Jetson AMBER ALIT-3 Bedienungsanleitung

Lit

LED Strip Lights.

A guide for your lights.

IMPORTANT: READ CAREFULLY, RETAIN FOR FUTURE REFERENCE.

MODEL: ALIT3  ALIT6  ALIT9

Designed in Brooklyn | Made in China

Table of Contents

............................................................. 

........................................................... 

......................... 

........................................ 

Safety Warnings

Specs & Features

Preinstallation & Installing Your Lights

Operating the Motion Sensor

Safety Warnings

• Keep these instructions.

• Nonuser replaceable light sources.

• Uncoil the light strip before use.

• Do not drop, puncture, open, cut, or disassemble this product

• Do not install this product in any way other than what is outlined in

this guide.

• Do not place this device on hot surfaces.

• Only use the adaptor supplied; using a dierent adaptor can damage

the device.

• Do not submerge the strip or the power supply unit in water.

• Avoid long exposure to direct sunlight, which may cause damage

• Do not use this product in small, enclosed locations that could limit

the low of air or trap excess heat.

• Do not expose this product to open lames or use near ire.

• Do not use the product in a strong magnetic ield.

• Do not use this product for emergency lighting/exits.

• Do not allow small children to operate, modify, or install this

device unsupervised.

• Use a clean, soft cloth to clean - do not use any cleaning agents

to clean.

• Manage in accordance with disposal laws in your area.

• Do not clean the device when it is on and connected to the

power supply.

• Do not connect the light strip to the power supply while it is in the

packing or wound onto the reel.

• Do not use the rope light when covered or recessed into

a lat surface.

• Not intended for illumination. Only use for ambiance.

California Proposition 65

WARNING:

This product can expose you to a chemical such as Cadmium that is

known to the state of California to cause cancer or birth defects or

other reproductive harm. For more information go to

www.p65warnings.ca.gov/product

NOTICE OF COMPLIANCE

Changes or modiications not expressly approved by Jetson could

void the user’s authority to operate the equipment.

This device complies with Part 15 of the FCC Rules. Operation is

subject to the following two conditions:

(1) this device may not cause harmful interference, and

(2) this device must accept any interference received, including

interference that may cause undesired operation.

NOTE: This equipment has been tested and found to comply with the

limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.

These limits are designed to provide reasonable protection against

harmful interference in a residential installation. This equipment

generates, uses, and can radiate radio frequency energy, and if not

installed and used in accordance with the instructions, may cause

harmful interference to radio communications. However, there is no

guarantee that interference will not occur in a particular installation. If

this equipment does cause harmful interference to radio or television

reception, which can be determined by turning the equipment o

and on, the user is encouraged to try to correct the interference by

one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit dierent from

that to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician

for help.

This equipment complies with FCC radiation exposure limits set forth

for an uncontrolled environment. This equipment should be installed

and operated with minimum distance 20 cm between the radiator &

your body.

LIMITED 1 YEAR WARRANTY

Limited 1 Year Warranty only applies to the manufacturer defects.

Contact Jetson Customer Care for detailed information via support.

ridejetson.com

Limited 1 Year Warranty does NOT cover:

• Normal wear and tear

• Improper assembly

• Corrosion

• Improper maintenance

• Installation of components, parts, or accessories not originally

intended for or compatible with the product as sold

• Damage or failure due to accident, misuse, abuse, or neglect

• Labor charges for part replacement or changeover

• Non-proprietary products (any other original part or component)

covered by the original manufacturer’s warranty

• Any accessories

Specs & Features

• WATTS: 1.5W

• BATTERY: RECHARGEABLE 1000MA3.7V

• CHARGER: DC5V MICRO USB

• CHARGING TIME: UP TO 3 HOURS

• SENSOR DISTANCE: UP TO 16.5FT

• OPERATING TEMPERATURE: BETWEEN 4F AND 113F

• LED STRIP WATER RESISTANCE RATING: IP44 SPLASH PROOF

• MOTION SENSOR CONTROLLER WATER RESISTANCE

RATING: IP20 NOT WATER RESISTANT

What’s in the Box

1. LED STRIP LIGHTS

2. MOTION SENSOR CONTROLLER

3. USB CHARGING CORD

4. MOUNTING ADHESIVE

MOTION SENSOR CONTROLLER

1. Get Started

1.1 Preinstallation

1.2 Installing Your Lights

• CHECK THAT YOU HAVE EVERYTHING. BOX SHOULD

CONTAIN AMBER LIT STRIP, MOTION SENSOR CONTROLLER,

USB CHARGING CORD AND MOUNTING ADHESIVE.

