Johnson Controls E-Link Bedienungsanleitung

E-Link Gateway Installation Instructions 1

Applications

The E-Link Gateway provides Johnson Controls® and

YORK® mechanical equipment, such as chillers and

rooftop units, with Building Automation System (BAS)

networking connectivity. It is designed with three active

serial ports: Port 1 and Port 4 are used for BAS

networking, Port 2 is reserved for connecting to the

equipment, and Port 3 provides access for auxiliary

monitoring and control.

To simplify the installation and setup, the E-Link

Gateway comes pre-configured with a series of chiller

and rooftop equipment profiles that you can choose by

selecting the correct DIP switch settings.

Several E-Link Gateway models are available for

connection to various types of input voltage and

equipment. For chillers using the OptiView™ or

Latitude Micro Panel, the E-Link Gateway consists of a

single circuit board attached to four studs inside the

Micro Panel, using the accessory mounting kit. The

panel supplies 12 VDC input power, eliminating the

need for an external power supply.

For chillers using the IPU-II based Micro Panel, the

E-Link Gateway is installed inside the Micro Panel and

requires an additional transformer to supply power to

the E-Link Gateway. The transformer is included in the

E-Link IPU-II Installation Kit. (This kit is not available in

Europe. Use E-Link Gateway YK-ELNKE00-0.)

For other types of chillers, the E-Link Gateway is

packaged in its own enclosure. In addition to the E-Link

Gateway circuit board, a transformer is included inside

the enclosure that converts a 120- or 240-volt input to

24 VAC power.

North American Emissions Compliance

United States

Canada

Installation

The E-Link Gateway is supplied as a circuit board that

can be installed directly into the equipment’s enclosure,

or can be supplied pre-mounted in an enclosure ready

for line voltage. Accessory mounting kits are used to

mount the E-link Gateway directly into OptiView

Latitude, and IPU-II based Micro Panels.

This equipment has been tested and found to

comply with the limits for a Class A digital device

pursuant to Part 15 of the FCC Rules. These limits

are designed to provide reasonable protection

against harmful interference when this equipment is

operated in a commercial environment. This

equipment generates, uses, and can radiate radio

frequency energy and, if not installed and used in

accordance with the instruction manual, may cause

harmful interference to radio communications.

Operation of this equipment in a residential area is

likely to cause harmful interference, in which case

the user will be required to correct the interference

at his/her own expense.

This Class (A) digital apparatus meets all the

requirements of the Canadian Interference-Causing

Equipment Regulations.

Cet appareil numérique de la Classe (A) respecte

toutes les exigences du Règlement sur le matériel

brouilleur du Canada.

IMPORTANT: Do not install the E-Link Gateway

directly into an equipment’s enclosure without the

use of an approved installation kit.

E-Link Gateway

Installation Instructions Part No. 24-10404-9, Rev. D

Issued November 2, 2011

Supersedes April 29, 2011

E-Link Gateway Installation Instructions2

IMPORTANT: The E-Link Gateway is intended to

provide an input to equipment under normal

operating conditions. Use this E-Link Gateway only

as an operating control. Where failure or malfunction

of the E-Link Gateway could lead to personal injury

or property damage to the controlled equipment or

other property, additional precautions must be

designed into the control system. Incorporate and

maintain other devices, such as supervisory or

alarm systems or safety or limit controls, intended to

warn of or protect against failure or malfunction of

the E-Link Gateway.

Table 1: YORK Chiller Models (Current

Production)

Board

Number1Language

(Native) Chiller Model

031-02550 BACnet®,

Modbus®,

YORK Talk 2,

4,800 bits per

second (bps)

YCWL, YCUL, YCAL,

YLAA, YCRL, YLPA

031-01095 YORK Talk 2,

4,800 bps YCAS, YCWS, YCRS

031-02478 YORK Talk 2,

4,800 bps YCAV, YCIV, YVAA

031-01065 YORK Talk 2,

1,200 bps YIA, YPC, YG, YB

031-01730 YORK Talk 3 YN, OM RETROFITS,

031-02430 YORK Talk 3 YK, YT, YS, YR, YST,

YD, YMC2

331-02496 BACnet® YPAL

YORK-003 Modbus RTU YEWS-D1, YEAS,

YGAS2

1. Installing technician must verify board number in unit

prior to installation.

