Jung 2302.16 REG HM Bedienungsanleitung
Switch actuator
Switch actuator, 2-gang
Art. No. 2302.16 REG HM
Switch actuator, 4-gang
Art. No. 2304.16 REG HM
Switch actuator, 8-gang
Art. No. 2308.16 REG HM
Switch actuator, 4-gang, C-load
Art. No. 2304.16 REG C HM
Switch actuator, 8-gang, C-load
Art. No. 2308.16 REG C HM
Operating instructions
1 Safety instructions
Electrical equipment may only be installed and fitted by electrically skilled persons.
Failure to observe the instructions may cause damage to the device and result in fire and
other hazards.
Danger of electric shock. Device is not suitable for disconnection from supply voltage.
Danger of electric shock on the SELV/PELV installation. Do not connect loads for mains
voltage and SELV/PELV together on a single switch actuator.
Do not connect any three-phase motors. Device can be damaged.
Do not use the current detection and load monitoring functions for safety-related
applications e.g. overload detection.
For the outputs, use circuit breakers for the respective rated current. Device can be
damaged.
These instructions are an integral part of the product, and must remain with the end
customer.
2 Device components
Figure 1: View of switch actuator 4gang
(1) Slide switch/Status indication
(2) Programming button and LEDs
(3) KNX connection
(4) Connection of relay outputs
1/8
82560323
J:0082560323 03.09.2013
3 Function
System information
This device is a product of the KNX system and complies with the KNX directives. Detailed
technical knowledge obtained in KNX training courses is a prerequisite to proper
understanding.
The function of this device depends upon the software. Detailed information on loadable
software and attainable functionality as well as the software itself can be obtained from the
manufacturer´s product database.
Planning, installation and commissioning of the device are carried out with the aid of KNX-
certified software. Full functionality with KNX commissioning software version ETS3.0d
onwards.
An updated version of the product database, technical descriptions and conversion programs
and other auxiliary programs are available on our Internet website.
Intended use
- Switching of 230 V AC or 24 V AC/DC electrical loads with floating contacts
- Mounting on DIN rail according to EN 60715 in distribution boxes
Product characteristics
- Manual switching of the relays is independent of the bus.
- Operation as NO or NC contacts
- Logic and restraint function
- Switching feedback (bus operation only)
- Switch position display
- Central switching function with collective feedback
- Disabling function for each channel
- Timing functions: switch-on delay and run-on time, staircase lighting timer with pre-warning
function
- Integration into light scenes
- Operating hours meter, configurable via bus
- Input monitoring for cyclical updating with safety circuit
- No additional power supply necessary
i When controlled by a central telegram the relay outputs of the actuator switch with a slight
time delay.
Additional characteristics of C load switch actuators
- Current detection: measurement of the load current for each output
- Monitoring of threshold values for load monitoring, e.g. for reporting load drop-out
- Switching of capacitive loads and the resulting high switch-on currents
4 Operation
Switching relay contacts manually
The status of the relay is reflected by the slide switches (1) on the front of the device (figure 1).
At the same time they can be used for manual operation of the relay outputs using a suitable
tool.
o Move slide switch to ON position.
Relay contact is closed, load is switched on.
o Move slide switch to OFF position.
Relay contact is open, load is switched off.
i The position of the slide switch immediately reflects the status of the relay, regardless of
whether the output is in NO or NC mode of operation.
i Manual switching of the relays is independent of the bus. Thus in case of manual switching
there will be no feedback via the bus.
i Outputs disabled via software can still be switched manually.
2/8
82560323
J:0082560323 03.09.2013
Switch actuator
5 Information for electrically skilled persons
5.1 Fitting and electrical connection
DANGER!
Electrical shock when live parts are touched.
Electrical shocks can be fatal.
Before carrying out work on the device or load, disengage all the
corresponding circuit breakers. Cover up live parts in the working environment.
Fitting the device
Observe the temperature range. Ensure adequate cooling.
o Mount device on DIN rail. Output terminals must be at the top.
