Johnson Controls VFD66 Series Bedienungsanleitung

Quick Start Commissioning Guide VFD66xxx-2 Series

Issue Date July 15, 2011

© 2011 Johnson Controls, Inc. 1

Part No. 24-10511-112, Rev. —www.johnsoncontrols.com

VFD66 Series Condenser Fan Speed Controls

Electrical Connections

Optional

Ground

Connection

Fuses

FIG:trmnl_cnnctns

Ground Connection

Terminals (For Power

and Motor Ground) Supply

Ground

TB2

L3/T

L2/S

L1/R

T1/U

T2/V

T3/W

Mains Supply

Figure 1: VFD66xxx-2

Power Terminal Connections

A: Alarm

B: Alarm

1: +5V Output

2: Analog Input 1

3: Analog Input 2

FIG:cntrl_cnnctns

TB1 4: 0V Common

Figure 2: VFD66xxx-2

Control Connections

Manual Operation

Operating the VFD66 Control from the Keypad

VFD66xxx-1 Setup

The speed is controlled with P1 (P2 is not used).

J2 = On, J3 = On, and J7 = On or Off.

VFD66xxx-2 Setup

Set parameter 05 to PAd (manual input mode).

Press the green button on the keyboard to run;

press the red button to stop.

Use the up arrow key to increase the speed; use

the down arrow key to decrease the speed.

Note: If you cycle the power, the VFD66xxx-2 stops

and you must press the green button again.

2VFD66 Series Condenser Fan Speed Controls Quick Start Commissioning Guide

Operating the VFD66 Control with a P35 Pressure Transducer or Any 0 to 5 VDC Signal

VFD66xxx-1 Setup

J2 = On, J3 = Off, and J7 = On.

P1 = minimum speed.

P2 = minimum speed maintain (stop or hold).

VFD66xxx-2 Setup

Set parameter 05 to Std (standard input mode;

factory default setting).

Set parameter 65 to 5V (factory default setting).

Set parameter 67 for the desired minimum speed

(factory default setting is 0 Hz).

Set parameter 64 for either stop (factory default

setting; motor stops below the minimum speed

setting) or HOLd (motor idles), to obtain the

desired action at the minimum speed point.

Operating the VFD66 Control with a C450 Control Module or Any 0 to 10 VDC Signal

VFD66xxx-1 Setup

J2 = On, J3 = Off, and J7 = Off. VFD66xxx-2 Setup

Set parameter 05 to Std (factory default setting).

Set parameter 65 to 10V.

Set parameter 67 for the desired minimum speed

(factory default setting is 0 Hz).

Set parameter 64 for either stop (factory default

setting) or HOLd, to obtain the desired action at

the minimum speed point.

Operating the VFD66 Control with a Ratiometric P499 Series Electronic Pressure Transducer

VFD66xxx-1 Setup

J2 = Off, J3 = On or Off, and J7 = On or Off.

P1 = setpoint.

P2 = proportional band.

VFD66xxx-2 Setup

Set parameter 05 to EPt (electronic pressure

transducer input mode).

Set parameter 65 to 5V (factory default setting) for

ratiometric sensors; set parameter 65 to 10V for

0 to 10 VDC sensors.

Set parameter 61 for the desired setpoint. This

setting is calculated using the following equation:

)

Max.Pressure Rating ofSensor

(

10 + 80 x Desired Pressure Setpoint

Example: If a 0 to 500 psig sensor is used and the

desired setpoint is 275 psig, then the setting for

parameter 61 is 10 + (80 x 275/500) or 54.

Set parameter 62 for the desired proportional band

of the control. This setting is calculated using the

following equation:

]

Max.Pressure Rating of Sensor

[

80 x (Pressure Setpoint – Min. Req. Pressure)

Example: If a 0 to 750 psig sensor with a setpoint

of 500 psig and a minimum required pressure of

410 psig is used, then the setting for parameter 62

is 80 x [(500 –410)/750] or 9.6.

VFD66 Series Condenser Fan Speed Controls Quick Start Commissioning Guide 3

Changing Acceleration and Deceleration Parameters on the VFD66 Control

VFD66xxx-1 Setup

If J4 = On, then the acceleration and deceleration

rate is 5 seconds (this value is in seconds/60Hz).

If J4 = Off, then the acceleration and deceleration

rate is 30 seconds (this value is in

seconds/60 Hz).

VFD66xxx-2 Setup

Set parameter 03 for acceleration

(in seconds/100 Hz). This setting is calculated

using the following equation:

60

Desired Acceleration Rate x 100

Example: A setting of 8.3 (in seconds/100 Hz)

equals a 5 second acceleration rate from

0 to 60 Hz.

Set parameter 04 for deceleration

(in seconds/100 Hz). This setting is calculated

using the following equation:

60

Desired Deceleration Rate x 100

Example: A setting of 50 (in seconds/100 Hz)

equals a 30 second deceleration rate from

0 to 60 Hz.

