JL Audio Stealthbox SB-F-MUSCPE/12TW3 Bedienungsanleitung

INSTALLATION GUIDE

for the

SB-F-MUSCPE/12TW3

SKU# 94617

2015 - Up Ford Mustang Coupe

Thank you for choosing a JL Audio Stealthbox® for your automotive sound system.

With proper installation, your new vehicle-specific enclosed subwoofer system

will deliver years of listening pleasure.

We strongly recommend that you have your new Stealthbox® installed by your

authorized JL Audio dealer. The installation professionals employed by your

dealer have the necessary tools and experience to disassemble and reassemble

your vehicle properly. If you prefer to perform your own installation, please read

this installation guide completely before beginning the process.

If you choose to perform the installation yourself, it is absolutely vital

that the Stealthbox®be properly mounted to the vehicle according to

these instructions. Failure to mount the enclosure properly presents two

problems:

1) The sub-bass performance will suffer due to the movement of the

enclosure caused by the force exerted by the woofer(s).

2) A loose enclosure presents a serious safety hazard in the event of a

collision or sudden deceleration.

INSTALLATION

DIFFICULTY:

ESTIMATED TIME:

12 HOURS

Enclosure Type: Sealed

Driver Type: 12TW3-D4

Nominal Impedance: 2 ohms

Continuous Power Handling: 400 watts (RMS method)

Continued on Next Page

OUT

SB-F-MUSCPE/12TW3 INSTR_SKU# 011432

INCLUDED HARDWARE

Continued on Next Page

Page 2 • JL Audio, Inc., 2015

SB-F-MUSCPE/12TW3 INSTR_SKU# 011432

Not shown: 1 150834 Trim Panel

1 151507 Velcro Strip

POWER RECOMMENDATION

JL Audio recommends high quality ampliers such as the JL Audio XD600/1v2. The diagram below shows the recommended crossover settings for the XD600/1v2. For a detailed description of the

amplier settings, consult the owner’s manual for the amplier. If another amplier is being used, please reference this illustration and use similar settings on that amplier.

CONNECTIONS

Using quality power, signal, and speaker wire is essential in ensuring the performance of your Stealthbox®. JL Audio recommends using a 4 AWG power kit such as the XD-PCS4-1B for your

Stealthbox® amplier. Other kits are available should you be using more than one amplier. Signal wire such as the JL Audio Premium Audio Interconnect Cables should be used to provide signal for

both channels of the amplier. JL Audio reccomends using 12AWG speaker wire for subwoofers such as our XC-BCS12-25.

Continued on Next Page

Page 3 • JL Audio, Inc., 2015

SB-F-MUSCPE/12TW3 INSTR_SKU# 011432

Page 4 • JL Audio, Inc., 2015 Continued on Next Page

STEP 8

Remove the four indicated lower subwoofer

enclosure bracket bolts.

STEP 7

Pull the trunk liner away to gain access to the

subwoofer enclosure bracket.

STEP 6

Remove the two 13 mm bolts securing the

bottom of the factory subwoofer enclosure to

the subwoofer enclosure bracket. Remove the

T-40 Torx bolt securing the top of the factory

subwoofer enclosure to the subwoofer

enclosure bracket.

Unplug the subwoofer, and remove the

enclosure from the vehicle.

STEP 5

Note: Steps 5-13 are only necessary in

vehicles equipped with the factory

subwoofer. If vehicle does not have the

factory subwoofer, skip to Step 14.

Remove the three T-20 Torx screws securing

the lower trim panel to the factory subwoofer

enclosure, and remove the trim panel.

STEP 4

Remove the clip holding the top of the trunk

liner to the vehicle on the passenger side.

STEP 3

Carefully unclip the trunk sill panel, and

remove the panel from the vehicle.

Remove the cargo floor panel from the vehicle.

STEP 2

Remove the cargo net hooks from both sides

of the trunk sill panel.

STEP 1

Empty out the trunk of the vehicle.

Some models are not equipped with the

pictured factory subwoofer.

SB-F-MUSCPE/12TW3 INSTR_SKU# 011432

Page 5 • JL Audio, Inc., 2015 Continued on Next Page

STEP 16

Thread an M8 - 70 mm Set Screw into the other

factory threaded hole. Place a 1” OD x 1/2”

Steel Spacer over the screw, and thread the M8

- 70 mm Set Screw until the top is 1/4” above

the top of the 1” OD x 1/2” Steel Spacer.

STEP 15

Thread an M8 - 70 mm Set Screw into one of

the factory threaded holes. Place a 1” OD x

1/2” Steel Spacer over the screw, and thread

the M8 - 70 mm Set Screw until the top is 1/4”

above the top of the 1” OD x 1/2” Steel Spacer.

