Johnson Controls Penn P216 Series Bedienungsanleitung
P216 Series Condenser Fan Speed Controller Installation Instructions 1
Refer to the QuickLIT website for the most up-to-date version of this document.
Applications
Mounting
Location and Mounting Considerations
Observe these guidelines when locating and mounting
a P216 Series Fan Speed Controller:
• Ensure that the mounting surface and mounting
hardware can support the control and wiring.
• Mount the P216 Series controller upright on a
vertical surface with the heat sink fins oriented
vertically and the conduit/electrical holes facing
down.
Figure 1: P216 Condenser Fan Speed Controller
Mounting Dimensions, mm
• Ensure that air can flow through the heat sink fins
and provide 10 cm (4 in.) minimum clearance
around the heat sink.
• Mount the P216 Series controller in a location
away from sources of excessive heat and within
the specified ambient operating conditions.
See Technical Specification for ambient operating
conditions.
IMPORTANT: Use this P216 Series Condenser
Fan Speed Controller only as an operating control.
Where failure or malfunction of the P216 Series Fan
Speed Controller could lead to personal injury or
property damage to the controlled equipment or
other property, additional precautions must be
designed into the control system. Incorporate and
maintain other devices, such as supervisory or
alarm systems or safety or limit controls, intended to
warn of or protect against failure or malfunction of
the P216 Series Fan Speed Controller.
!
CAUTION: Risk of Property Damage
Use only single-phase Permanent Split
Capacitor (PSC) motors approved by the
manufacturer for speed control
application with the P216 Series
controller. Failure to use a single-phase
PSC motor may damage the motor and
other property.
165
178
76
66
P216 Series Condenser Fan Speed Controller
Installation Instructions
P216xxx-x Part No. 24-85895-18, Rev. D
Issued 27 August 2015
P216 Series Condenser Fan Speed Controller Installation Instructions2
Installation
Wiring
• Ensure that the wires between the P216 Series
controller and the fan motor do not exceed 100 m
(328 ft).
• Wires connected to the line-voltage terminal block
must be 3,31 mm2(12 AWG) or smaller.
• Low-voltage wires must be less than 30 m (100 ft).
Description
A DIP switch will be used to select one of 4 different
pressure ranges. There is one potentiometer to
manually adjust the setpoint.
• There is one potentiometer to manually adjust the
minimum speed.
• A green LED will indicate that power is applied.
• Two 3 position screw terminal blocks will be used
to connect the 50 bar transducers.
• A 3 position screw terminal block will be used to
select HP or Reverse modes.
• Contacts between HP and C will run the fan at full
speed.
• Contacts between REV and C will increase the fan
speed as pressure decreases (Reverse Operation).
ш50 mm
ш50 mm
ш50 mm
ш50 mm
P = 8 W max.
55 °C = 8 A max.
IP54
55 °C = 6 A max.
40 °C = 8 A max.
IP54
!
WARNING: Risk of Electric Shock.
Disconnect or isolate all power supplies
before making electrical connections.
More than one disconnect or isolation
may be required to completely
de-energize equipment. Contact with
components carrying hazardous voltage
can cause electric shock and may result
in severe personal injury or death.
IMPORTANT: Do not connect supply power to the
P216 Series controller before finishing wiring and
checking all wiring connections. Short circuits or
improperly connected wires can result in damage to
the P216 Series controller and void any warranty.
IMPORTANT: Do not exceed the P216 Series Fan
Speed Controller electrical ratings. Exceeding P216
Series controller electrical ratings can result in
permanent damage to the P216 Series controller
and void any warranty.
IMPORTANT: Use copper conductors only.
Make all wiring in accordance with local, national,
and regional regulations.
IMPORTANT: Electrostatic discharge can damage
P216 controller components. Use proper
Electrostatic Discharge (ESD) precautions during
installation and servicing to avoid damaging P216
components.
DIP Switch Block
LED
Setpoint
Min speed
M1 L1
L2/N
L2/N
HP C REV
Earth Ground
Connection
V
Power Supply
and Motor Terminal
Heatpump
and Reverse action
Terminal
P2 C
VP1C
Two Pressure
Transducers Inputs
20% 100%
-
+
P216 Series Condenser Fan Speed Controller Installation Instructions 3
There is a 4 position DIP switch to choose various setup configurations.