Note: The settings for the acceleration and

deceleration parameters are adjustable from

0 to 3,200 seconds (this range is in seconds/100 Hz).

Selecting Single or Dual Sensors (High Signal Select) on the VFD66 Control

VFD66xxx-1 Setup

If J8 = On, then dual sensors are configured with

high signal select.

If J8 = Off, then single sensor is configured.

VFD66xxx-2 Setup

Set parameter 63 to 1InP (factory default setting)

for single sensor configuration.

Set parameter 63 to 2InP for dual sensor

configuration with high signal select.

Setting the Motor Rated Frequency on the VFD66 Control

VFD66xxx-1 Setup

If J9 = On, then the motor rated frequency is

50 Hz.

If J9 = Off, then the motor rated frequency is

60 Hz.

VFD66xxx-2 Setup

Set parameter 39 to the motor rated frequency

(factory default setting is 60 Hz).

Building Efficiency

507 E. Michigan Street, Milwaukee, WI 53202

Johnson Controls/PENN® and Johnson Controls® are registered trademarks of Johnson Controls, Inc.

All other marks herein are the marks of their respective owners. © 2011 Johnson Controls, Inc.

Andere Handbücher für VFD66 Series

3

Dieses Handbuch passt für folgende Modelle

2

Andere Johnson Controls Controller Handbücher

Johnson Controls

Johnson Controls HS3032 Bedienungsanleitung

Johnson Controls

Johnson Controls M9116-GG-1N4 Series Bedienungsanleitung

Johnson Controls

Johnson Controls System 350 P352AB Series Bedienungsanleitung

Johnson Controls

Johnson Controls Tyco Kantech KT-400 Bedienungsanleitung

Johnson Controls

Johnson Controls York YKN2Open board Handbuch

Johnson Controls

Johnson Controls Joventa DMS1.1 Bedienungsanleitung

Johnson Controls

Johnson Controls tyco Power Neo HS2016 Bedienungsanleitung

Johnson Controls

Johnson Controls VA-9070 Series Service-Handbuch

Johnson Controls

Johnson Controls VA-77 Series Bedienungsanleitung

Johnson Controls

Johnson Controls FX Supervisory Controller RS-485 Card Bedienungsanleitung

Johnson Controls

Johnson Controls FX70 Bedienungsanleitung

Johnson Controls

Johnson Controls LX-HPUL-1 Bedienungsanleitung

Johnson Controls

Johnson Controls TRUE RH HC-67x3 Bedienungsanleitung

Johnson Controls

Johnson Controls CIS01 Bedienungsanleitung

Johnson Controls

Johnson Controls Metasys MS-FEU1610-0U Bedienungsanleitung

Johnson Controls

Johnson Controls VAP Series Bedienungsanleitung

Johnson Controls

Johnson Controls M9102 GA-1S Series Bedienungsanleitung

Johnson Controls

Johnson Controls CK721-A Kurzanleitung

Johnson Controls

Johnson Controls FX-PCG26 Bedienungsanleitung

Johnson Controls

Johnson Controls FX80 Bedienungsanleitung

Johnson Controls

Johnson Controls VA-7700 Series Bedienungsanleitung

Johnson Controls

Johnson Controls VA9310 Series Bedienungsanleitung

Johnson Controls

Johnson Controls TC-8902 Bedienungsanleitung

Johnson Controls

Johnson Controls P266 Series Bedienungsanleitung

Beliebte Controller Handbücher anderer Marken

Digiplex

Digiplex DGP-848 Betriebsanleitung

YASKAWA

YASKAWA SGM series Bedienungsanleitung

Sinope

Sinope Calypso RM3500ZB Bedienungsanleitung

Isimet

Isimet DLA Series Style 2 Installationshandbuch

LSIS

LSIS sv-ip5a Bedienungsanleitung

Rockwell Automation

Rockwell Automation 1769-L31 Bedienungsanleitung

Airflow

Airflow Uno hab Bedienungsanleitung

ABB

ABB ACS580-01 drives Bedienungsanleitung

Panasonic

Panasonic GM1 Series Bedienungsanleitung

Emerson

Emerson SW93 Bedienungsanleitung

AutoAqua

AutoAqua Smart ATO micro SATO-120P Bedienungsanleitung

Panasonic

Panasonic FP? Positioning Unit RTEX Bedienungsanleitung

Samson

Samson Type 5824 Service-Handbuch

Alpha IP

Alpha IP MIOB 21001 Bedienungsanleitung

Siemens

Siemens OpenAir GMA 1 Series Bedienungsanleitung

Surecom

Surecom SR-629 Bedienungsanleitung

Fishman

Fishman TriplePlay Bedienungsanleitung

Regulus

Regulus SRS1 T Bedienungsanleitung