JL Audio Stealthbox SB-J-GCHER3/10W1v2 Bedienungsanleitung

INSTALLATION GUIDE

for the

SB-J-GCHER3/10W1v2

2005 - Up Jeep Grand Cherokee

Thank you for choosing a JL Audio Stealthbox®for your automotive sound system. With proper

installation, your new vehicle-specific enclosed subwoofer system will deliver years of listening pleasure.

We strongly recommend that you have your new Stealthbox®installed by your authorized JL Audio

dealer. The installation professionals employed by your dealer have the necessary tools and experience

to disassemble and reassemble your vehicle properly. Also, keep in mind that your warranty coverage

extends to 2 years if your system is installed or approved by your authorized JL Audio dealer. If you

prefer to perform your own installation, please read this installation guide completely

before beginning the process.

If you choose to perform the installation yourself, it is absolutely vital that

the Stealthbox®be properly mounted to the vehicle according to these

instructions. Failure to mount the enclosure properly presents two problems:

1) The sub-bass performance will suffer due to the movement of the enclosure

caused by the force exerted by the woofer(s).

2) A loose enclosure presents a serious safety hazard in the event of a collision

or sudden deceleration.

STEP 1

Remove any contents from the cargo area.

Continued on Next Page

STEP 2

With a Phillips screw driver, remove the woofer from the

Stealthbox®.

Place the Stealthbox® onto the right side

wheel well/side panel (mounting location).

With a pencil or marker, mark the location of the mounting

hole onto the side panel from inside the Stealthbox®.

STEP 3

Remove the Stealthbox® from the vehicle.

With an 3/8” drill bit and drill, drill a hole through the side

plastic panel at the marked location from STEP 2.

There is a metal side panel that is located about 4” behind

this plastic side panel. The metal side panel also needs to be

drilled with the 3/8” drill bit. If the drill bit being used is more

then 4” long, then once you’re through the plastic panel you

can then mark or drill through the metal panel.

If your drill bit is not long enough. Mark onto the metal panel

with a pencil or marker, through the hole that was drilled

through the plastic panel.

SB-J-GCHER3/10W1v2_INSTR_SKU#011235

INSTALLATION

DIFFICULTY:

OUT

ESTIMATED TIME:

12 HOURS

Continued on Next Page

SB-J-GCHER3/10W1v2_INSTR_SKU#011235

STEP 7

With a small flat head screw driver, pop off the small cover

that is located on the top half of the c-pillar.

With Phillips head screw driver, remove the screw that has

been exposed.

Remove this top half of the c-pillar.

STEP 6

Remove the flooring from the vehicle.

STEP 5

Remove the false floor.

Remove the two mounting bolts that secure the flooring to

the vehicle.

STEP 4

Remove the tailgate’s bottom sill plate.

Page 2 • JL Audio, Inc 2007

STEP 9

With a Phillips head screw driver, remove the screw from the

rear section of the plastic panel.

STEP 11

Remove the tailgate’s upper sill plate.

STEP 10

With an hex key, remove the screw and D-ring from the rear

section of the plastic panel.

STEP 8

With a Phillips head screw driver, remove the screw from the

front section of the plastic side panel.

Continued on Next Page

SB-J-GCHER3/10W1v2_INSTR_SKU#011235

STEP 15

If needed, with the 3/8” drill bit and drill. Drill the metal panel

were it was marked from STEP 3.

*WARNING*

The metal behind this side panel is the outer metal of the

vehicle.

STEP 14

Remove the plastic panel from the vehicle.

STEP 13

Remove the right rear door’s sill plate.

STEP 12

Remove the d-pillar plastic cover.

VEHICLE SHEET METAL

SOCKET CUP SET SCREW

HEX BOLT

LOCK WASHER

STEALTHBOX WALL

COUPLERS

HEX NUT

LOCK WASHER

FLAT WASHER

SOCKET CUP SET SCREW

FLAT WASHER

Page 3 • JL Audio, Inc 2007

STEP 17

Place the hex bolt assembly through the drilled hole, from

the back side of the metal panel.

Apply a wrench onto the coupler that is in front of the metal

side panel.

Apply a 9/16-inch open end wrench to the hex bolt that is

behind the metal panel.