When Switch 3 is set to OFF, the Master Mode is selected and one or two P499VCS-405C Pressure Transducers
are used as inputs to change the speed of a fan motor. In Normal Operation, the maximum speed occurs when the
higher of the 2 pressure inputs is greater than or equal to the setpoint and the minimum speed occurs when the
pressure is equal to the setpoint minus the prop. band (see P216 Normal Operation Example).
In Reverse Operation (selected by connecting a jumper between the REV and C terminals), the minimum speed
occurs when the pressure is equal to the setpoint and the maximum speed occurs when the pressure is less than
or equal to the setpoint minus the prop. band.
When Switch position 3 is set to ON, the Slave Mode is selected and the Setpoint potentiometer defines the input
voltage level that causes the motor to run at full speed. For example, if the 2-10 Vdc Setpoint Range is selected
and the Setpoint potentiometer is adjusted completely to "+", then the motor will run at full speed when Vin = 10 Vdc.
If the Setpoint potentiometer is adjusted midway between "-" and "+", then the motor will run at full speed when
Vin = 6,0 Vdc (see P216 Slave Operation Example).
1234
ON
Min Speed Switch
ON
OFF
=
=
Motor never stops, always runs at Min Speed
or greater, depending on conditions.
Minimum Speed Feature is disabled.
Motor shuts completely off at low pressure.
P216 Operation
Using P499VCS-405C
Transducer Setpoint Range
CCW - CW
(BAR)
SW1 SW2 SW3
OFF OFF OFF
OFF
OFF OFF
OFF
ON
ON
ON ON
4 - 10
8 - 14
14 - 24
22 - 42
2,0
2,5
4,0
5,0
Proportional Band
(BAR)
Mode
OFF
Master
Master
Master
Master
P216 Operation
in Slave Mode
Note 1: The Proportional Band in Slave Mode Extends from 0 Vdc to the Setpoint Voltage.
Setpoint Range
CCW - CW
(Vdc)
SW1 SW2 SW3
OFF OFF ON
OFF ON
2 - 10 Vdc
1 - 5 Vdc
(See Note 1)
Proportional Band
(BAR)
Mode
ON
Slave
Slave
TB1
M1 L1 L2/N L2/N
VAC
Fan-Motor
Power Supply
208 - 240 Vac 50/60 Hz
P216 Series Condenser Fan Speed Controller Installation Instructions4
P216 Normal Operation Example using a 230 V Supply- Output Voltage vs Input Pressure
Note: Set switches 1-3 as shown to select a 14-24 Bar Setpoint range with a 4 Bar Proportional Band.
Adjust the Setpoint potentiometer to 20 Bar (which is 60% rotation from the "-" or CCW end of the Setpoint
potentiometer). Adjust the Min. Speed potentiometer completely CCW (to set the Min Speed to 20% of
230V or 46V). Setting Switch 4 to ON causes the motor to always run at minimum speed or greater.
P216, 0 - 10 Vdc Slave Operation Example using 230 V Supply - Output vs Input Voltage
Input (Pressure - Bar)
Output to Motor
(VAC)
16 Bar 20 Bar
Setpoint
220 V
Min. Speed 46 V
DIP Switch Block
Setpoint
60% from “-”
Min speed
20% 20% 100%
-
+
Proportional Band
1234
ON
0 V
Input (Voltage)
Output to Motor
(VAC)
6,0 Vdc
Setpoint
220 V
230 V*0,2 = 46 V
Setpoint
at midscale
Min speed
20% 20% 100%
-
+
Proportional Band
1234
ON
6,0 V*0,2 = 1,2 Vdc
20% Min Speed
Switch 4 = OFF
0 V
10,0 Vdc
Note 1: If Min Speed is set to 40%, then Output turns off at 230 V*0,4 = 92 VAC
when Input Voltage drops to 6,0 V* 0,4 = 2,4 Vdc.
DC Voltage Connection
VP1C
0 - 10 Vdc
Control Signal
See Note 1
-
+
P216 Series Condenser Fan Speed Controller Installation Instructions 5
P499 Electronic Pressure Transducers
P216 Series controllers are designed to reference
either one or two Johnson Controls P499 Electronic
Pressure Transducers to monitor condenser pressure.