2. Software edition of YEWS-D1 (RHSYEWSD1) V1.08 or

later), YEAS (RHMASB V1.06 or later), YGAS

(RHMYGAS V1.03 or later) are supported.

Table 2: E-Link Gateway Product Code Numbers

Description Product Code

Numbers

E-Link with Serial Outputs (BACnet

Master-Slave/Token-Passing [MS/TP],

Modbus Remote Terminal Unit [RTU],

and N2)

YK-ELNK100-0

E-Link with LONWORKS® as an Output YK-ELNK101-0

E-Link with Serial Outputs in

Enclosure YK-ELNKE00-0

E-Link with LONWORKS Output in

Enclosure YK-ELNKE01-0

E-Link OptiView/Latitude Panel

Installation Kit YK-ELNKOLK-0

E-Link IPU-II Panel Installation Kit

(not available in Europe) YK-ELNKSTK-0

E-Link Gateway Installation Instructions 3

Mounting

OptiView Panel Installation

1. Attach the E-Link Gateway board to the studs

provided inside the chiller enclosure (Figure 1 or

Figure 2), using the four screws and washers

provided in the OptiView/Latitude installation kit.

2. Connect the communications cable (included with

the kit) from Port 2B on the E-Link Gateway to J2

on the OptiView Micro Panel. Ensure that wires are

connected according to Table 3.

3. Check for stray wire strands, which could cause

short circuits, and ensure all components are

secure.

4. Connect the BAS network to Port 1 (if the protocols

are transported by RS-485) or Port 4 (if the BAS

network is LONWORKS).

Note: For RS-485 2-wire operation, connect a 100

ohm 1 W resistor between COM and the E-Link

Gateway’s TB5 COM (see Figure 24).

5. Ensure jumper JP27 is set for RS-232 (see

Figure 20).

6. Connect the power harness (included with the kit)

from J2 on the E-Link Gateway to J21 on the

Optiview Micro Panel (see Figure 20).

The E-Link Gateway is now ready to be configured

using Quick Start; see the Commissioning a Standard

Application section in this document.

WARNING: Risk of Electric Shock.

Disconnect or isolate all power supplies

before making electrical connections.

More than one disconnect or isolation

may be required to completely de-

energize equipment. Contact with

components carrying hazardous voltage

can cause electric shock and may result

in severe personal injury or death.

Table 3: OptiView Wiring - E-Link Port 2B

E-Link Port 2B OptiView Port Wire Color

RX GTX Black

TX GRX Red

REF N/A Shield/Drain

Table 4: BAS Wiring - E-Link Port 1

E-Link Port 1 BAS Wire Color

++White

--Blue

REF REF Black

FIG:Opti_Pnl

Figure 1: OptiView Micro Panel Connected to

E-Link Gateway

FIG:Opti_Pnl1

Figure 2: OptiView Micro Panel for YMC2

Connected to E-Link Gateway

E-Link Gateway Installation Instructions4

IPU-II Panel Installation

(Installation Kit Not Available in Europe)

1. Attach the E-Link Gateway board to the panel in

the upper right side of the enclosure using the four

expansion screws and nuts provided in the IPU-II

Panel Installation Kit (see Figure 3).

2. Attach the 24 VAC transformer to the panel to the

left of the E-Link board using two screws (see

Figure 3).

3. Connect the communications cable (included with

the kit) between the E-Link board and IPU-II Micro

board.

4. Connect the transformer to the terminal block.

5. Connect the transformer to E-Link. Secure the

wiring with tie-wraps.

6. Connect the resistor if the RS-485 2-wire operation

is required.

7. Connect the communications cable shielded

ground to the ground screw.

The E-Link Gateway is now ready to be configured

using Quick Start; see the Commissioning a Standard

Application section in this document.

Micro Boar

24 VAC

Transforme

Expansion

Nut

Expansion

Nut

Screw

Sheet

Metal

Screw

Resisto

Secondar

Powe

Wiring

Harness Tie

Wrap

TB 2

E-LIN

Transforme

Secondar

Ground

Communication

Wiring Harness

Com

Ground

T B1

T B 5

The Resistor is used for BAS

RS485 2 Wire Connection.