STEP 14

Note: Steps 14-18 are only necessary in

vehicles not equipped with the factory

subwoofer. If vehicle does have the factory

subwoofer, skip to Step 19.

Lift up the trunk liner, and locate the two

factory threaded holes in the floor.

STEP 13

Press the Plastic Plug into the factory hole in

the floor.

Use a heat gun to soften the Plastic Plug,

allowing it to take the shape of the factory

hole. It may be necessary to add silicone

adhesive to hold the Plastic Plug in place.

STEP 12

Fold the trunk liner flap out of the way to

expose the other factory threaded hole in the

floor.

Thread an M8 - 70 mm Set Screw into the

factory threaded hole. Place a 1” OD x 1/2”

Steel Spacer over the screw, and thread the M8

- 70 mm Set Screw until the top is flush with

the 1” OD x 1/2” Steel Spacer.

STE P 11

Fold the trunk liner flap out of the way to

expose one of the factory threaded holes in

the floor.

Thread an M8 - 70 mm Set Screw into the

factory threaded hole. Place a 1” OD x 1/2”

Steel Spacer over the screw, and thread the M8

- 70 mm Set Screw until the top is flush with

the 1” OD x 1/2” Steel Spacer.

STEP 10

Remove the subwoofer enclosure bracket from

the vehicle.

STEP 9

Remove the indicated upper subwoofer

enclosure bracket bolt.

SB-F-MUSCPE/12TW3 INSTR_SKU# 011432

Page 6 • JL Audio, Inc., 2015 Continued on Next Page

STEP 24

Remove the subwoofer from the Stealthbox®.

Connect speaker cable to the terminal cup on

the enclosure, and route the cable as

necessary.

Guide the rear of the enclosure into position

first, allowing the 3/8 - 16 x 2-1/2” Set Screw to

pass through the hole in the back of the

enclosure.

STEP 23

Pictured is the 3/8 - 16 x 2-1/2” Set Screw with

the trunk liner back in place.

STEP 22

Place a 1” OD x 1/2” Steel Spacer over the 3/8

- 16 x 2-1/2” Set Screw, press the trunk liner

down, allowing the screw to pass through the

cut made in the trunk liner in the previous step.

STEP 21

Press the top of the trunk liner down against

the 3/8 - 16 x 2-1/2” Set Screw, and cut a small

“X” in the trunk liner over the screw.

STEP 20

Thread the 3/8 - 16 x 2-1/2” Set Screw into the

3/8 - 16 U-Nut as far as it will go.

STEP 19

Note: Steps 19-27 are necessary for all

models.

Slide a 3/8 - 16 U-Nut over the hole in the brace

near the passenger side taillight harness, as

shown.

If a factory U-nut is already installed in this

location, it will need to be removed and

replaced with the 3/8 - 16 U-Nut.

STEP 18

Push the trunk liner into position, allowing the

two M8 - 70 mm Set Screws to pass through

the cuts made in the trunk liner in the previous

step.

STEP 17

Fold the trunk liner back down against the M8

- 70 mm Set Screws, and cut a small “X” in the

trunk liner over each of the screws.

SB-F-MUSCPE/12TW3 INSTR_SKU# 011432

Page 7 • JL Audio, Inc., 2015

MID/HIGH FREQUENCY DRIVER FITMENT

A variety of JL Audio coaxial and component systems will t in the factory speaker locations of you vehicle.

Front Speaker Size / Location: 6-1/2”- Front Doors

Fits JL Audio Models: TR650-CXi, TR650-CSi, C2-650x, C2-650,

C3-650, C5-650x, C5-650, & ZR650-CSi

Rear Speaker Size / Location: 6-1/2”- Rear Door

Fits JL Audio Models: TR650-CXi, TR650-CSi, C2-650x, C2-650,

C3-650, C5-650x, C5-650, & ZR650-CSi

All specifications are subject to change without notice. “JL Audio®”and the JL Audio logo, and “Stealthbox” and the Stealthbox logo are registered trademarks of JL Audio, Inc.,. “Ahead of the

Curve”, its respective logo, and“How we play” are trademarks of JL Audio, Inc.,.

#6,625,292 #D472,891 #D480,709 Other U.S. & Foreign patents pending. For more detailed information please visit us online at www.jlaudio.com.

(954) 443-1100

www.jlaudio.com

JLA-SKU# 011432 • ver. 05.12.2015 • 10369 NORTH COMMERCE PARKWAY • MIRAMAR, FLORIDA • 33025 • USA

CONGRATULATIONS!

