JL Audio Stealthbox SB-F-SUPRCNSL/10W3v3 Bedienungsanleitung

➔

Stealthbox®

INSTALLATION GUIDE

SB-F-SUPRCNSL/10W3V2, JL AUDIO, Inc 2005 Sheet SKU#011149 Revision 8/4/2005Page 1

for the

SB-F-SUPRCNSL/10W3v2

(‘98-Up Ford SuperDuty

250,350,450,550 & 650

‘00-Up Excursion)

This Stealthbox is a product which

requires professional installation skills and

tools.

Please read this installation guide thor-

oughly before beginning the project. It

will guide you step by step through the

installation.Several of the steps in this

process may require two people to

accomplish.

It is absolutely vital that the enclosure

be properly mounted to the vehicle

according to these instructions. Failure

to mount the enclosure properly pres-

ents two problems: 1)The sub-bass

performance will suffer due to the

movement of the enclosure caused by

the force exerted by the woofer(s) and

2) A loose enclosure presents a serious

safety hazard in the event of a collision

or sudden deceleration.

Please enjoy your JLAudio Stealthbox

responsibly.

STEP 1:

From inside the factory console,

using a 9/16”socket,remove the four bolts

that secure the console to the vehicle. (Two

of these bolts will be used later to secure

the Stealthbox).

STEP 2:

Remove the console from the vehi-

cle.

STEP 3:

Remove the inside section of the

console.(This will not be reinstalled).

-Two screws are located under the front tray.

-Three screws attach the hinge.

-Three screws are located on each side of the

consoles shell (six total)

After this section is removed, the console shell

will be in two parts.

STEP 4:

Using a pair of pliers,from the inside

of the console shell.Remove the ridges locat-

ed toward the front of the console.

STEP 5:

Reassemble the front and rear parts

of the console shell using the supplied hard-

ware (4 #8 x 1/2”long screws,4 washer and

4 nuts) as shown in the picture.

STEP 6:

Turn the console shell upside down.

Position the Stealthbox inside the shell,

START

HERE

Continued on Next Page ➔

www.jlaudio.com

➔

STEP 7: Use the remaining mounting holes as a

drill guide.

Using a 1/8” drill bit and drill, drill a hole through

each of these guide holes, into the Stealthbox.

STEP 8: Install #8x 1/2” black pan-head screws

into the drilled holes.

➔➔

➔➔➔

STEP 10: Install #8 x 1/2” black pan-head screws

into the drilled holes.

Cont..

From

Page

Continued on Next Page ➔

➔

STEP 11: Using a 1/8” drill bit and drill. Drill two

holes at the hinge area using the outside holes only.

The center hole does not need to be drilled.

➔

STEP 12: Remove the screws installed in STEP 8

and STEP 10. Separate the console shell from the

Stealthbox.

STEP 13: Attach the OEM’s console lid to the

shell. Use one of the OEM’s screws and supplied

speed-clip to the center hole of the hinge.

STEP 9: Turn the console right-side-up with the

Stealthbox attached.

Using the holes on the top of the console shell as

guides, use a 1/8” drill bit and drill to drill holes

through each of these guide holes and into the

Stealthbox.

SB-F-SUPRCNSL/10W3V2, JL AUDIO, Inc 2005 Sheet SKU#011149 Revision 8/4/2005Page 2

www.jlaudio.com

STEP 14: Place the Stealthbox in the vehicle. Using

a pair of OEM bolts, from STEP 1. Loosely secure

the rear foot bracket to the floor, do not tighten.

STEP 15: Remove the paper backing on the sup-

plied sheet wax squares.

With the Stealthbox in place, lift the front of the

Stealthbox and position both supplied sheet wax

squares onto the carpet and lined up with the front

foot bracket of the Stealthbox, lower the console

down.

STEP 16: Using one of the supplied 3/8”x1-1/2”

bolts, place the bolt through each hole of the front

foot bracket (one at a time). Press down on the bolt,

too leave impressions on the sheet wax squares.