Connect one end of the

Resistor to the COM o

TB5 (24 VAC) and the othe

to Port 1 COM.

Use this resistor only if the

BAS wiring utilizes a 2 Wire

communication trunk

Communication Wiring Harness:

Connect to Micro Board

TB1 as Follows:

Wire Color / Terminal

Red / +

Black / -

REFSHLD

TB 1 RS485

Terminal block location

for YCAL-D, YCAL-E, and YLAA.

Terminal block location

for YCAL-C, YCWL, and

Primary Powe

Wiring Harness

TB2

TB5

CUL-C.

Figure 3: IPU-II Panel Installation (Installation Kit Not Available in Europe)

E-Link Gateway Installation Instructions 5

Other Chiller Panel Installation

For all other applications, the E-Link Gateway includes

an optional enclosure. The optional enclosure does not

include communication cables due to the variety of

types and lengths that may be required.

The E-Link Gateway can be mounted as a stand-alone

enclosure either on the outside surface of the chiller

Micro Panel (close coupled), or on a smooth surface

within close proximity of the chiller panel enclosure.

For mounting on a Micro Panel, the line voltage power

is supplied by a power source in the Micro Panel.

Mounting on a Micro Panel

To mount the E-Link Gateway on a Micro Panel:

1. Disconnect power to the chiller Micro Panel.

2. Make sure the E-link Gateway enclosure fits

properly and that no obstructions, such as internal

boards, switches, or external conduit, prevent

mounting or servicing of the panel. See Figure 4 for

examples of good mounting locations.

3. Locate and remove the two plastic caps in the

bottom of the E-Link Gateway enclosure.

4. Mark an appropriate place on the enclosure for a

matching set of knock out holes. Mark and drill, or

punch, two holes in the Micro Panel.

5. Using two bulkhead pipe couplers, attach the

E-Link Gateway enclosure to the Micro Panel.

6. Complete wiring as described in the Applying

Power section in this document.

Note: Use of bulkhead pipe couplers provides

sufficient clearance to allow removal of the E-Link

Gateway cover.

IMPORTANT: Never install the E-Link Gateway

outside the confines of a building unless within

another enclosure rated IP 65/NEMA 4x or higher.

IMPORTANT: Make sure that the cover is securely

fastened to the enclosure and the internal ground

wire is attached before placing the Gateway in

operation. These steps help to minimize Radio

Frequency Interference (RFI) from being generated

and picked up.

WARNING: Risk of Electric Shock.

Disconnect or isolate all power supplies

before making electrical connections.

More than one disconnect or isolation

may be required to completely

de-energize equipment. Contact with

components carrying hazardous voltage

can cause electric shock and may result

in severe personal injury or death.

IMPORTANT: When attaching the E-Link Gateway

to a Micro Panel, ensure the E-Link Gateway does

not impede access to other components.

IMPORTANT: Be careful not to damage the E-link

Gateway or Micro Panel’s circuit boards during the

installation. Protect all circuit boards from metal

chips, which may cause short circuits if left on the

boards at startup.

E-LINK

Enclosure

YORK Chiller

Micro Panel

Alternative

Mounting

Locations

FIG:MntEquip

Figure 4: Mounting on the Equipment

E-Link Gateway Installation Instructions6

Wall Mounting

To mount the E-Link Gateway on a wall:

1. Check for proper clearances for the necessary

electrical and communications cable runs.

2. Ensure that power and communications wiring is in

compliance with all local, national, and regional

codes, and customer requirements.

3. Select a suitable location and mark the anchor

points. Ensure that the enclosure is level. See

Figure 5 for an example.

4. Drill the appropriate holes in accordance with the

type of wall anchor used.

5. Install the enclosure on the wall.

6. Check that the mounting is secure and the wiring

connections are correct and tight. Check that no

loose wire strands or other metal objects that could

cause a short circuit are on the circuit board.

7. Complete wiring as described in the Applying

Power section.

Applying Power

When using an enclosure type of E-Link Gateway,

power can be supplied from either a separate power

supply or the main terminal strip in the chiller panel.

Locate the power source within 0.9 m (3 ft) of the

E-Link Gateway, and protect it with a suitable fuse or

circuit breaker. Ensure the power is supplied from a

dedicated source and not controlled by a programmed

switch.

