Joy-it BUMP-SENSOR Bedienungsanleitung

Joy-IT powered by SIMAC Electronics GmbH - Pascalstr. 8 - 47506 Neukirchen-Vluyn - www.joy-it.net

BUMP-SENSOR

SEN-BUMP01

BUMP-SENSOR

SEN-BUMP01

1. GENERAL INFORMATION

Dear customer,

thank you very much for choosing our product.

In the following, we will introduce you to what to observe while starting

up and using this product.

Should you encounter any unexpected problems during use, please do

not hesitate to contact us.

2. DEVICE OVERVIEW

When the switch is not activated, a HIGH level is present at the signal pin.

When the switch is activated, a LOW level is present at the signal pin and

the LED on the board lights up red.

PowerSupply -

PowerSupply +

Signal

3. USE WITH ARDUINO

Wiring

Connect the sensor to your Arduino as shown in the diagram and table

below.

BUMP-Sensor Arduino

GND GND

VCC 5 V

OUT 2

Example Code

In this code example, the status of the sensor is read out every second

and displayed in the serial monitor.

const int SWITCH_PIN = 2;

bool switchState = HIGH; //Variable the switch status

void setup() {

// Initialize the switch pin as an input

pinMode(SWITCH_PIN, INPUT);

// Initialize serial communication at 9600 bps:

Serial.begin(9600);

}

void loop() {

// Read the state of the switch value:

switchState = digitalRead(SWITCH_PIN);

// Read the state of the switch

if (switchState == LOW) {

Serial.println("Switch is pressed!");

} else {

Serial.println("Switch is not pressed!");

}

// Wait for a short period before reading again

delay(1000);

}

4. USE WITH RASPBERRY PI

Wiring

Connect the sensor to your Raspberry Pi as shown in the diagram and

table below.

BUMP-Sensor Raspberry Pi

GND GND (Pin 6)

VCC 3V3 (Pin 1)

OUT GPIO17 (Pin 11)

Example Code

In this code example, the status of the sensor is read out every second

and displayed in the console.

import RPi.GPIO as GPIO

import time

# Define the GPIO pin number

SWITCH_PIN =17

# Setup GPIO mode

GPIO.setmode(GPIO.BCM)

# Setup the GPIO pin as input with a pull-up resistor

GPIO.setup(SWITCH_PIN, GPIO.IN, pull_up_down=GPIO.PUD_UP)

try:

while True:

# Read the state of the switch

switch_state =GPIO.input(SWITCH_PIN)

# Check switch state

if switch_state == 0:

print("Switch is pressed!")

else:

print("Switch is not pressed!")

# Wait for a short period before reading again

time.sleep(1)

except KeyboardInterrupt:

# Cleanup the GPIO settings when the script is terminated

GPIO.cleanup()

Published: 20.09.2023

www.joy-it.net

SIMAC Electronics GmbH

Pascalstr. 8, 47506 Neukirchen-Vluyn

5. ADDITIONAL INFORMATION

Our information and take-back obligations according to the Electrical and

Electronic Equipment Act (ElektroG)

Symbol on electrical and electronic equipment:

This crossed-out dustbin means that electrical and electronic appliances do not

belong in the household waste. You must return the old appliances to a

collection point.

Before handing over waste batteries and accumulators that are not

enclosed by waste equipment must be separated from it.

Return options:

As an end user, you can return your old device (which essentially fulfills the same

function as the new device purchased from us) free of charge for disposal when

you purchase a new device.

Small appliances with no external dimensions greater than 25 cm can be dis-

posed of in normal household quantities independently of the

purchase of a new appliance.

Possibility of return at our company location during opening hours:

SIMAC Electronics GmbH, Pascalstr. 8, D-47506 Neukirchen-Vluyn,

Germany

Possibility of return in your area:

We will send you a parcel stamp with which you can return the device to us free

of charge. Please contact us by email at Service@joy-it.net or by telephone.

Information on packaging:

If you do not have suitable packaging material or do not wish to use your own,

please contact us and we will send you suitable packaging.

6. SUPPORT

If there are still any issues pending or problems arising aer your purcha-

se, we will support you by e-mail, telephone and with our ticket support

system.

Email: service@joy-it.net

Ticket system: http://support.joy-it.net

Telephone: +49 (0)2845 9360-50 (Mon - Thur: 10:00 - 17:00 o‘clock,

Fri: 10:00 - 14:30 o‘clock)

For further information please visit our website:

www.joy-it.net

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Joy-it Sicherheitssensor Handbücher

Joy-it

Joy-it JT-RAD01 Bedienungsanleitung

Beliebte Sicherheitssensor Handbücher anderer Marken

THORLABS

THORLABS PDA10JT Bedienungsanleitung

Waeco

Waeco UV-DETECT Bedienungsanleitung

Intermatic

Intermatic IOS-DSIMF Bedienungsanleitung

urmet domus

urmet domus 1083 Bedienungsanleitung

Siemens

Siemens AZL66 Series Bedienungsanleitung

BTI

BTI Profiline Multi Finder Bedienungsanleitung

Challenger

Challenger SL01 Bedienungsanleitung

DMP Electronics

DMP Electronics 1122INT Bedienungsanleitung

Rielta

Rielta Ladoga MK-RK Bedienungsanleitung

Mirion Technologies

Mirion Technologies ACCURAD PRD Bedienungsanleitung

Bosch

Bosch DS835 Bedienungsanleitung

DBI SALA

DBI SALA EZ Stop Bedienerhandbuch

Lamptime

Lamptime ST05C Bedienungsanleitung

Ubiquiti

Ubiquiti MFI-MSC Bedienungsanleitung

Subsite

Subsite 910R Montageanleitung

Satel

Satel OPAL Pro Bedienungsanleitung

Aleph

Aleph XC-1XTEU Bedienungsanleitung

Pima

Pima LARIS QUAD Bedienungsanleitung