JL Audio M770-CCS Bedienungsanleitung

Thank you for choosing a JL Audio Marine Component System.

With proper installation, your new speakers will deliver

years of listening pleasure.

We strongly recommend that you have your new marine speakers

installed by your authorized JL Audio dealer.

The installation professionals employed by your dealer have

the necessary tools and experience to properly install your new speakers.

If you prefer to perform your own installation,

please read this instruction manual completely before

beginning the process.

OWNER’S MANUAL

7.70-inch (196 mm) Cockpit & Tower Component Systems

M770-CCS / M770-TCS

2 JL AUDIO M770-CCS / M770-TCS

Woofer Physical Specifications

Woofer Frame Outer Diameter (A) 7.70 in. / 196 mm

Bolt Hole Circle (B) 6.92 in. / 176 mm

Motor Overmold Outer Diameter (C) 4.41 in. / 112 mm

Woofer Frontal Grille Protrusion* (D) 0.99 in. / 25 mm

Woofer Mounting Hole Diameter (E) 6.25 in. / 159 mm

Woofer Mounting Depth (F) 3.15 in. / 80 mm

Notes: *Frontal grille protrusion measured from mounting surface

Tweeter Physical Specifications

Flush Mount Fixture Diameter (A) 2.38 in. / 60 mm

Flush Mount Mounting Hole Diameter (B) 1.875 in. / 48 mm

Flush Mount Mounting Cup Depth (C) 0.70 in. / 18 mm

Surface Mount Fixture Diameter (D) 2.44 in. / 62 mm

Surface Mount Protrusion (E) 1.02 in. / 26 mm

All specifications are subject to change without notice.

JL AUDIO M770-CCS / M770-TCS 3

CCS AND TCS MODELS...

WHAT IS THE DIFFERENCE?

CCS models have woofers specifically designed

for infinite-baffle applications. In plain english, this

means that they are designed to operate without

an enclosure behind them. The bass response of

the speaker will suffer significantly if placed in a

small enclosure.

TCS models are specifically engineered

for enclosed operation. This makes them

ideal for wakeboard tower systems or

other small enclosure applications.

M770CCS / M770TCS SPECIFICATIONS

Woofers: Injection-molded, mica-filled

polypropylene cone bodies with UV inhibitors,

1.25-inch (32 mm) voice coils, low-profile/

progressive-roll spiders and synthetic rubber

surrounds. DMA-optimized, long excursion

design for enhanced output and bass response.

UV-resistant polymer baskets

Tweeters: 1-inch (25 mm) treated silk dome

tweeter, neodymium magnet, ferrofluid cooled

and damped. Flush or surface mount capability.

UV-resistant polymer housings

Crossover Networks: True 2-way networks with

1st order low-pass and 2nd order high-pass circuits.

Polyswitch solid-state tweeter protection

Continuous Power Handling: 100 Watts (RMS Method)

Peak Music Power: 300 Watts

Recommended Power Range: 40-175 Watts (RMS)

Frequency Response: 45 Hz - 25 KHz (± 3 dB)

Efficiency @ 1W/1m: 91.0 dB

Nominal Impedance: 4 ohms

Included Components and Parts:

r5XPJODINNXPPGFST

r5XP1PMZNFS8PPGFS(SJMMFT

r5XPJODINN5XFFUFST

r5XP8BZ$SPTTPWFS/FUXPSLT

(mounted to woofers)

r5XP'MVTI.PVOU5XFFUFS'JYUVSFT

r5XP4VSGBDF.PVOU5XFFUFS'JYUVSFT

r5XFMWFYJODINNQBOIFBE

stainless-steel screws

r5XFMWFTUBJOMFTTTUFFMXBTIFST

r4JYYJODINNQIJMMJQTIFBE

stainless-steel screws

r5XPYJODINNQIJMMJQTIFBE

stainless-steel machine screws

r5XPTQSJOHTUBJOMFTTTUFFMDMJQT

r5XPSFEKVNQFSXJSFTQSFUFSNJOBUFE

r5XPCMBDLKVNQFSXJSFTQSFUFSNJOBUFE

r-PHP#BEHFT4QPSU(SJMMF.PEFMT0OMZ

 0OF1BJS#MBDL8IJUF5JUBOJVN#MBDL.PEFMT

 0OF1BJS3FE8IJUF5JUBOJVN#MBDL.PEFMT

 0OF1BJS8IJUF8IJUF.PEFMT0OMZ

 0OF1BJS5JUBOJVN5JUBOJVN#MBDL.PEFMT0OMZ

4 JL AUDIO M770-CCS / M770-TCS

BEFORE YOU BEGIN INSTALLING

r5VSOPGGUIFBVEJPTZTUFN*UJTBMTPBEWJTBCMF

to disconnect your battery system whenever

performing installation work.

r#FGPSFDVUUJOHESJMMJOHPSJOTFSUJOHBOZTDSFX

check clearances on both sides of the planned

mounting surface. Also check for any potential

obstacles, such as wiring harnesses, fuel lines,

hydraulic lines, etc. Check both sides of the vessel

before cutting any holes.

r8FBSQSPUFDUJWFFZFXFBSBUBMMUJNFTBOEBEVTU

mask and gloves when drilling or cutting.

