JL Audio Stealthbox SB-P-CYNNE/10W6v2/BK Bedienungsanleitung

INSTALLATION GUIDE

for the

SB-P-CYNNE/10W6v2/BK

2003 - 2006

Porsche Cayenne

Thank you for choosing a JL Audio Stealthbox®for your automotive sound system. With proper

installation, your new vehicle-specific enclosed subwoofer system will deliver years of listening pleasure.

We strongly recommend that you have your new Stealthbox®installed by your authorized JL Audio

dealer. The installation professionals employed by your dealer have the necessary tools and experience

to disassemble and reassemble your vehicle properly. Also, keep in mind that your warranty coverage

extends to 1 year if your system is installed or approved by your authorized JL Audio dealer. If you

prefer to perform your own installation, please read this installation guide completely

before beginning the process.

If you choose to perform the installation yourself, it is absolutely vital that

the Stealthbox®be properly mounted to the vehicle according to these

instructions. Failure to mount the enclosure properly presents two problems:

1) The sub-bass performance will suffer due to the movement of the enclosure

caused by the force exerted by the woofer(s).

2) A loose enclosure presents a serious safety hazard in the event of a collision

or sudden deceleration.

STEP 1

Remove any contents from the cargo area.

Continued on Next Page

STEP 2

Remove the flooring.

STEP 3

With a T-30 wrench or socket, remove the pair of hold down

cleats(A).

With an 10mm socket, remove the bolt(B) that secures the

side panel to the vehicle.

SB-P-CYNNE/10W6v2/BK_INSTR_SKU#011231

INSTALLATION

DIFFICULTY:

OUT

ESTIMATED TIME:

23 HOURS

Continued on Next Page

SB-P-CYNNE/10W6v2/BK_INSTR_SKU#011231

STEP 7

Remove the plastic cover from the upper d-pillar trim.

Remove the phillip head screw that has been exposed .

STEP 6

Remove the top sill plate.

STEP 5

Remove the lower d-pillar trim.

STEP 4

Remove the bottom sill plate.

Page 2 • JL Audio, Inc 2007

STEP 9

With a T-30 socket, remove the bolt and metal bracket that

is located between the two rear seats.

STEP 11

Flip the driver’s side rear bottom cushion towards the front

of the vehicle.

STEP 10

Grab a hold of the back of the driver’s side rear seat as in

the picture.

Lift the right side of the seat up and out of the hinge

bracket.

Pull the left side of the seat towards the middle of the

vehicle, sliding the seat off of a hinge pin.

Once the seat is off both hinge points, remove the seat

from the vehicle.

STEP 8

Remove the upper d-pillar trim.

Continued on Next Page

SB-P-CYNNE/10W6v2/BK_INSTR_SKU#011231

STEP 15

Remove the plastic ring from the rear seat’s upper latch pin.

STEP 14

With a 17mm socket and ratchet, remove the seat belt

retracting unit.

STEP 13

Remove the trim panel.

STEP 12

Remove the plastic collar that is around the hinge pin.

Page 3 • JL Audio, Inc 2007

STEP 17

An airbag is located behind the c-pillar trim. Use caution

while removing this panel. All wiring/connections should be

protected.

As in the illustration, reach around to the rear of the c-pillar

trim and carefully remove the c-pillar trim from the c-pillar,

by pulling towards you.

STEP 19

From the driver’s side rear door opening. Pull the front of the

cargo side trim panel from the vehicle’s body. Do not fully

remove this side trim panel at this time.

STEP 18

With a T-25 socket remove the bolt that secures the front

of the side trim panel to the c-pillar.

STEP 16

Pull the SRS plastic badge from the upper c-pillar trim.

With a T-25 socket, remove the bolt that has been

exposed.

Continued on Next Page

SB-P-CYNNE/10W6v2/BK_INSTR_SKU#011231

STEP 23

With a T-30 socket, remove the bolts that secure the pocket

to the body of the vehicle.

STEP 22

Pull the side trim panel out of vehicle.

STEP 21

Pull the rest of the side trim panel from the body of the

vehicle.