Secure the mounting assembly to the metal side panel.

STEP 19

Place the plastic side panel back into place. Guide the socket

cup set screw through the drilled hole. Only the socket cup

set screw should protrude through the plastic panel.

STEP 18

From the back side of the plastic side panel, cut out and

remove the sound deadening that is around the drilled hole.

STEP 16

The illustration to the left shows how all the supplied

hardware makes up the mounting assembly.

Place a lock washer and then flat washer onto the hex bolt.

Place both coupler nuts onto one socket cup set screw.

Make sure that there is enough room inside one of the

couplers to allow the hex bolt to be properly inserted, look

to STEP 17.

Fully thread in the second socket cup set screw into the

other coupler.

Continued on Next Page

SB-J-GCHER3/10W1v2_INSTR_SKU#011235

STEP 23

Place the right rear door’s sill plate back into place, from

STEP 13.

STEP 22

Wire and mount the woofer back into the Stealthbox®.

STEP 21

Place the Stealthbox® into the mounting area. Guide the

exposed socket cup set screw through the hole on the back

side of the Stealthbox®.

Place a supplied fender washer, flat washer, lock washer and

hex nut onto the socket cup set screw that is exposed inside

the Stealthbox®.

STEP 20

Run speaker wire from the amplifier location to the

Stealthbox® location.

Page 4 • JL Audio, Inc 2007

STEP 25

Secure the tailgate’s bottom sill plate back into place, from

STEP 4.

STEP 27

Secure the d-pillar cover back into place, from STEP 12.

STEP 26

Place the false floor back into the vehicle, from STEP 5.

STEP 24

Place the flooring back into the vehicle from STEPS 5&6,

and secure.

SB-J-GCHER3/10W1v2_INSTR_SKU#011235

CONGRATULATIONS

You have completed the installation for this model!

Please refer to the Power Recommendation section for an

amplifier recommendation and basic set-up help.

STEP 30

With a Phillips head screw driver, secure the screw that was

removed in STEP 9.

STEP 29

Secure the c-pillar cover back into place.

With a Phillips head screw driver, secure the screw and the

little cover that was removed in STEP 7.

STEP 28

With a Phillips head screw driver, secure the screw that was

remove in STEP 9.

The D-ring is not to be remounted.

Page 5 • JL Audio, Inc 2007

All specifications are subject to change without notice. “JL Audio®” and the JL Audio logo, “Stealthbox” and the Stealthbox logo are registered

trademarks of JL Audio, Inc.“Ahead of the Curve” and its respective logo is a trademark of JL Audio, Inc.

JLA-SKU#011235 6-13-200

#6,294,959 #6,501,844 #6,496,590 #6,441,685 #5,687,247 #6,219,431 #6,625,292 #D472,891 #D480,709 Other U.S. & Foreign patents pending.

For more detailed information please visit us online at www.jlaudio.com.

(954) 443-1100

www.jlaudio.com

10369 NORTH COMMERCE PARKWAY • MIRAMAR, FLORIDA • 33025 • USA

INCLUDED HARDWARE

(1)

3/8-inch-16 x 1-inch Hex Tap Bolt

(1)

3/8-inch x 1-1/4-inch Fender Washer

(2)

Rod Coupling Nut (1) 3/8-inch-16 Hex Nut

(2)

3/8-inch Lock Washer (2) 3/8-inch-16 x 2-1/4-inch Socket Cup Set Screw

(2)

3/8-inch-16 x 2-1/4-inch Socket Cup Set Screw

SPECIFICATIONS

Enclosure Type:

Acoustic Suspension (sealed)

Driver Type:

10W1v2

Nominal Impedance:

4 ohms mono

Continuous Power Handling:

150 Watts

150 Wat ts

P O W E R R E C O M M E N D A T I O N

POWER RECOMMENDATION

JL Audio recommends using a high quality amplifier such as the JL Audio A2150.

The diagram below shows the recommended crossover, infrasonic filter and equalizer settings for the A2150 when

being used to power your Stealthbox®.

The JL Audio A2150 is a very versatile audio component. Please consult the owner’s manual for even more

detailed information about installing and tuning this amplifier.