It is absolutely vital that your component

system is connected as shown in this manual.

Failure to connect the system as shown will

result in damage to your speakers which is

NOT covered under warranty. Do not substitute

different crossover networks!

TWEETER PROTECTION

The crossover networks are equipped with

an advanced electronic tweeter protection

circuit designed to minimize the possibility

of tweeter failure. This electronic device

monitors current going to the tweeter and

will disconnect the tweeter from the signal

when it senses overload. Should this occur

while listening to the audio system, simply

reduce the volume for a few seconds and the

protection circuit will reset itself automatically.

SPEAKER PLACEMENT CONSIDERATIONS

A component system gives you the ability to

place the woofer and tweeter separately in your

vessel. As a general rule, the tweeters should be

placed relatively close to the woofers for best tonal

balance and most coherent imaging (the closer, the

better). Any separation greater than 8 inches (20

cm) is likely to result in degraded sound quality.

Avoid placing tweeters where they will be

blocked by objects (including seated occupants).

When selecting a mounting location, look at both

sides of the vessel to make sure that this location is

clear on both sides.

3:00 Position

9:00 Position

INTERCHANGEABLE LOGO BADGE

(Sport-Grille Models Only)

*OUFSDIBOHFBCMF-PHP#BEHFTGPS4QPSU(SJMMF

model component woofers are included to further

customize your installation. The design of the Sport

(SJMMFBMMPXTGPSUIF+-"VEJPMPHPUPCFBEEFEJO

your choice of included colors and oriented in the

manner that best suits your installation.

NOTE: A left and a right badge of each

color is included. These two different

PSJFOUBUJPOTFOTVSFUIFi+-"VEJPu-PHPXJMM

read correctly wherever positioned (most

commonly the 3:00 or 9:00 position).

Remove the adhesive backing from the badge

and affix the badge to the grille using the small

positioning hole as a guide. See diagram below.

JL AUDIO M770-CCS / M770-TCS 5

!! CAUTION !!

While these speakers are designed to be water and spray resistant, they are not designed to be submerged

or to withstand high-pressure water spray. Please exercise care when washing your boat to avoid damaging

your speakers. Do not install on submersibles, personal watercraft or any other vessel likely to be under

water at any time.

Prolonged exposure to sound pressure levels in excess of 100dB can cause permanent hearing loss. This

high-performance speaker can exceed this level. Please exercise restraint in its operation in order to preserve

your ability to enjoy its fidelity.

When installing speakers in your vessel, it is extremely important to secure them firmly. This applies not only

to the speakers themselves, but also any structure they are mounted to. If not firmly attached, the speakers

can become dangerous projectiles in a collision. Please review the mounting information carefully and use

the supplied marine-grade hardware to mount this product.

woofer

negative

input

tweeter

negative

input

from

amplier

negative

output

from

amplier

positive

output

tweeter

positive

input

woofer

positive

input

WIRING DIAGRAM

to amplier output

6 JL AUDIO M770-CCS / M770-TCS

TWEETER INSTALLATION PROCEDURE

(SURFACE-MOUNT)

1) Choose a flat mounting surface.

2) Drill a 1/4-inch (6 mm) diameter hole at the

center of your desired mounting location (to

pass the tweeter wires). To prevent cracking,

start with a smaller drill bit and gradually work

up the target diameter.

3) Place the surface mount cup at the desired

location and orientation. Then mark the

three mounting screw locations with a sharp,

pointed tool.

4) Remove the mounting cup and drill three

3/32-inch (2.38 mm) diameter pilot holes at the

locations you just marked. It is also advisable

to use a hand-driven countersink tool on each

hole to further inhibit gel-coat cracking of

fiberglass panels. Depending on the thickness

of the mounting surface, it may be necessary to

enlarge the screw holes slightly.

5) Place the mounting cup and align it over the holes

you just drilled. Then insert three of the supplied

YJODIQIJMJQTIFBENPVOUJOHTDSFXTBOE

tighten gradually with a hand screwdriver until the

cup is tight against the surface.

6) Insert the tweeter wires through the center

hole and then snap the tweeter into place by

pushing in firmly.

7) Connect the tweeter wires to the tweeter

output terminals on the crossover. See Wiring

Diagram on page 4.