Once the side trim panel is loose, disconnect the power

outlet 12V plug from the wire harness.

STEP 20

With a T-25 socket, remove three bolts that secures this

rear side trim panel.

Page 4 • JL Audio, Inc 2007

STEP 25

Place the supplied top mount plate into position. The plate

will only fit one way. The hole in the mounting plate will line

up with the access hole from the removed grommet.

STEP 27

Thread in one of the supplied socket cup set screws into the

bottom of the Stealthbox®, leaving 1-inch exposed.

STEP 26

Run speaker wire from the amplifier’s location to the

Stealthbox®location and check for proper operation of

the woofer.

STEP 24

Found in the rearmost driver’s side floor corner, remove

the rubber grommet in the cargo area.

Unsecure the wire harness from the wheel well.

*Make sure the ignition is not turned on*

Loosen the bolt that secures the brown wires to the

flooring of the vehicle.

Once loose, turn this wire assembly counter clockwise until

the wires are routed as illustrated in the picture. Secure the

bolt.

VEHICLE SHEET METAL

SOCKET CUP SET SCREW

HEX BOLT

BOTTOM MOUNTING PLATE

LOCK WASHER

FLAT WASHER

STEALTHBOX WALL THREADED INSERT

SOCKET CUP SET SCREW

TOP MOUNTING PLATE

COUPLER

Continued on Next Page

SB-P-CYNNE/10W6v2/BK_INSTR_SKU#011231

STEP 31

Place a supplied 3/8-inch lock washer and then a supplied

flat washer onto the supplied 3/8-inch bolts.

Place two of these mounting bolt assemblies through the

supplied L-bracket. The L-bracket can only be posistioned

one way. Line up the mounting holes of the L-bracket to the

threaded inserts of the Stealthbox®.

Place the L-bracket into the mounting position and guide the

bolt assemblies through the two holes in the metal lip, as

seen in the picture to the left.

Place a supplied flat washer and supplied hex nut onto each

protruding bolt, behind the metal lip.

With an 9/16-inch box end wrench holding the nuts, use a

9/16-inch socket to secure the L-bracket to the metal lip.

STEP 30

Once the Stealthbox® is in position, place the supplied piece

of black carpeting between the Stealthbox® and the rear side

of the wheel well. You need to cover the corner of the wheel

well just in front of the Stealthbox®.

STEP 29

Place the Stealthbox®into position by guiding the socket

cup set screw assembly through the hole in the top

mounting plate installed in STEP 25.

The bottom of the Stealthbox® will not touch the mounting

plate. The coupler will be touching the mounting plate.

STEP 28

Fully thread the supplied coupler to the first socket cup set

screw from STEP 27.

Thread the second supplied socket cup set screw into the

coupler.

Page 5 • JL Audio, Inc 2007

STEP 33

From under the vehicle, place the supplied mounting plate,

flat washers, lock washers and then hex nut onto the

protruding socket cup set screw. Using an 9/16-inch socket,

secure this bottom mounting assembly.

Note: For added protection, it is recommended that

you apply a bead of silicone between the vehicle and

the mounting plate. After the bolt assembly is tightly

secured, it is also recommended that vehicle under-

coating material is applied to the exposed assembly.

STEP 35

Reconnect the power outlet 12V plug to the wire harness,

unplugged in STEP 22.

STEP 34

Place the factory side trim panel, removed in STEP 22, back

into place.

STEP 32

With a 9/16-inch socket and the remaining supplied pair of

bolt assemblies, secure the L-bracket to the Stealthbox®.

Continued on Next Page

SB-P-CYNNE/10W6v2/BK_INSTR_SKU#011231

STEP 39

Replace the trim and the plastic collar that goes around the

hinge pin, from STEP 12 & 13.

STEP 38

With a 17mm socket, secure the seat belt retracting unit,

from STEP 14.

STEP 37

With a T-25 socket, secure the front of the side trim panel

to the c-pillar, from STEP 18.

STEP 36

With a T-25 socket, secure the rear of the side trim panel

to the d-pillar, from STEP 20.