STEP 17: Remove the two OEM bolts from STEP

14. Remove the Stealthbox from the vehicle.

➔➔

➔➔ ➔

VEHICLE SHEET METAL

METAL BRACE PLATE

FLAT WASHER

HEX NUT

FRONT MOUNTING BRACKET

OF BRACKET

LOCK WASHER

FLAT WASHER

BOLT

STEP 19: Run speaker wire to the Stealthbox’s

location. Make sure the speaker wire is going to be

accessible at the rear of the Stealthbox.

*At this time, double check for proper oper-

ation of woofer*.

Cont..

From

Page

Continued on Next Page ➔

➔

STEP 18: With a 1/8” drill bit and drill, drill a pilot

hole.

With a 1/2” drill bit and drill, drill a hole through each

of the two locations.

*Caution: Check under the vehicle for any

loose brake lines, fuel lines, transfer case or

other hazards before drilling.Always wear

eye protection when drilling.*

➔

STEP 22: A second person is needed to help out in this

step.

Place a supplied flat washer onto each supplied 3/8”x1-1/2”

bolt. Place each bolt assembly through the front bracket of

the Stealthbox and the drilled holes from STEP 18.

From under the vehicle, place the supplied metal brace plate,

flat washer, lock washer and nut onto each bolt assembly.

With a second person inside the vehicle securing the bolt

head with an open-end wrench.Tighten the nut onto the

bolt assembly.

STEP 21: Replace the OEM bolts back to

the rear foot bracket. Hand-tighten the rear

bolts.

SB-F-SUPRCNSL/10W3V2, JL AUDIO, Inc 2005 Sheet SKU#011149 Revision 8/4/2005Page 3

www.jlaudio.com

STEP 25: Tighten the bolts at the rear of the

Stealthbox,inside the vehicle.

STEP 26: Connect the speaker wire to

the terminal cup on the Stealthbox. STEP 27: Place the pair of supplied alu-

minum spacers over the two holes that are

located at the upper rear of the Stealthbox,

From STEP 11.

STEP 20: Position the Stealthbox back into place.

Specifications:

Enclosure Type: Sealed

Driver Type: 10W3v2-D6

Nominal Impedance: 3Ω

Cont.. Power Handling: 300Watts

JLAudio recommends using a high quality amplifier such as the JLAudio 250/1. The diagram below shows the recommended

crossover, infrasonic filter and equalizer settings for the 250/1 when being used to power your Stealthbox®.

Included Hardware:

2) 3/8” x 1-1/2” bolts

2) Sheet wax squares

4) flat washer

4) #8-32 Kep nuts

2) Felt pads

2) 3/8” Lock washer

2) 1/2” Aluminum spacers

4) #8-32 x 1/2” Machine screws

4) #8 x 1/2” Sheet metal screws

4)#8 x 1-1/4” Sheet metal screw

1) Metal Brace Plate

10369 N. Commerce Pkwy, Miramar, Florida 33025-392 Phone: 954.443.1100 Fax: 954.443.1111

JL AUDIO 250/1

monoblock subwoofer amplifier

Amplifier Input Section

Input Sens.

Input Voltage

Low/High

Left Ch. Right Ch.

Signal Sensing

Off/On

Output Mode

Full-Range/Low-Pass/High-Pass

Left Ch. Right Ch.

Amp LP Filter

Mode/Slope

Off/12dB/24dB

Filter Freq. (Hz)

Bass Control

LF Boost (dB)

Off/30Hz

Infrasonic Filter

+1 +13

+10

Preamp Output Section

+12VDC Ground Remote

The JLAudio 250/1 is a very versatile audio component. Please consult the owner’s manual for detailed information

about installing and tuning this amplifier.

➔➔➔

STEP 28: Position the OEM console shell over the

Stealthbox.

*Make sure that the aluminum spacers from

STEP 27, do not move from their location.*

STEP 32: Place the supplied pair of felt pads

between the lid and the console shell.This is going

to prevent vibration contact of console storage lid

and console shell.

➔

SB-F-SUPRCNSL/10W3V2, JL AUDIO, Inc 2005 Sheet SKU#011149 Revision 8/4/2005Page 4

www.jlaudio.com

Mid/High Frequency Driver Information:

CONGRATULATIONS!