INSTALLING THE SPEAKERS

0ODFUIFNPVOUJOHMPDBUJPOTIBWFCFFO

established, run speaker cables from the amplifier

outputs to the mounting locations. If you are

running cables through bulkheads, drill holes for

the cable and use a urethane or plastic grommet to

protect the wire from chafing in the hole. Make sure

that the cables will clear any mechanical devices

in the boat and secure them with wire ties. If you

are unsure about any part of this process, please

DPOUBDUZPVS+-"6%*0EFBMFSGPSJOTUBMMBUJPOIFMQ

TWEETER INSTALLATION PROCEDURE

(FLUSH-MOUNT)

1) Choose a flat mounting surface that has

sufficient depth to accept the mounting cup.

2) Cut a 1.875-inch (48 mm) diameter hole.

3) Preassemble the spring clip and mounting cup

as shown in Diagram A, using the supplied

machine screw

$MBTTJD(SJMMF.PEFMTIPXO

*OTUBMMBUJPOJTUIFTBNFGPS4QPSU(SJMMF

Models)

. Do not tighten fully.

4) Insert the cup into the mounting hole so that

the spring clip expands on the inside of the

mounting surface.

5) While holding the tweeter cup in the desired

orientation, tighten the machine screw (with a

hand screwdriver) until the cup is tight in the hole.

6) Insert the tweeter wires through one of the

slots in the cup and then snap the tweeter into

place by pushing in firmly.

7) Connect the tweeter wires to the tweeter

output terminals on the crossover. See Wiring

Diagram on page 5. Diagram B

Diagram A

JL AUDIO M770-CCS / M770-TCS 7

5) Remove the woofer and drill a pilot hole (see

chart below) in each of the screw locations. It is

also advisable to use a hand-driven countersink

tool on each hole to further inhibit gel-coat

cracking of fiberglass panels.

6) Connect the speaker wires from the amplifier,

the output wires to the tweeter and the jumper

wires to the woofer connections. See Wiring

Diagram on page 5.

7) Place the woofer, with its grille, into

the opening.

8) While holding the speaker firmly in its

NPVOUJOHMPDBUJPOQMBDFUIFYJODI

pan-head mounting screws (with washers) and

snug in a criss-cross pattern, then tighten with a

hand screwdriver in a criss-cross pattern.

WOOFER INSTALLATION PROCEDURE

Diagram C shows the typical installation

procedure into a fiberglass panel, using the

supplied hardware

$MBTTJD(SJMMF.PEFMTIPXO

*OTUBMMBUJPOJTUIFTBNFGPS4QPSU(SJMMF.PEFMT

Always follow proper safety procedures Use eye-

protection at all times and a dust mask and gloves

when cutting.

1) Choose a flat mounting surface that has sufficient

depth and air space behind it to accept the

component woofer.

2) Cut a 6.25-inch (159 mm) diameter hole.

3) Run the speaker cable from the amplifier

output to the mounting location.

4) Place the woofer in the hole and mark the screw

hole locations using a sharp, pointed tool.

Diagram C

Fiberglass Thickness Recommended Pilot Hole Drill Size

0.125 in. (3.18 mm) or less 7/64 in. (2.78 mm) pilot hole

foam core / fiberglass sandwich 7/64 in. (2.78 mm) pilot hole

larger than 0.125 in. (3.18 mm) 1/8 in. (3.18 mm) pilot hole

#8 SCREW: PILOT HOLE RECOMMENDATIONS

Non-standard installations may require different

hardware. Always use marine-grade, stainless-steel

fasteners to ensure a secure, reliable installation.

JL AUDIO LIMITED WARRANTY USA

Marine Speaker Systems

+-"VEJPXBSSBOUTUIFTFTQFBLFST BOE DSPTTPWFSOFUXPSLTXIFSFBQQMJDBCMF UP CF GSFF PG EFGFDUTJO

materials and workmanship for a period of two (2) years from the original date of purchase.

This warranty is not transferable and applies only to the original purchaser from an authorized

+-"VEJPEFBMFS4IPVMETFSWJDFCFOFDFTTBSZVOEFSUIJTXBSSBOUZGPSBOZSFBTPOEVFUPNBOVGBDUVSJOH

EFGFDUPSNBMGVODUJPO+-"VEJPXJMMBUJUTEJTDSFUJPOSFQBJSPSSFQMBDFUIFEFGFDUJWFQSPEVDUXJUIOFXPS

remanufactured product at no charge.

Damage caused by the following is not covered under warranty: accident, misuse, abuse, product

modification or neglect, failure to follow installation instructions, unauthorized repair attempts,

misrepresentations by the seller. This warranty does not cover incidental or consequential damages and

does not cover the cost of removing or reinstalling the unit(s). Cosmetic damage due to accident or normal

wear and tear is not covered under warranty.