• MAKE SURE THE MOTION SENSOR IS CHARGED USING THE

USB INCLUDED.

• AFTER IT IS CHARGED, PLUG THE END OF THE LIGHT STRIP

INTO THE MOTION SENSOR PORT.

• WIPE DOWN AND CLEAN THE SURFACE YOU’RE PLANNING

TO PLACE YOUR LIGHTS ON.

• THE CIRCULAR MAGNET INCLUDED WILL ATTACH TO THE

BACK OF THE MOTION SENSOR CONTROLLER. SECURE THE

3M ADHESIVE INCLUDED TO THE EXPOSED SIDE OF THE

MAGNET TO MOUNT TO THE WALL.

• PEEL OFF THE PROTECTIVE TAPE ON THE BACK OF THE

LIGHTS AND MAGNETIC MOTION SENSOR MOUNT.

• PLACE LIGHTS ONTO SURFACE AND MOTION SENSOR ONTO

MAGNET. PRESS DOWN TO MAKE SURE ADHESIVE IS FIRMLY

SECURED TO SURFACE.

1.3 Operating the Motion Sensor

4 67 5

1. ‘RGB‘ KEY:

• ENABLES ‘STATIC’ MODE, TOGGLE BETWEEN 21 DIFFERENT

COLOR OPTIONS

2. ‘MODE’ KEY:

• ENABLES ‘DYNAMIC’ MODE, CYCLES BETWEEN 8 DIFFERENT

LIGHT FUNCTIONS

3. ‘+/-‘ KEY:

• WHEN LIGHTS ARE STATIC, THIS CYCLES THROUGH

5 LEVELS OF BRIGHTNESS

• WHEN LIGHTS ARE IN DYNAMIC MODE, THIS CYCLES

THROUGH 5 LEVELS OF SPEED

• PRESS AND HOLD FOR 1 SECOND TO TURN OFF

4. TIMER SWITCH:

• ADJUST THE LENGTH OF TIME LIGHTS WILL POWER OFF

AFTER NO MOTION IS DETECTED

5. OFF:

• MOVEMENT AND LIGHT SENSORS ARE OFF

6. SUN SWITCH:

• MOTION SENSOR ENABLED  LIGHT WILL TURN ON WHEN IT

DETECTS MOVEMENT

7. MOON SWITCH:

• MOTION AND LIGHT SENSOR ENABLED: SENSOR WILL ONLY

TURN ON WHEN IT DETECTS BOTH MOVEMENT AND LIGHT UP

TO 25 LUX

*WARNING WHEN BRIGHTNESS OF LIGHT BEGINS TO

DULL IT INDICATES THE BATTERY POWER IS INSUFFICIENT,

PLEASE CHARGE THE CONTROLLER IMMEDIATELY

CIRCULAR BULB DETECTS MOTION AND LIGHT

LIGHT STRIP

PORT

MICRO USB

CHARGING PORT

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Jetson Beleuchtungsausrüstung Handbücher

Jetson

Jetson AMBER Volt TBH Bedienungsanleitung

Beliebte Beleuchtungsausrüstung Handbücher anderer Marken

Brizo

Brizo 8SP-MU-4 Bedienungsanleitung

LUCE&LIGHT

LUCE&LIGHT BROM 1.0 Bedienungsanleitung

IKEA

IKEA BJÖRKSPIREA Bedienungsanleitung

Laserworld

Laserworld Evolution Series ES-400RGB Bedienungsanleitung

Alien

Alien RG STAR Bedienungsanleitung

EuroLite

EuroLite LED B-40 Bedienungsanleitung

Qazqa

Qazqa Suplux SL 3 Black 103062 Bedienungsanleitung

Commercial Electric

Commercial Electric 54568141 Bedienungsanleitung

CREE LIGHTING

CREE LIGHTING 304 Series Bedienungsanleitung

Goobay

Goobay 49867 Bedienungsanleitung

ECOMAN ITALIA

ECOMAN ITALIA LED T8 Bedienungsanleitung

Alkalite

Alkalite Krypton KT-81 Bedienungsanleitung

Clas Ohlson

Clas Ohlson GU10 Bedienungsanleitung

DTS

DTS DELTA 10 F Bedienungsanleitung

ring

ring Solar Steplight Bedienungsanleitung

One Stop Gardens

One Stop Gardens 57696 Montageanleitung

Chauvet DJ

Chauvet DJ COREpar UV120 ILS Bedienungsanleitung

SIREM

SIREM Swimeo A2 Bedienungsanleitung