Figure 2
Connecting the device
Note permitted loads.
o Move relay to the OFF position.
o Connect device as shown in the connection example (figure 2).
o Connect bus line with bus connection terminal.
i Various external conductors can be connected.
i Devices for C loads use non-contact current sensors for current measurement. Magnetic
fields in the immediate vicinity may distort the current measurement. Lay forward and
return conductors next to each other as close as possible. Do not install in the immediate
vicinity any devices that generate magnetic fields, e.g. doorbell transformers, power
contactors, etc.
Installing the cover
It is necessary to install a cover to protect the bus connection against hazardous voltages in the
connection area.
3/8
82560323
J:0082560323 03.09.2013
Switch actuator
Figure 3: Installing the cover
o Route the bus line towards the rear.
o Install cover on top of the bus terminal so that it snaps into place (figure 3).
Removing the cover
Figure 4: Removing the cover
o Press the cover to the side and pull it off (figure 4).
5.2 Commissioning
Load the address and the application software
o Switch on the bus voltage.
o Assign physical address.
o Load the application software into the device.
o Note the physical address on the device label.
6 Appendix
6.1 Technical data
KNX
KNX medium TP 1
Commissioning mode S-mode
4/8
82560323
J:0082560323 03.09.2013
Switch actuator
Rated voltage KNX DC 21 ... 32 V SELV
Connection type for bus Connection terminal
Power consumption KNX
Art. No. 2302.16 REG HM typical 150mW
Art. No. 2304.16 REG HM typical 150mW
Art. No. 2308.16 REG HM typical 150mW
Art. No. 2304.16 REG C HM typical 240mW
Art. No. 2308.16 REG C HM typical 240mW
Power loss
Art. No. 2302.16 REG HM max. 2W
Art. No. 2304.16 REG HM max. 4W
Art. No. 2308.16 REG HM max. 8W
Art. No. 2304.16 REG C HM max. 4W
Art. No. 2308.16 REG C HM max. 8W
Ambient conditions
Ambient temperature -5 ... +45 °C
Storage/transport temperature -25 ... +70 °C
Current detection (sine)
Mains frequency
Art. No. 2302.16 REG HM —
Art. No. 2304.16 REG HM —
Art. No. 2308.16 REG HM —
Art. No. 2304.16 REG C HM 50 / 60Hz
Art. No. 2308.16 REG C HM 50 / 60Hz
Measuring range
Art. No. 2302.16 REG HM —
Art. No. 2304.16 REG HM —
Art. No. 2308.16 REG HM —
Art. No. 2304.16 REG C HM 0.25 ... 16A
Art. No. 2308.16 REG C HM 0.25 ... 16A
Accuracy (≤ 1 A)
Art. No. 2302.16 REG HM —
Art. No. 2304.16 REG HM —
Art. No. 2308.16 REG HM —
Art. No. 2304.16 REG C HM ± 100mA
Art. No. 2308.16 REG C HM ± 100mA
Accuracy (> 1 A)
Art. No. 2302.16 REG HM —
Art. No. 2304.16 REG HM —
Art. No. 2308.16 REG HM —
Art. No. 2304.16 REG C HM ± 8 % of curr. val.
Art. No. 2308.16 REG C HM ± 8 % of curr. val.