You have completed the installation for this model! Enjoy your new Stealthbox®!

How we play.™

SB-F-MUSCPE/12TW3 INSTR_SKU# 011432

STEP 28

Note: Step 28 is only necessary in

vehicles equipped with the factory

subwoofer.

Apply Velcro to the bottom of the trim panel as

shown, and secure it to the trunk floor in front

of the Stealthbox®.

STEP 27

Reinstall the subwoofer. Reinstall the trunk

liner clip above the Stealthbox®. Reinstall the

trunk sill panel, cargo net hooks, and trunk

floor panel.

STEP 26

Slide a 3/8” x 1-1/4” Fender Washer, a 3/8” Flat

Washer, a 3/8” Lock Washer, and a 3/8 - 16 Nut

over the 3/8 - 16 x 2-1/2” Set Screw at the back

of the enclosure.

Slide an M8 - 24 mm Washer, an M8 - 16 mm

Washer, an M8 Lock Washer, and an M8 - 1.25

mm Nut over each of the M8 - 70 mm Set

Screws at the bottom of the enclosure.

Tighten all hardware.

STEP 25

Guide the enclosure into position, aligning the

two holes in the bottom of the enclosure with

the two M8 - 70 mm Set Screws.

Back out the two M8 - 70 mm Set Screws,

allowing them to pass through the holes in the

bottom of the enclosure, until approximately

3/4” is exposed.

Andere JL Audio Sprecher Handbücher

JL Audio

JL Audio M6-650X Bedienungsanleitung

JL Audio

JL Audio VR690-CXi Bedienungsanleitung

JL Audio

JL Audio TR650-CXI Bedienungsanleitung

JL Audio

JL Audio C1-650 Bedienungsanleitung

JL Audio

JL Audio TR525-CXi Bedienungsanleitung

JL Audio

JL Audio PS-SWMCP Bedienungsanleitung

JL Audio

JL Audio TR570-CXi Bedienungsanleitung

JL Audio

JL Audio PAVILION PV-FX6 Bedienungsanleitung

JL Audio

JL Audio Fathom f112 Bedienungsanleitung

JL Audio

JL Audio C1-650X Bedienungsanleitung

JL Audio

JL Audio C1-400 series Bedienungsanleitung

JL Audio

JL Audio TR650-CXi Bedienungsanleitung

JL Audio

JL Audio M6-650 Series Bedienungsanleitung

JL Audio

JL Audio C7-350cm Bedienungsanleitung

JL Audio

JL Audio C1-075ct Bedienungsanleitung

JL Audio

JL Audio TR570-CXi Bedienungsanleitung

JL Audio

JL Audio C2-075ct Bedienungsanleitung

JL Audio

JL Audio M3-770x Bedienungsanleitung

JL Audio

JL Audio C1-690X Bedienungsanleitung

JL Audio

JL Audio M6-103EWS-Gw-C-GwGw-R Bedienungsanleitung

JL Audio

JL Audio C5-570 Bedienungsanleitung

JL Audio

JL Audio JLTR400CXi Bedienungsanleitung

JL Audio

JL Audio TR050-CT Bedienungsanleitung

JL Audio

JL Audio STEALTHBOX SB-POL-SLINGSPKR/M770 Bedienungsanleitung

Beliebte Sprecher Handbücher anderer Marken

argon audio

argon audio IE20 Bedienungsanleitung

Denon

Denon SC-N7 Bedienungsanleitung

Gemline

Gemline Ace 3952 Bedienungsanleitung

Focal

Focal ON WALL 300 Bedienungsanleitung

HEADRUSH

HEADRUSH Maximus HRSP 5024 Bedienungsanleitung

SoundLogic

SoundLogic BCCS-6/6395 Bedienungsanleitung

Peavey

Peavey DTH 218 Bedienungsanleitung

Avantree

Avantree Pluto Air Bedienungsanleitung

Morel

Morel Integra Series INTEGRA OVATION 4 Bedienungsanleitung

Oppo

Oppo SONICA Bedienungsanleitung

Bose

Bose SoundLink Wireless Music System Bedienungsanleitung

Rocksteady

Rocksteady Stadium Bedienungsanleitung

Bowers & Wilkins

Bowers & Wilkins 4 Bedienungsanleitung

Sonance

Sonance SONOS OUTDOOR Series Bedienungsanleitung

Electro-Voice

Electro-Voice EVID FM4.2 Bedienungsanleitung

Pioneer

Pioneer XW-HTD630 Bedienungsanleitung

Onn

Onn BWA16AA002 Bedienungsanleitung

HP GL313AA - USB Speakers PC Multimedia Bedienungsanleitung