Page 6 • JL Audio, Inc 2007

STEP 41

Secure the upper d-pillar trim to the d-pillar, secure the trim

with the mounting screw that was removed and repalce the

plastic cover, from STEPS 7 & 8.

STEP 43

Replace the lower d-pillar trim, from STEP 5.

STEP 42

Replace the top sill plate, from STEP 6.

STEP 40

With a T-25 socket, secure the top c-pillar trim to the

c-pillar, from STEPS 16 & 17.

SB-P-CYNNE/10W6v2/BK_INSTR_SKU#011231

STEP 47

Replace the flooring and any contents, from STEP 1 & 2.

CONGRATULATIONS

You have completed the installation for this model!

Please refer to the Power Recommendation section for an

amplifier recommendation and basic set-up help.

STEP 46

Replace the rear seat removed in STEP 9 & 10.

STEP 45

With a T-30 wrench or socket, mount the pair of hold down

cleats(A), from STEP 3.

With a 9mm socket, mount the bolt(B) that secures the side

panel to the vehicle, from STEP 3.

STEP 44

Replace the cargo door sill plate, from STEP 4.

Page 7 • JL Audio, Inc 2007

All specifications are subject to change without notice. “JL Audio®” and the JL Audio logo, “Stealthbox” and the Stealthbox logo are registered

trademarks of JL Audio, Inc.“Ahead of the Curve” and its respective logo is a trademark of JL Audio, Inc.

JLA-SKU#011231-04-23-200

#6,243,479 #6,294,959 #6,501,844 #6,496,590 #6,441,685 #5,687,247 #6,219,431 #6,625,292 #D472,891 #D480,709 Other U.S. & Foreign

patents pending. For more detailed information please visit us online at www.jlaudio.com.

(954) 443-1100

www.jlaudio.com

10369 NORTH COMMERCE PARKWAY • MIRAMAR, FLORIDA • 33025 • USA

INCLUDED HARDWARE

(2)

3/8-inch -16 x 2 1/4-inch Socket Cup Set Screws

(7)

3/8-inch Flat Washer

(1)

3/8-inch -16 Socket Cup Set Screw Coupler

(5)

3/8-inch Lock Washer

(1)

Aluminum Top Mounting Plate

(4)

3/8-inch -16 x 1 1/4-inch Hex Bolts

(1)

Aluminum Bottom Mounting Plate

(3)

3/8-inch -16 Hex Nuts

SPECIFICATIONS

Enclosure Type:

Acoustic Suspension (sealed)

Driver Type:

10W6v2-D4

Nominal Impedance:

2 ohms mono

Continuous Power Handling:

400 Watts

POWER RECOMMENDATION

JL Audio recommends using a high quality amplifier such as the JL Audio 500/1.

The diagram below shows the recommended crossover, infrasonic filter and equalizer settings for the 500/1 when

being used to power your Stealthbox®.

+12VDC RemoteGround

JL AUDIO 500/1

five-channel system amplifier

Subwoofer Output

MONO OUTPUT ONLY

55 65 85

120

200

Filter Freq. (Hz)

Mode / Slope

Off / 12dB / 24dB

Amp LP Filter

Infrasonic Freq. (Hz)

25 30 40

Off / 30Hz

Infrasonic Filter

0.5

0.7

1.1 1.6 2.7

4.3

"Q"

35 45 55

Center Freq.

+4 +10 +13

+15

Boost (dB)

Off / On

Bass EQ

Remote Bass Port

Advanced

Bass

Control

Preamp Output Section

Full Range / Amp Filter / Out Filter

Output Mode Filter Slope

12dB / 24dB

55 65 85

120

200

Filter Freq. (Hz)

Left Ch. Right Ch.

Filter Mode

LP / HP

Amplifier Input Section

Input Sens.

Left Ch. Right Ch.

Signal Sensing

Off / On

Input Voltage

Low / High

The JL Audio 500/1 is a very versatile audio component. Please consult the owner’s manual for even more

detailed information about installing and tuning this amplifier.

MID/HIGH FREQUENCY DRIVER FITMENT

A variety of JL Audio coaxial and component systems will fit in the factory speaker locations of you vehicle.