On P216 Series controller applications that use two
P499 transducers, the P216 Series controller always
references the transducer that is sensing the higher
pressure.
P499VCS-405C, 0-50 bar, 0-10 Vdc Output,
Pressure Transducer
Only P499 models that have a 0-10 Vdc output signal
can be used with the P216 control.
IMPORTANT: Operate the P216 only in
combination with one or two P499VCS-405C
Pressure Transducers.
Wire Connection Terminal
Red V
Black C
White P
www.johnsoncontrols.com
P216 Series Condenser Fan Speed Controller Installation Instructions6
Metasys® and Johnson Controls® are registered trademarks of Johnson Controls, Inc.
All other marks herein are the marks of their respective owners. © 2011 Johnson Controls, Inc.
Building Efficiency
507 E. Michigan Street, Milwaukee, WI 53202
Building Efficiency
Headquarters: Milwaukee, Wisconsin, USA
Branch Officies: Principal Cities World-wide
® Johnson Controls and PENN are registered trademarks of Johnson Controls, Inc. in the
United States of America and/or other countries. All other trademarks used herein are the property
of their respective owners. © Copyright 2015 by Johnson Controls, Inc. All rights reserved.
Technical Specifications
The performance specifications are nominal and conform to acceptable industry standards. For application at conditions beyond these
specifications, consult the local Johnson Controls office. Johnson Controls, Inc. shall not be liable for damages resulting from misapplication or
misuse of its products.
P216xxx-x Condenser Fan Speed Controller
Input Signal 0 - 10 Vdc
Power Supply 208 - 240 Vac 50 - 60 Hz
Control Action Direct or reverse mode
Maximum Motor Current 12 Amp
Minimum Motor Current 0,5 Amp
Ambient Operating Conditions -40 to 60C (-40 to 140F)
Ambient Shipping and Storage
Conditions -40 to 85C (-40 to 185F)
Enclosure Type NEMA 3R, IP54
Dimensions (H x W x D) 159 x 177 x 70 mm (6-1/4 x 7 x 2-3/4 in.)
Weight 1,0 kg (2,2 lb)
Compliance Johnson Controls, Inc., declares that these products are in compliance with the essential
requirements and other relevant provisions of the EMC Directive 2004/108/EC,
Low Voltage Directive 2006/95/EC.
Inhaltsverzeichnis
Andere Johnson Controls Controller Handbücher
Johnson Controls
Johnson Controls LC-AVMHTC1-0 Bedienungsanleitung
Johnson Controls
Johnson Controls FX-PCV Series Bedienungsanleitung
Johnson Controls
Johnson Controls F4-CVM Bedienungsanleitung
Johnson Controls
Johnson Controls PENN P70 Series Bedienungsanleitung
Johnson Controls
Johnson Controls FX-PCV1656 Bedienungsanleitung
Johnson Controls
Johnson Controls M9220-GGx-3 series Bedienungsanleitung
Johnson Controls
Johnson Controls M4-CV Series Bedienungsanleitung
Johnson Controls
Johnson Controls FX Supervisory Controller RS-485 Card Bedienungsanleitung
Johnson Controls
Johnson Controls M9310-HGA-3 Bedienungsanleitung
Johnson Controls
Johnson Controls PENN P70 Series Bedienungsanleitung
Johnson Controls
Johnson Controls M9108-A-1N Series Bedienungsanleitung
Johnson Controls
Johnson Controls TEC3010 Bedienungsanleitung
Johnson Controls
Johnson Controls Tyco KT-1 Bedienungsanleitung
Johnson Controls
Johnson Controls CIR01 Bedienungsanleitung
Johnson Controls
Johnson Controls FX-PCV1617 Bedienungsanleitung
Johnson Controls
Johnson Controls P266 Series Bedienungsanleitung
Johnson Controls
Johnson Controls UNT110-1 Bedienungsanleitung
Johnson Controls
Johnson Controls EasyIO FW-28 Bedienungsanleitung
Johnson Controls
Johnson Controls M9316-A Z Series Bedienungsanleitung
Johnson Controls
Johnson Controls FEC1611 Bedienungsanleitung
