JGaurora A5 Bedienungsanleitung
USER GUIDE
1. Preface...................................................................................................................................................................................... 2
1.1 Introduction..............................................................................................................................................................2
1.2 Safety advice............................................................................................................................................................ 2
1.3 Filament requirements.............................................................................................................................................2
1.4 Environmental requirements................................................................................................................................... 2
2. About A5................................................................................................................................................................................... 3
2.1 Basic reference......................................................................................................................................................... 3
2.2 Overview of A5......................................................................................................................................................... 3
2.3 Extruder Nozzle Assembly (Exploded View Diagram)............................................................................................ 4
2.4 Tool box lists.............................................................................................................................................................5
2.5 Input Power adjustment................................................................................................................................................... 5
3. About JGcreat software........................................................................................................................................................... 6
3.1 Software installation................................................................................................................................................ 6
3.2 JGcreat introduction.................................................................................................................................................7
4. Basic printing.......................................................................................................................................................................... 11
4.1 Control menu introduction.................................................................................................................................... 11
4.2 Main menu introduction........................................................................................................................................ 12
4.3 Platform leveling.................................................................................................................................................... 12
4.4 Filament loading.....................................................................................................................................................13
4.5 Trial printing........................................................................................................................................................... 15
4.6 Filament replacement notes.................................................................................................................................
16
5. Common problems and solutions......................................................................................................................................... 17
6. 3D printer maintenance.........................................................................................................................................................18
6.1 Daily maintenance..................................................................................................................................................18
6.2 Basic maintenance................................................................................................................................................. 18
6.3 Maintenance of moving components.................................................................................................................... 18
7. Support and service details................................................................................................................................................... 19
1
Contents
I.1 Introduction
The JGAURORA A5 User Guide was written to help new A5 users to start their printing journey with the
JGAURORA A5. Even if you are familiar with earlier JGAURORA machines or experienced with 3D printing technology,
we still recommend that you read through this guide, as there is lots of important information about the A5, that will
help you have a better 3D printing experience.
1.2 Safety Advice
1) During printing, the temperature of the printing nozzle tip can heat up to 250℃. To avoid being burned, be
careful to avoid touching the nozzle while it is hot. The heated bed can also heat up to 100C, so please allow the bed
to cool down after printing, before you try to remove your completed prints.
2) While the printer is operating, there is a danger of hands or fingers being crushed by moving parts. To prevent
injury, please keep hands and long hair safely away from moving components, while the printer is operating.
3) Always use the A5 with a properly grounded outlet. Do not modify the A5 power plug.
Attention: Before power on, please check the input power is compatible with your local standard.( Method:
Observe the power switch at the hole of back base, if your local voltage is 230V, then adjust it to 230V, Similarly,
if the voltage is 115V, then adjust it to 115V. This process is described in detail in Chapter 2.)
4) When the A5 continuously work over 96 hours, it should be stop for 1-3 hours to restart.
5) Please be careful when removing prints. The print bed is a glass sheet, so to avoid damage, please avoid using
excessive force. We recommend wearing protective glasses while removing prints. If you are using a spatula or
scraper to remove prints, please wear gloves to protect your hands from serious injury, and be careful not to damage
the print bed surface.
1.3 Filament requirements
Do not abuse the filament. Please make sure you use the JGAURORA filament or the filament from the brands
certified by JGAURORA. All polymers degrade with time. Do not unpack until filament is needed. Filament should be
stored at room temperature:15-30ºC, and in dry conditions.
PLA filament in particular can absorb moisture from the air, to become brittle and unsuitable for printing. If you
are not printing for extended periods of time, it is recommended to remove the filament and store it in an air-tight
box. Use the filament holes in the spool to hold the loose end of the filament, to prevent it coming loose and
becoming tangled.
1.4 Environmental requirements
The ambient temperature in the printing enviroment should be between 5 to 4ºC, with humidity between 20%
1. Preface
2
to 50%. Using the printer outside of these conditions may result in reduced or inconsistent printing quality.
2.1 Basic reference
Model number: A5 Device size: 536*480*543mm
Layer thickness: 0.1 to 0.3mm Device weight: 13.8kg
Printing speed: 10 to 150mm/s (suggest 30 to 60mm/s) Package size: 640*610*280mm
Nozzle temperature: Room temperature to 250ºC Package weight: 17kg
Nozzle diameter: 0.4mm Build size: 305*305*320 mm
Hot bed temperature: Room temperature to 110ºC Platform material: Black Diamond Glass heated plate
Support material: PLA /ABS/WOOD+PLA/PETG LCD display: 2.8” Touch Screen
Filament diameter: 1.75mm Connectivity: USB cable/ USB stick
Language: English/German/French/Spanish/Japanese Support Formats: STL/OBJ/G-Code
Environmental requirements:
Temperature 5 to 40ºC, Humidity 20% to 50%
OS: Windows, Linux, Mac
AC Input: AC115 OR 230V, manually switchable Software: Cura/Simplify 3d/JGcreat(Win 7 64 bit)
2.2 Views of A5
2. About A5
3
Item No. Parts Name
1
1
Extruder cover
2
2
PTFE Tube Quick-coupler
3
3
Square Extruder Cooling fan
4
4
Blower Part Cooling Fan
5
5
Limit switch
6
6
Linear bearing
7
7
Threaded Extruder Throat
Item No. Parts Name
8
8
Cooling Duct
9
9
Extruder Nozzle
10
10
11
11
12
12
13
13
Heater block
Bearing seat II
Bearing seat I
Wiring harness block
2.3 Extruder Nozzle Assembly (Exploded View Diagram)
4
5
2.4 Tool box lists
2.5 Input Power Voltage adjustment
The Input Power of A5 is selectable, AC 115/230, please adjust it according to your local voltage standard as below:
Observe the voltage
data in the hole of
back base.
If the voltage shows
230V, then the input
power is 230V.
Move the toggle
switch to left side,
then shows 115V.
Move the toggle
switch to right side,
then shows 230V.
3.1 Software installation
Copy the files in USB stick to your PC, then double click the software installation icon. Then, follow the
installation instructions, as shown in the photos below.
Double click
3. About JGcreat software
6
7
After clicking the “Finish” icon, the software is installed, and ready for use.
3.2 JGcreat introduction
1) Open the software(JGcreat)
Double click to
Open “JGcreat”
2) Choose the language you prefer (English as an example):
8
4) Load 3d file and slice it
Load an stl or obj 3d file. Select the appropriate print quality. The lower right corner of the software shows "Slicing",
which converts the 3D model file, into the standard GCode instructions that the printer uses to run.
Choose the
print quality
you prefer
Choose A-5
9
Inhaltsverzeichnis
Andere JGaurora 3D-Drucker Handbücher
JGaurora
JGaurora A8S Bedienungsanleitung
JGaurora
JGaurora A7 Bedienungsanleitung
JGaurora
JGaurora A3S Bedienungsanleitung
JGaurora
JGaurora A3S Bedienungsanleitung
JGaurora
JGaurora JGMAKER Magic Bedienungsanleitung
JGaurora
JGaurora Z-603S Technisches Handbuch
JGaurora
JGaurora A-4 Bedienungsanleitung
JGaurora
JGaurora A-8 Bedienungsanleitung
JGaurora
JGaurora A7 Bedienungsanleitung