Switching outputs
Contact type µ contact
Switching voltage AC 250 / 400 V
Switching current 230 V AC 1 16 A
Switching current 230 V AC 3 10 A
Switching current 400 V AC 1 10 A
Switching current 400 V AC 3 6 A
Fluorescent lamps
Art. No. 2302.16 REG HM 10AX
Art. No. 2304.16 REG HM 10AX
Art. No. 2308.16 REG HM 10AX
Art. No. 2304.16 REG C HM 16AX
Art. No. 2308.16 REG C HM 16AX
Ohmic load 3680 W
Capacitive load
Art. No. 2302.16 REG HM 10 A / 140 µF
Art. No. 2304.16 REG HM 10 A / 140 µF
Art. No. 2308.16 REG HM 10 A / 140 µF
Art. No. 2304.16 REG C HM 16 A / 200 µF
Art. No. 2308.16 REG C HM 16 A / 200 µF
Switching voltage DC DC 12 ... 24 V
5/8
82560323
J:0082560323 03.09.2013
Switch actuator
Switching current DC 16 A
Minimum switching current 100 mA
Switch-on current 150 µs
Art. No. 2302.16 REG HM 400A
Art. No. 2304.16 REG HM 400A
Art. No. 2308.16 REG HM 400A
Art. No. 2304.16 REG C HM 600A
Art. No. 2308.16 REG C HM 600A
Switch-on current 600 µs
Art. No. 2302.16 REG HM 200A
Art. No. 2304.16 REG HM 200A
Art. No. 2308.16 REG HM 200A
Art. No. 2304.16 REG C HM 300A
Art. No. 2308.16 REG C HM 300A
Lamp loads
Incandescent lamps
Art. No. 2302.16 REG HM 2500W
Art. No. 2304.16 REG HM 2500W
Art. No. 2308.16 REG HM 2500W
Art. No. 2304.16 REG C HM 3680W
Art. No. 2308.16 REG C HM 3680W
HV halogen lamps
Art. No. 2302.16 REG HM 2500W
Art. No. 2304.16 REG HM 2500W
Art. No. 2308.16 REG HM 2500W
Art. No. 2304.16 REG C HM 3680W
Art. No. 2308.16 REG C HM 3680W
LV halogen lamps with inductive transformer
Art. No. 2302.16 REG HM 1200VA
Art. No. 2304.16 REG HM 1200VA
Art. No. 2308.16 REG HM 1200VA
Art. No. 2304.16 REG C HM 2000VA
Art. No. 2308.16 REG C HM 2000VA
LV halogen lamps with Tronic transformer
Art. No. 2302.16 REG HM 1500W
Art. No. 2304.16 REG HM 1500W
Art. No. 2308.16 REG HM 1500W
Art. No. 2304.16 REG C HM 2500W
Art. No. 2308.16 REG C HM 2500W
Fluorescent lamps T5/T8
uncompensated
Art. No. 2302.16 REG HM 2500W
Art. No. 2304.16 REG HM 2500W
Art. No. 2308.16 REG HM 2500W
Art. No. 2304.16 REG C HM 3680W
Art. No. 2308.16 REG C HM 3680W
parallel compensated
Art. No. 2302.16 REG HM 1300 W / 140 µF
Art. No. 2304.16 REG HM 1300 W / 140 µF
Art. No. 2308.16 REG HM 1300 W / 140 µF
Art. No. 2304.16 REG C HM 2500 W / 200 µF
Art. No. 2308.16 REG C HM 2500 W / 200 µF
Duo circuit
Art. No. 2302.16 REG HM 2300 W / 140 µF
Art. No. 2304.16 REG HM 2300 W / 140 µF
Art. No. 2308.16 REG HM 2300 W / 140 µF
Art. No. 2304.16 REG C HM 3680 W / 200 µF
Art. No. 2308.16 REG C HM 3680 W / 200 µF
Compact fluorescent lamps
uncompensated
Art. No. 2302.16 REG HM 2500W
Art. No. 2304.16 REG HM 2500W
Art. No. 2308.16 REG HM 2500W
6/8
82560323
J:0082560323 03.09.2013
Switch actuator
Art. No. 2304.16 REG C HM 3680W
Art. No. 2308.16 REG C HM 3680W
parallel compensated
Art. No. 2302.16 REG HM 1300 W / 140 µF
Art. No. 2304.16 REG HM 1300 W / 140 µF
Art. No. 2308.16 REG HM 1300 W / 140 µF
Art. No. 2304.16 REG C HM 2500 W / 200 µF