If the enclosure is mounted on a wall, the wiring from

the power source to the E-Link Gateway must always

run in a suitable conduit. To obtain the best

Electromagnetic Interference (EMI) and

Electromagnetic Compatibility (EMC) performance,

ensure that the conduit is bonded to the metal of both

enclosures. Scraping the paint around the knockouts

usually helps provide a better electrical connection

between the joining parts.

1. Connect a 1.29-1.02 mm (16-18 AWG) wire from a

reliable ground reference to the E-Link Gateway’s

incoming power ground lug. Do not remove the

existing wire that connects the ground lug to the

enclosure cover.

2. On 120 VAC applications, connect the Hot wire to

TB2 and the Neutral wire to TB1. Connect the

ground wire to a ground lug.

On 240 VAC applications, connect the Hot wire to

TB3 and the Neutral wire to TB1. Connect the

ground wire to a ground lug.

IMPORTANT: When wall mounting, make sure

there is no interferencewith other components in the

near vicinity. Use appropriate conduit to connect the

power and communications wiring.

IMPORTANT: Be careful not to damage the circuit

boards during installation.

YORK Chiller

Micro Panel

Template for Mounting

on a Wall

Conduit

E-Link

Enclosure

FIG:WllMnt

Figure 5: Wall Mounting

WARNING: Risk of Electric Shock.

Disconnect or isolate all power supplies

before making electrical connections.

More than one disconnect or isolation

may be required to completely

de-energize equipment. Contact with

components carrying hazardous voltage

can cause electric shock and may result

in severe personal injury or death.

CAUTION: Risk of Property Damage.

Do not apply power to the system before

checking all wiring connections. Short

circuited or improperly connected wires

may result in permanent damage to the

equipment.

IMPORTANT: Use copper conductors only.

Make all wiring connections in accordance with

local, national, and regional regulations. Do not

exceed the E-Link Gateway’s electrical ratings.

E-Link Gateway Installation Instructions 7

Commissioning a Standard Application

Once the E-Link Gateway has been mechanically and

electrically installed (that is, it has been located in its

enclosure, wired, and terminated appropriately), it may

be Quick Commissioned.

1. Apply power and verify that the red power

Light-Emitting Diode (LED) on the IPU-II board is

on. Make sure the T-switch is set to OFF, and then

set the required Media Access Control (MAC)

address. Set the MAC address in accordance with

the system integrator to ensure that a unique

address is used. If any non-standard setup is

required, refer to the E-Link Commissioning and

Troubleshooting Guide (LIT-12011238) for more

details.

2. Based on the equipment to be integrated (see

Table 8) and the required BAS output protocol (see

Table 9), select the appropriate settings on

GROUP A and GROUP B switches. For equipment

points lists, refer to the Johnson Controls Portal

(Products and Services>Delivery>Products/

Service Field Support>Equipment

Integration>YORK Equipment Data Maps).

3. Press, hold a few seconds, then release the push

button shown in Figure 11. The status LED flashes

quickly. After the E-Link Gateway re-initializes, the

commissioning is complete.

4. When commissioning a LONWORKS BAS output

protocol, disconnect the BAS network and cycle

the power on the E-Link Gateway to activate the

Quick Start and the LONWORKS FTT10 ProtoCessor.

The ProtoCessor does not recognize the push

button as a trigger to reset and load the correct

conversion file. Wait a minimum of 10 minutes

before reconnecting the BAS network.

5. Check the E-Link Gateway’s LEDs. First, check the

STATUS LED; if the E-Link Gateway has no errors,

it flashes continuously (1/2 second on, 1/2 second

off). If the LED is not flashing continuously, see

Table 6 for possible reasons.

FIG:PwrConn

Figure 6: Power Connection Shown as 120 VAC

Table 5: Allowable MAC Addresses

Protocol Max Allowable Switch

Settable MAC

Addresses

BACnet MS/TP 1 – 127

N2 1 – 127

Modbus RTU 1 – 127

E-Link Gateway Installation Instructions8

6. Place the equipment in remote operating mode to

accept commands from the E-Link Gateway. Refer

to the equipment installation literature for the

proper configuration settings.

For all chillers that use the YORK Talk protocols, check

that the Port 2 communication LEDs, Red (TX) and

Green (RX), are flashing. This scenario indicates that

the chiller panel is being polled and is responding. See

Figure for the location of Port 2 communication LEDs.