MID/HIGH FREQUENCY DRIVER FITMENT

A variety of JL Audio coaxial and component systems will fit in the factory speaker locations of you vehicle.

Front Speaker Size / Location:

3.5-inch / Dash

Fits JL Audio Models:

TR350-CXi

Front Speaker Size / Location:

6-inch x 9-inch / Front Doors

Fits JL Audio Models:

*TR690-TXi & *VR690-CXi

Rear Speaker Size / Location:

6.5-inch / Rear Door

Fits JL Audio Models:

TR650-CXi, VR650-CXi, *XR650-CXi & *C5-650x

*Spacers required for proper speaker installation.

Dieses Handbuch passt für folgende Modelle

Andere JL Audio Subwoofer Handbücher

JL Audio

JL Audio Stealthbox SB-POL-RNGR/SYS Bedienungsanleitung

JL Audio

JL Audio Stealthbox SB-SC-XB/10W3v3-4 Bedienungsanleitung

JL Audio

JL Audio 12W1v2-4 Bedienungsanleitung

JL Audio

JL Audio 12TW3 Bedienungsanleitung

JL Audio

JL Audio Stealthbox SB-GM-C6CONV/8W3v3 Bedienungsanleitung

JL Audio

JL Audio 10W6v3 Bedienungsanleitung

JL Audio

JL Audio 10W0 Bedienungsanleitung

JL Audio

JL Audio SB-VW-JETSW/10W3v3 Bedienungsanleitung

JL Audio

JL Audio Fathom f212 Bedienungsanleitung

JL Audio

JL Audio 12TW3-D4 Bedienungsanleitung

JL Audio

JL Audio 15W1-4 Bedienungsanleitung

JL Audio

JL Audio M12IB6 Bedienungsanleitung

JL Audio

JL Audio 12WX Bedienungsanleitung

JL Audio

JL Audio M10W5 Bedienungsanleitung

JL Audio

JL Audio Stealthbox SB-N-ARMAD/10W6v2 Bedienungsanleitung

JL Audio

JL Audio fathom v2 Bedienungsanleitung

JL Audio

JL Audio Stealthbox SB-VW-GTI/10TW3 Bedienungsanleitung

JL Audio

JL Audio 300/2 Bedienungsanleitung

JL Audio

JL Audio Fathom IWS-SYS-2 Bedienungsanleitung

JL Audio

JL Audio 10TW3-D8 Bedienungsanleitung

JL Audio

JL Audio Stealthbox SB-GM-SLVD4/10TW3 Bedienungsanleitung

JL Audio

JL Audio M3-10IB Bedienungsanleitung

JL Audio

JL Audio Stealthbox SB-GM-TRLBLZR/10W3v3 Bedienungsanleitung

JL Audio

JL Audio Stealthbox SB-J-GRCHER/10W1 Bedienungsanleitung

Beliebte Subwoofer Handbücher anderer Marken

Sony

Sony XS-AW8 Bedienungsanleitung

Sony

Sony XS-L836 Bedienungsanleitung

B&C Speakers

B&C Speakers 15 HPL 76W Bedienungsanleitung

Velodyne

Velodyne DD-18+ Bedienungsanleitung

Sonance

Sonance Cinema Series SUB 10-150 Bedienungsanleitung

Hifonics

Hifonics HW-12 Kurzanleitung

Magnat Audio

Magnat Audio ADR 130 BP Bedienungsanleitung

Blitz

Blitz BZP106 Bedienungsanleitung

Technics

Technics SB-AS500 Bedienungsanleitung

Lyngdorf

Lyngdorf BW-2 Bedienungsanleitung

Lyngdorf

Lyngdorf BW-3 Bedienungsanleitung

Pyle Pro

Pyle Pro PYLE PRO PDW15125 Bedienungsanleitung

REL Acoustics

REL Acoustics Q Series Bedienungsanleitung

L-Acoustics

L-Acoustics KIVA SB15M Kurzanleitung

Pioneer

Pioneer Elite S-W1EX Bedienungsanleitung

B&C Speakers

B&C Speakers Woofer 12 HPL 76 Bedienungsanleitung

KEF

KEF KUBE 200 Bedienungsanleitung

Yamaha

Yamaha SW500 Bedienungsanleitung