INSTALL COMPLETE.

XR570-Csi

TR570-Cxi

Front Location Driver Size:

5”x7”

Applicable JL Audio Products:

TR,VR, XR ZR570-Csi

Rear Location Driver Size:

5”x7”

Applicable JL Audio Products:

TR, XR570-Cxi

Cont..

From

Page

STEP 29: Insert the pair of supplied #8 screws

through the hinge holes (STEP 11) and into the

Stealthbox.

STEP 30: Reinstall the remaining supplied screws

that attach the console shell to the Stealthbox.

These screws were removed in STEP 12.

STEP 31: Replace the front tray.

Difficulty Scale

Dieses Handbuch passt für folgende Modelle

Andere JL Audio Autolautsprecher Handbücher

JL Audio

JL Audio C2-650x Bedienungsanleitung

JL Audio

JL Audio C2-570x Bedienungsanleitung

JL Audio

JL Audio TR600-CXi Bedienungsanleitung

JL Audio

JL Audio XR525-CXi Bedienungsanleitung

JL Audio

JL Audio XR570-CXi Bedienungsanleitung

JL Audio

JL Audio Stealthbox SB-GM-AVAL/12W3v3 Bedienungsanleitung

JL Audio

JL Audio ZR570-CSi Bedienungsanleitung

JL Audio

JL Audio C2-600x Bedienungsanleitung

JL Audio

JL Audio stealthbox SB-J-WRUD/10TW1 Bedienungsanleitung

JL Audio

JL Audio SB-F-SUPRCNSL/10W3v2 Bedienungsanleitung

JL Audio

JL Audio XR653-CS Bedienungsanleitung

JL Audio

JL Audio C3-100ct Bedienungsanleitung

JL Audio

JL Audio VR650-CSi Bedienungsanleitung

JL Audio

JL Audio ZR525-CSi Bedienungsanleitung

JL Audio

JL Audio Evolution C5-650 Bedienungsanleitung

JL Audio

JL Audio VR600-CSi Bedienungsanleitung

JL Audio

JL Audio C2-525x Bedienungsanleitung

JL Audio

JL Audio TR650-CSi Bedienungsanleitung

JL Audio

JL Audio MX650-CCX Bedienungsanleitung

JL Audio

JL Audio C2-650x Bedienungsanleitung

JL Audio

JL Audio SB-F-Edg Bedienungsanleitung

JL Audio

JL Audio XR570-CSi Bedienungsanleitung

JL Audio

JL Audio M770-CCS Bedienungsanleitung

JL Audio

JL Audio Stealthbox 94376 Bedienungsanleitung

Beliebte Autolautsprecher Handbücher anderer Marken

Blaupunkt

Blaupunkt GTt 300 Technisches Datenblatt

Boston Acoustics

Boston Acoustics SX55 Bedienungsanleitung

Kenwood

Kenwood KFC-W212 Bedienungsanleitung

VR3

VR3 Elite VRS653 Bedienungsanleitung

Premier

Premier TS-W3001D4 Bedienungsanleitung

Infinity

Infinity 6530cx Bedienungsanleitung

Focal

Focal K2 Power 165 KRX3 Bedienungsanleitung

Precision Power

Precision Power PPI4.2 Bedienungsanleitung

Jensen

Jensen XS Series Bedienungsanleitung

Blaupunkt

Blaupunkt GTx Series Bedienungsanleitung

AudioBahn

AudioBahn AT60 Bedienungsanleitung

Focal

Focal BombA 27 V1 Bedienungsanleitung

Blueant

Blueant S1 Bedienungsanleitung

Naxa

Naxa NCS-768 Bedienungsanleitung

Focal

Focal Polyglass 130 VRS Bedienungsanleitung

Boston Mobile Audio

Boston Mobile Audio SR80 Bedienungsanleitung

Blaupunkt

Blaupunkt GTx 352 DE Bedienungsanleitung

Focal

Focal K2 POWER 130 KF Bedienungsanleitung