Any applicable implied warranties are limited in duration to the period of the express warranty as

provided herein beginning with the date of the original purchase at retail, and no warranties, whether

express or implied, shall apply to this product thereafter. Some states do not allow limitations on implied

warranties, therefore these exclusions may not apply to you. This warranty gives you specific legal rights,

and you may also have other rights which vary from state to state.

If you need service on your JL AUDIO product:

"MM XBSSBOUZ SFUVSOT TIPVME CF TFOU UP +- "VEJP GSFJHIU QSFQBJE UISPVHI BO BVUIPSJ[FE

+- "VEJP EFBMFS BOE NVTU CF BDDPNQBOJFE CZ QSPPG PG QVSDIBTF B DPQZ PG UIF PSJHJOBM TBMFT SFDFJQU

Direct returns from consumers or non-authorized dealers will be refused unless specifically authorized

CZ+-"VEJPXJUIBWBMJESFUVSOBVUIPSJ[BUJPOOVNCFS8BSSBOUZFYQJSBUJPOPOQSPEVDUTSFUVSOFEXJUIPVU

proof of purchase will be determined from the manufacturing date code. Coverage may be invalidated as

this date is previous to purchase date. Return only defective components. If one speaker fails in a system,

return only that speaker component, not the entire system. Non-defective items received will be returned

freight-collect. Customer is responsible for shipping charges and insurance in sending the product to

+-"VEJP'SFJHIUEBNBHFPOSFUVSOTJTOPUDPWFSFEVOEFSXBSSBOUZ

For Service Information in the U.S.A. please call:

JL Audio customer service: (954)443-1100

during normal business hours (Eastern Time)

JL Audio, Inc

10369 North Commerce Pkwy.

.JSBNBS'-

International Warranties:

Products purchased outside the United States of America are covered only

CZUIBUDPVOUSZTEJTUSJCVUPSBOEOPUCZ+-"VEJP*OD

Printed in USA +-.$$4@.5$4@@4,6

Andere Handbücher für M770-CCS

Inhaltsverzeichnis

Andere JL Audio Lautsprechersystem Handbücher

JL Audio

JL Audio C5-400cw Bedienungsanleitung

JL Audio

JL Audio Evolution C3-600 Bedienungsanleitung

JL Audio

JL Audio Stealthbox SB-S-BRZFRS/10TW3 Bedienungsanleitung

JL Audio

JL Audio M880-CCX-SG (LED) Bedienungsanleitung

JL Audio

JL Audio M650-CCX Bedienungsanleitung

JL Audio

JL Audio C5-525 Bedienungsanleitung

JL Audio

JL Audio M770-ETXv2 Bedienungsanleitung

JL Audio

JL Audio MX650-CCX Bedienungsanleitung

JL Audio

JL Audio Stealthbox SB-SC-XBG1/10W1v3 Bedienungsanleitung

JL Audio

JL Audio C2-650 Bedienungsanleitung

JL Audio

JL Audio C2-075ct Bedienungsanleitung

JL Audio

JL Audio C2-600 Bedienungsanleitung

JL Audio

JL Audio MX650-CCX Bedienungsanleitung

JL Audio

JL Audio C5-252x Bedienungsanleitung

JL Audio

JL Audio Slampak SB-POL-RGRRZR Bedienungsanleitung

JL Audio

JL Audio TR650-CSi Bedienungsanleitung

JL Audio

JL Audio M880-CCX Bedienungsanleitung

JL Audio

JL Audio C5-075ct Bedienungsanleitung

JL Audio

JL Audio Steathbox SB-D-QDRAMD/10TW1 Bedienungsanleitung

JL Audio

JL Audio M770-CCS Bedienungsanleitung

Beliebte Lautsprechersystem Handbücher anderer Marken

JVC

JVC CA-MXK5R Bedienungsanleitung

LG NB4532B Bedienungsanleitung

JVC

JVC CA-FSH100 Bedienungsanleitung

5Core

5Core Pro Series Bedienungsanleitung

EAW

EAW MQV1394e Bedienungsanleitung

Lynx

Lynx GXR-LA10A Bedienungsanleitung

iLive

iLive ITB066B Bedienungsanleitung

RDX

RDX QuickStation 4 Bedienungsanleitung

Electro-Voice

Electro-Voice S-122 Bedienungsanleitung

Sven

Sven SPS-619 GOLD Bedienungsanleitung

Pioneer

Pioneer CS-7070 Bedienungsanleitung

EAW

EAW UB82e Bedienungsanleitung

Sondpex

Sondpex Active Speaker System and Digital Music... Bedienungsanleitung

JVC

JVC NX-PN7 Bedienungsanleitung

Yamaha

Yamaha NX-A01 - Speaker Sys Bedienungsanleitung

SE Audiotechnik

SE Audiotechnik I-LINE Bedienungsanleitung

Gemini

Gemini WRX-843 Series Bedienungsanleitung

TCL

TCL 6100 Series Bedienungsanleitung