What You Should Know before

Using Quick Starts

The E-Link is designed to use a set of predefined data

maps to associate equipment data with a set of fixed

BAS network variables. You are not able to make any

field changes to these data maps; attempting to do so

results in the automatic reversal of any edits that you

may have made. For any field patches, refer to your

local FSC (Field Support Center) for guidance.

The data maps used by the E-Link Gateway are based

on a collection of version controlled equipment point

lists, which are supplied by the equipment business for

the purpose of integrating equipment into BAS

networks. Unless noted otherwise, the equipment’s

data is available in these supported BAS protocols:

BACnet MS/TP, N2, LONWORKS, and Modbus RTU.

The first release of the E-Link was positioned to

provide the equivalent functionality as offered by the

YORK MicroGateway. That release requires you to

reference point lists which are version J or earlier. All

subsequent E-link releases use point lists version K or

later.

Quick Starts 1 through 16 all use the J version point

lists, whereas Quick Starts 17 through 33 use the K

version. The primary difference between the two

categories is that Quick Starts 1 through 16 have

limited network visible points. In this case, the available

points are those which were originally available at the

time when the MicroGateway was first released.

Quick Starts 17 and higher offer a much richer

equipment point compliment that is more reflective of

what the equipment currently makes available today.

These Quick Starts also create profiles that use more

descriptive BACnet point names, use engineering

units, and follow the BACnet Testing Laboratories™

(BTL) guidelines for compliance as a B-ASC controller.

In most cases, using a Quick Start that corresponds to

the equipment being integrated is sufficient to configure

the E-Link Gateway for operating on the BAS network;

however, in some circumstances, you will be required

to provide further customizing by connecting a laptop

computer onto Port 3 and then accessing the User

Reports (refer to the E-Link Gateway Commissioning

and Troubleshooting Technical Bulletin [LIT-12011238]

for more information).

Table 6: LED Status indication

Flash Rate Status LED Indication

LED Off No database configuration is loaded, or no

input power is present.

1 Flash Terminal mode has been invoked (Switch

T is on).

2 Flashes An equipment to E-Link communications

error has occurred.

3 Flashes A Quick Start has a configuration error.

LED On No errors with custom/field modified

application.

Flashing

Continuously No errors with factory standard

application.

Table 7: E-Link Releases

Firmware/Database Revision Point Lists

SSM4567 JCF0003BL.BIN J and earlier only

SSM4567 JCF0008BL.BIN J and earlier, or K

E-Link Gateway Installation Instructions 9

Table 8: Equipment Quick Start Selections

APP Group Switch A Equipment Profile Quick Starts

SwitchSettings 32168421Functionality

110 0 0 0 0 1 YK with SSS Imperial (YORK Talk-III) J version points

2 0 0 0 0 1 0 YK with VSD Imperial (YORK Talk-III) J version points

310 0 0 0 1 1 YT with SSS Imperial (YORK Talk-III) J version points

4 0 0 0 1 0 0 YT with VSD Imperial (YORK Talk-III) J version points

510 0 0 1 0 1 YS / YR with SSS Imperial (YORK Talk-III) J version points

610 0 0 1 1 0 YK with SSS Metric (YORK Talk-III) J version points

7 0 0 0 1 1 1 YK with VSD Metric (YORK Talk-III) J version points

810 0 1 0 0 0 YT with SSS Metric (YORK Talk-III) J version points

9 0 0 1 0 0 1 YT with VSD Metric (YORK Talk-III) J version points

1010 0 1 0 1 0 YS / YR with SSS Metric (YORK Talk-III) J version points

11 0 0 1 0 1 1 YORK Talk II, 1200, 1 Section (YORK Talk-II) J version points

12 0 0 1 1 0 0 YORK Talk II, 4800, 1 Section (YORK Talk-II) J version points

1320 0 1 1 0 1 YORK Talk II, 4800, 2 Sections (YORK Talk-II) J version points

14 0 0 1 1 1 0 YD Imperial (YORK Talk-III) J version points

15 0 0 1 1 1 1 YD Metric (YORK Talk-III) J version points

16 0 1 0 0 0 0 ECO2 / YPAL / S100 (BACnet MS/TP via an IPU-I)