Front Speaker Size / Location:

6.5-inch / Front Doors

Fits JL Audio Models: TR650-CSi,

TR650-CXi, VR650-CSi, VR650-CXi, XR650-CSi, XR650-CXi,

C5-650, C5-650x & ZR650-CSi

Rear Speaker Size / Location:

6.5-inch / Rear Doors

Fits JL Audio Models:

TR650-CXi, VR

650

-CXi, C5-650x & XR

650

-CXi

Andere JL Audio Subwoofer Handbücher

JL Audio

JL Audio JL AUDIO 8W1v2-4 Bedienungsanleitung

JL Audio

JL Audio Stealthbox SB-H-RIDGLNE/10W3v3 Bedienungsanleitung

JL Audio

JL Audio Stealthbox SB-N-350/10W3v2 Bedienungsanleitung

JL Audio

JL Audio 10W6v3 Bedienungsanleitung

JL Audio

JL Audio 8W1v2-4 Bedienungsanleitung

JL Audio

JL Audio W7AE Bedienungsanleitung

JL Audio

JL Audio 12WOv3-4 Bedienungsanleitung

JL Audio

JL Audio Stealthbox SB-GM-CAM/10W3v3 Bedienungsanleitung

JL Audio

JL Audio M3-10IB Bedienungsanleitung

JL Audio

JL Audio Stealthbox SB-GM-ESCESV/10W1v3 Bedienungsanleitung

JL Audio

JL Audio MX101B3-SG Bedienungsanleitung

JL Audio

JL Audio Stealthbox SB-S-IMPRZA/10W6v2 Bedienungsanleitung

JL Audio

JL Audio 10W0v3-4 Bedienungsanleitung

JL Audio

JL Audio 12W3v3-2 Bedienungsanleitung

JL Audio

JL Audio Stealthbox SB-GM-CAM12W6v2 Bedienungsanleitung

JL Audio

JL Audio Stealthbox SB-GM-CFMINI/10W3v2 Bedienungsanleitung

JL Audio

JL Audio 300/2 Bedienungsanleitung

JL Audio

JL Audio 10TW3 Bedienungsanleitung

JL Audio

JL Audio M6-10IB Bedienungsanleitung

JL Audio

JL Audio Stealthbox SB-D-5GRAMCCF/12TW3 Bedienungsanleitung

JL Audio

JL Audio M8IB5 Bedienungsanleitung

JL Audio

JL Audio Stealthbox SB-F-F1502/10W3v3 Bedienungsanleitung

JL Audio

JL Audio Stealthbox SB-H-S2000/10W3 Bedienungsanleitung

JL Audio

JL Audio 12W1-4 Bedienungsanleitung

Beliebte Subwoofer Handbücher anderer Marken

Sony

Sony XS-AW8 Bedienungsanleitung

Sony

Sony XS-L836 Bedienungsanleitung

B&C Speakers

B&C Speakers 15 HPL 76W Bedienungsanleitung

Velodyne

Velodyne DD-18+ Bedienungsanleitung

Sonance

Sonance Cinema Series SUB 10-150 Bedienungsanleitung

Hifonics

Hifonics HW-12 Kurzanleitung

Magnat Audio

Magnat Audio ADR 130 BP Bedienungsanleitung

Blitz

Blitz BZP106 Bedienungsanleitung

Technics

Technics SB-AS500 Bedienungsanleitung

Lyngdorf

Lyngdorf BW-2 Bedienungsanleitung

Lyngdorf

Lyngdorf BW-3 Bedienungsanleitung

Pyle Pro

Pyle Pro PYLE PRO PDW15125 Bedienungsanleitung

REL Acoustics

REL Acoustics Q Series Bedienungsanleitung

L-Acoustics

L-Acoustics KIVA SB15M Kurzanleitung

Pioneer

Pioneer Elite S-W1EX Bedienungsanleitung

B&C Speakers

B&C Speakers Woofer 12 HPL 76 Bedienungsanleitung

KEF

KEF KUBE 200 Bedienungsanleitung

Yamaha

Yamaha SW500 Bedienungsanleitung