JRC NSVS1234 Bedienungsanleitung

NSVS1234 Oct. 2008

Application

174MHz (BW=22MHz) for GPS-IF

Electrical Specification: (Table 1)

The device characteristics are measured in the circuit shown in Fig.1.

Maximum Rating: (Table 2)

Mechanical Specification: (Fig.2)

Package is designed as small as 5.2x4.5x1.5[mm3] for SMD (Surface Mount Device) type.

Notice:

This part is electrostatic discharge sensitive and may be damaged by improper handling.

Communications Equipment Division

Communications Equipment Marketing Department

10-1, Nishi-Shinjuku 6-chome, Shinjuku-ku,

Tokyo, 160-8328 Japan

Tel. +81 3-3348-3845

Fax. +81 3-3348-3935

http://www.jrc.co.jp/jp/product/device/saw/index.html (Japanese)

http://www.jrc.co.jp/eng/product/saw/index.html(English)

Table 1. Electrical Specifications

Parameter Spec. Typ.

Input and Output Impedance - 50Ω

Nominal Center Frequency (f0) - 174MHz

Insertion Loss 12.0dB max. 10.8dB

Passband Ripple 1.5dB max. 0.9dB

Group Delay Variation 163~185MHz 100ns max. 40ns

124~154MHz 30dB min. 38dBOut of Band Rejection

(Relative to minimum Insertion Loss) 194~224MHz 18dB min. 28dB

(Operating Temperature Range: -40~+85ºC)

Table 2. Maximum Ratings

Parameter Rating

Maximum Input Power +10dBm

Maximum DC Voltage 7.5V

Operating Temperature Range -40~+85ºC

Storage Temperature -40~+85ºC

JRC SAW FILTER

NSVS1234

NSVS1234 Oct. 2008

1.27

1.0

5.3

1.6

1.0

6.0

Via-Hole(

0.3)

[6x]

[3x]

Marking

(1) Manufacture’s Mark

(2) Lot Number

(a) Year

(b) Month

*Oct.--- X

Nov.--- Y

Dec.--- Z

1-9 --- 0

10-19--- 1

20-31--- 2

(3) Part number Mark

Pin no. Connection

1 GND

2 IN

3 GND

4 GND

5 GND

6 OUT

7 GND

8 GND

Fig.1 Measuring Circuit

Fig.2 Package dimensions (in mm)

Fig.3 Desirable land area (in mm)

50Ω∗OUT

50Ω∗

SAW

*murata LQW18A series

5.2±0.2

4.5±0.2

1.5±0.2

(0.7)

(4-R0.2)

8(12-R0.3)

(1.2)(1.55)

(1.27)(1.27)

(0.75)

(0.8)

J8X1

083

(1) (a) (b)

(2)

(3)

[8x]

(1.27)(1.27)

[2x]

[5x]

(C)

NSVS1234 Oct. 2008

Notice

1. Use this component within operating temperature range. It might not be

satisfied with electrical specification without operating temperature range.

When it is used less than -40ºC or more than +85ºC, it might be a cause of

degradation or destruction of the component. Even if it endures during a short

time, it causes degradation of qualification.

2. When soldering iron is used, solder with the temperature at the tip of soldering

iron: 350ºC max., the time of soldering: 10 seconds max., the power of

soldering iron: 30W max..

3. Notice that the allowed time of soldering with soldering iron is accumulated

time, when soldering is repeated.

4. As rapid temperature change for cleaning after reflow soldering might be a

cause of destruction clean this component after confirming that temperature of

this component goes down to room temperature.

5. Confirm that there are not any influence for qualification to this component in

mounting on PCB when this component is cleaned.

6. As it might be a cause of degradation of destruction to apply static electricity to

this component, do not apply static electricity or excessive voltage while

assembling and measuring. And do not transport this component with bare

hand.

7. As it might be a cause of degradation or destruction to apply D.C. voltage

between each terminal, apply D.C. voltage 7.5V max. in actual circuit.

Note

1. This specification specifies the quality of this component as a single unit. Make

sure that this component is evaluated and confirmed against this specification

when it is mounted to your products.

2. The information contained herein may be changed without prior notice. It is

therefore advisable to contact Japan Radio Company before proceeding with the

design of equipment incorporating this product.

3.The products are designed to be used with ordinary electronic equipment (data

and communications equipment, office equipment, audio-video equipment,

measuring instruments, etc). Japan Radio Company does not assume any

liability for the case using the products with the application required high

reliability or safety extremely (such as space equipment, sea-bottom equipment,

medical equipment etc). When intending to use any our product please

contact our sales representatives in advance.

NSVS1234 Oct. 2008

FREQUENCY CHARACTERISTICS

S22

S11

134 154 174 194 214

Frequency [MHz]

Insertion Loss [dB]

154 164 174 184 194

200

300

400

500

600

700

Frequency [MHz]

Group Delay [ns]

Inhaltsverzeichnis

Andere JRC Wasserfiltersystem Handbücher

Beliebte Wasserfiltersystem Handbücher anderer Marken

Wisy

Wisy LineAir 100 Bedienungsanleitung

Schaffner

Schaffner Ecosine FN3446 Series Betriebsanleitung

Pentair

Pentair FLECK 4600 SXT Benutzerhandbuch

H2O International

H2O International H20-500 Bedienungsanleitung

Renkforce

Renkforce 2306241 Bedienungsanleitung

Neo-Pure

Neo-Pure TL3-A502 Bedienungsanleitung

FLTR

FLTR OBF Bedienungsanleitung

STA-RITE

STA-RITE VERTICAL GRID DE FILTERS S7D75 Bedienungsanleitung

Applied Membranes

Applied Membranes W-G844EM Bedienungsanleitung

BEGA

BEGA 116 Bedienungsanleitung

WATA

WATA Standard Bedienungsanleitung

Price

Price FFU series Handbuch

Gaggenau

Gaggenau BRITA INTENZA 467873 Bedienungsanleitung

Brita

Brita SAFF-100 Bedienungsanleitung

HEISSNER

HEISSNER FPU24000-00 Bedienungsanleitung

BGS technic

BGS technic 1518 Bedienungsanleitung

Reverse Osmosis

Reverse Osmosis RF Series Bedienungsanleitung

ubbink

ubbink Filtramax Series Bedienungsanleitung