17 0 1 0 0 0 1 YK with SSS Imperial (YORK Talk-III) K version points

18 0 1 0 0 1 0 YK with VSD Imperial (YORK Talk-III) K version points

19 0 1 0 0 1 1 YT with SSS Imperial (YORK Talk-III) K version points

20 0 1 0 1 0 0 YT with VSD Imperial (YORK Talk-III) K version points

21 0 1 0 1 0 1 YS / YR with SSS Imperial (YORK Talk-III) K version points

22 0 1 0 1 1 0 YK with SSS Metric (YORK Talk-III) K version points

23 0 1 0 1 1 1 YK with VSD Metric (YORK Talk-III) K version points

24 0 1 1 0 0 0 YT with SSS Metric (YORK Talk-III) K version points

25 0 1 1 0 0 1 YT with VSD Metric (YORK Talk-III) K version points

26 0 1 1 0 1 0 YS / YR with SSS Metric (YORK Talk-III) K version points

27 0 1 1 0 1 1 YST Imperial (YORK Talk-III) K version points

28 0 1 1 1 0 0 YIA Imperial (YORK Talk-III) K version points

29 0 1 1 1 0 1 YST Metric (YORK Talk-III) K version points

30 0 1 1 1 1 0 YIA Metric (YORK Talk-III) K version points

31 0 1 1 1 1 1 YEWS-D1/YEAS/YGAS (Modbus native)

32 1 0 0 0 0 0 YD Imperial (YORK Talk-III) K version points

33 1 0 0 0 0 1 YD Metric (YORK Talk-III) K version points

34 1 0 0 0 1 0 YMC2 Imperial (YORK Talk-III) K version points

35 1 0 0 0 1 1 YMC2 Metric (YORK Talk-III) K version points

63 1 1 1 1 1 1 Reserved for Field adjustments

1. A Quick Start that references a Solid State Starter (SSS) is also applicable to a mechanical starter.

2. Two sections are required for equipment equipped with three or more compressors, or two systems.

E-Link Gateway Installation Instructions10

Table 9: BAS Output Protocol Quick Start Selections

APP Group

Switch B Output Protocol Quick Starts

SwitchSettings 8421Port1 Port3 Port4

0 1

1. When making edits to User Report 4 (Port Configuration), Group Application Switch B must be set to zero. This setting

ensures that the edits are stored. Otherwise, the edits are overwritten to the default values assigned to the particular Group

Switch B setting the next time E-Link is reset, or power is cycled. Edits made in any other User Reports do not require

alterations to either bank of Group Application switches. For standard set-up, not requiring modifications via User Report 4,

use application switch B, settings 1 to 14.

0000MS/TP,AUTO,N,8,1 Modbus,19,200,N,8,1 Terminal

1 2, 5

2. The Terminal setting on Port 4 is restricted for factory use only.

To comply with the LONMARK® specification, all data transmitted on the LONWORKS network must be expressed in SI units

(metric units). The LONWORKS ProtoCessor performs no unit conversions; it assumes that the data supplied is already

correctly expressed.

0001MS/TP,AUTO,N,8,1 Modbus,19,200,N,8,1 Terminal

2 2, 5 0010MS/TP,AUTO,N,8,1 Modbus,19,200,N,8,2 Terminal

3 2, 5 0011MS/TP,AUTO,N,8,1 N2,9,600,N,8,1 Terminal

4 2, 5 0100N2,9,600,N,8,1 MS/TP,38,400,N,8,1 Terminal

5 2, 5 0101Modbus, 19,200, N, 8, 1 MS/TP, 38,400, N, 8, 1 Terminal

6 2, 5 0110Modbus, 19,200, N, 8, 2 MS/TP, 38,400, N, 8, 1 Terminal

7 2, 5 0111Modbus, 9,600, E, 8, 1 MS/TP, 38,400, N, 8, 1 Terminal

8 2, 5 1000Modbus, 9,600, N, 8, 1 MS/TP, 38,400, N, 8, 1 Terminal

93, 5, 6

3. Use Quick Start 9 and 11 if the equipment is supplying the data in SI units (the E-Link is not required to perform any

conversions, so it operates in pass-through mode).

