESISTANT: NO
CLIMBING: 10°
1. Brake
2. Brake Lever Adjuster
3. Speed Mode Switch
4. Throttle Button
5. Stem Tube
1
3
4
2
5
7
Step One: Attach the Back Wheels to the bottom of the Fork and tighten
into place using the provided Allen Wrench. Then, insert the Stem into
the Fork and attach using the two Medium Screws. Make sure the bolts
and the screws are tight and secure.
ASSEMBLY
Attach
the Back
Wheels
Insert
Stem into
Fork and
tighten
the two
Medium
Screws
Place Bolt
into the
bottom of
the Fork
and
tighten.
8
Step Three: Align the holes in the Seat with the holes in the Frame and
attach using the four Small Screws.
Four Small
Screws
Step Two: Insert the Stem Tube into the back of the Base. Properly align
the holes in the Stem Tube with the holes in the back of the Base. Secure
the two pieces together using the Large Screw.
Attach the
Stem Tube
9
Your Drifter comes with a built-in rechargeable lead acid battery. Always
use the provided charger only. The Charging Port is located below the
Stem Tube of the Drifter. Please remember to cover the Charging Port
when you are done charging the Drifter. Before your rst ride you must
fully charge the Drifter - charge for 4 hours for the rst 3 times you use
it. For every ride after, charge your Drifter until it is fully charged, and
NOT LONGER. Do not leave any chargers plugged in overnight, or
leave it plugged in past the charge time.
CHARGING THE BATTERY
1. Plug one end of the power cord into a grounded AC outlet and the
other into the Drifter’s Charging Port. The red charging light on the
charger unit will turn on.
2. The red light will turn green once fully charged. Recharge the Drifter
after each use.
(Please note: Always plug the charger into the wall rst before the
device. If the wall outlet doesn’t have power and you plug the charger
into the device rst, it will light green, even if the battery is not full. So
always plug into the wall rst to make sure there is power.)
THE CHARGER OFFERS A CHARGING STATUS ON THE TOP OF THE
CHARGER:
CHARGING LIGHT RED: Battery is charging.
CHARGING LIGHT GREEN: Charging is complete.
Don’t use the Drifter if the battery emits strange odors, overheats,
or begins leaking. If the battery does leak, do not touch any leaking
materials, as the battery contains dangerous substances. Do not open
the battery and do not insert anything into the battery.
Only use the provided charger for the Drifter. Do not charge the battery
if it has over-discharged. It should be discarded for your safety. Do not
turn on the Drifter while it is charging.
Charging
Port
10
OPERATING THE DRIFTER
TURNING THE DRIFTER ON AND OFF
To turn the Drifter on, ip the Power Switch located on the left side of
the Drifter below the Stem Tube to “I” or on.
To turn the Drifter off, rst make sure the Drifter is not in motion. Then,
ip the Power Switch to “O” or off.
SAFE RIDING
Helmet: Most serious injuries that occur while riding are head injuries.
This could be prevented by wearing a helmet.
Elbow and Knee Pads: For added protection, always wear elbow and
knee pads when riding your Drifter, to prevent any serious injuries.
Get to know the Drifter before riding it. Test your control over it. Make
your turns slowly and cautiously, and give yourself stopping distance.
Always keep your feet on the Foot Rests and both hands holding onto
the Handlebar when you ride. It is recommended you practice your rst
ride on the Drifter in an open space with no obstacles in your way.
Turns - The turns on the Drifter are commanded by the direction you
turn the Handlebar/Front Wheel in. Before turning, look both ways to
make sure your path is clear.
Power
Switch
On
Inhaltsverzeichnis