Art. No. 2308.16 REG C HM 2500 W / 200 µF
Mercury vapour lamps
uncompensated
Art. No. 2302.16 REG HM 2000W
Art. No. 2304.16 REG HM 2000W
Art. No. 2308.16 REG HM 2000W
Art. No. 2304.16 REG C HM 3680W
Art. No. 2308.16 REG C HM 3680W
parallel compensated
Art. No. 2302.16 REG HM 2000 W / 140 µF
Art. No. 2304.16 REG HM 2000 W / 140 µF
Art. No. 2308.16 REG HM 2000 W / 140 µF
Art. No. 2304.16 REG C HM 3680 W / 200 µF
Art. No. 2308.16 REG C HM 3680 W / 200 µF
Housing
Fitting width
Art. No. 2302.16 REG HM 72mm / 4modules
Art. No. 2304.16 REG HM 72mm / 4modules
Art. No. 2308.16 REG HM 144mm / 8modules
Art. No. 2304.16 REG C HM 72mm / 4modules
Art. No. 2308.16 REG C HM 144mm / 8modules
Weight
Art. No. 2302.16 REG HM approx. 170g
Art. No. 2304.16 REG HM approx. 220g
Art. No. 2308.16 REG HM approx. 400g
Art. No. 2304.16 REG C HM approx. 270g
Art. No. 2308.16 REG C HM approx. 500g
Connection of outputs
Connection mode Screw terminal
single stranded 0.5 ... 4 mm²
finely stranded without conductor sleeve 0.5 ... 4 mm²
finely stranded with conductor sleeve 0.5 ... 2.5 mm²
6.2 Troubleshooting
Operation via bus is not possible
Cause: No bus voltage.
Switch on bus voltage, check installation.
Cause: Application software has been stopped, programming LED is flashing.
Disconnect device from bus, wait 5 seconds and reconnect to bus.
Cause: Application software missing or faulty.
Check programming and correct.
6.3 Warranty
We reserve the right to make technical and formal changes to the product in the interest of
technical progress.
We provide a warranty as provided for by law.
Please send the device with a description of the defect to our central customer service office.
7/8
82560323
J:0082560323 03.09.2013
Switch actuator
ALBRECHT JUNG GMBH & CO. KG
Volmestraße 1
58579 Schalksmühle
Telefon: +49.23 55.8 06-0
Telefax: +49.23 55.8 06-2 04
www.jung.de
Service Center
Kupferstr. 17-19
44532 Lünen
Germany
8/8
82560323
J:0082560323 03.09.2013
Switch actuator
Dieses Handbuch passt für folgende Modelle
4
Inhaltsverzeichnis
Andere Jung Controller Handbücher
Jung
Jung KNX 2095 LUX Bedienungsanleitung
Jung
Jung BTJ1B2U Bedienungsanleitung
Jung
Jung KNX 2131.16 UP Bedienungsanleitung
Jung
Jung Smart Control SC 1000 KNX Bedienerhandbuch
Jung
Jung KNX 2136 REG HZ Bedienungsanleitung
Jung
Jung KNX 230 .16 REGHM Series Bedienungsanleitung
Jung
Jung FM ST 50 UP Bedienungsanleitung
Jung
Jung LB management Bedienungsanleitung
Jung
Jung KNX 2095 LUX Bedienungsanleitung
Jung
Jung FMJ50700UP Bedienungsanleitung
Jung
Jung KNX 230021 SU Bedienungsanleitung
Jung
Jung 230061SR Bedienungsanleitung
Jung
Jung RCD 20 series Bedienungsanleitung
Jung
Jung 240-10 Bedienungsanleitung
Jung
Jung FM J 50700 REG Bedienungsanleitung
Jung
Jung 390041SR Bedienungsanleitung
Jung
Jung FA 10 EB Bedienungsanleitung
Jung
Jung KNX 519 KRMTSD Series Bedienungsanleitung
Jung
Jung 2336 REG HZ B Bedienungsanleitung
Jung
Jung FA 10 REG Bedienungsanleitung