1001N2,9,600,N,8,1 Modbus,19,200,N,8,1 L

ONWORKS – Pass through

10 4, 5, 6

4. Use Quick Start 10 and 12 if the equipment is supplying the data in Imperial units and the E-Link is required to convert these

units into SI.

5. Setting Switch T = ON, on the MAC address, forces TERMINAL mode of Port 3, at 57,600 baud, N, 8, 1. This setting is only

required to debug the E-Link Gateway’s operation, or access the User Reports.

6. Select Quick Starts 9 and 10 when connecting the E-Link Gateway to an ECO2 unit.

1010N2,9,600,N,8,1 Modbus,19,200,N,8,1 L

ONWORKS – Conversion

11 3, 5 1011Modbus, 19,200, N, 8, 2 N2, 9,600, N, 8, 1 LONWORKS – Pass through

12 4, 5 1100Modbus, 19,200, N, 8, 2 N2, 9,600, N, 8, 1 LONWORKS – Conversion

13 2, 5 1101Modbus, 9,600, E, 8, 1 Modbus, 19,200, N, 8, 2 Terminal

14 2, 5 1110MS/TP,38,400,N,8,1 N2,9,600,N,8,1 Terminal

15 7

7. Quick Starts 15 on APP Group B, and 63 on APP Group A, are reserved for field adjustments.

1111Reserved Reserved Terminal

Inhaltsverzeichnis

Andere Johnson Controls Tor Handbücher

Johnson Controls

Johnson Controls WNC1800 Bedienungsanleitung

Johnson Controls

Johnson Controls VRF Smart Gateway Bedienungsanleitung

Johnson Controls

Johnson Controls WT-BAC-IP Bedienungsanleitung

Johnson Controls

Johnson Controls MAP 1810 Bedienungsanleitung

Johnson Controls

Johnson Controls YK-MAP1810-0E Bedienungsanleitung

Johnson Controls

Johnson Controls TL-MAP1810-OP Bedienungsanleitung

Johnson Controls

Johnson Controls Simplicity LINC Benutzerhandbuch

Johnson Controls

Johnson Controls MAP 1850 Bedienungsanleitung

Johnson Controls

Johnson Controls TL-MAP1810-OP Bedienungsanleitung

Johnson Controls

Johnson Controls MAP Bedienungsanleitung

Johnson Controls

Johnson Controls 24-10737-8 Bedienungsanleitung

Johnson Controls

Johnson Controls MAP 1810 Bedienungsanleitung

Johnson Controls

Johnson Controls MAP Series Bedienungsanleitung

Johnson Controls

Johnson Controls WNC1800 Bedienungsanleitung

Johnson Controls

Johnson Controls York Smart Equipment SC-EQUIP Bedienungsanleitung

Johnson Controls

Johnson Controls WNC1800 Bedienungsanleitung

Beliebte Tor Handbücher anderer Marken

LST

LST M500RFE-AS Bedienungsanleitung

Kinnex

Kinnex Media Gateway Bedienungsanleitung

2N Telekomunikace

2N Telekomunikace 2N StarGate Bedienungsanleitung

Mitsubishi Heavy Industries

Mitsubishi Heavy Industries Superlink SC-WBGW256 Bedienungsanleitung

ZyXEL Communications

ZyXEL Communications ZYWALL2 ET 2WE Bedienungsanleitung

Telsey

Telsey CPVA 500 - SIP Bedienungsanleitung

RTA

RTA 460A-NNA4 Technisches Datenblatt

Shaw

Shaw Gateway HDPVR Bedienungsanleitung

ABB

ABB VSN900 Kurzanleitung

Commander

Commander Pulse Bedienungsanleitung

2N Telekomunikace

2N Telekomunikace ATEUS EasyGate 501309E Bedienungsanleitung

NETGEAR

NETGEAR C6300BD Bedienungsanleitung

Amit

Amit CDW531AM Bedienungsanleitung

HMS

HMS Netbiter EasyConnect EC150 Bedienungsanleitung

Huawei

Huawei EchoLife HG620 Bedienungsanleitung

AT&T

AT&T U-verse 3801 Gebrauchs- und Pflegehandbuch

Logic IO

Logic IO RTCU MX2 turbo Bedienungsanleitung

Suttle

Suttle MediaMAX MXM-521 Bedienungsanleitung