Juniper EX8200 Series Bedienungsanleitung

Removing an AC Power Supply from an EX8200 Switch

The AC power supply in an EX8200 switch is a hot-removable and hot-insertable

field-replaceable unit (FRU). You remove AC power supplies from the front of the

chassis.

CAUTION: Before you remove a power supply, ensure that you have power supplies

sufficient to power the switch left in the chassis. See Calculating Power Requirements

for an EX8208 Switch or Calculating Power Requirements for an EX8216 Switch.

Before you remove an AC power supply from the switch:

■Ensure you understand how to prevent ESD damage. See Prevention of

Electrostatic Discharge Damage on EX Series Switches.

Ensure that you have the following parts and tools available to remove an AC power

supply from an EX8200 switch chassis:

■Electrostatic discharge (ESD) grounding strap

■Phillips (+) screwdriver, number 1

■Replacement power supply or a cover panel for the power supply slot

CAUTION: Do not leave the power supply slot empty for a long time while the switch

is operational. Either replace the power supply promptly or install a cover panel over

the empty slot.

To remove an AC power supply from an EX8200 switch (see Figure 1):

1. Attach the electrostatic discharge (ESD) grounding strap to your bare wrist, and

connect the strap to the ESD point on the chassis.

2. Flip the Enable switch next to the appliance inlet on the power supply to the

Standby position.

3. Disconnect power from the switch by performing one of the two following tasks:

■If the AC power source outlet has a power switch, set it to the OFF position.

■If the AC power source outlet does not have a power switch, gently pull the

male end of the power cord connected to the power source outlet out of the

outlet.

4. Remove the power cord from the AC appliance inlet on the AC power supply

faceplate.

5. Turn the adjustment nut of the power cord retainer counterclockwise till you can

see the power cord. Pull the power cord from the slot in the adjustment nut.

Removing an AC Power Supply from an EX8200 Switch ■1

6. Squeeze the two sides of the power cord retainer clip, and pull the L-shaped ends

of the clip from the holes on each side of the AC appliance inlet to completely

remove the power retainer clip.

7. Unscrew the captive screw counterclockwise using the Phillips (+) screwdriver,

number 1.

8. Pull the captive screw away from the faceplate of the power supply to release

the latch.

9. Pull the handle away from the faceplate of the power supply until it is

perpendicular to the faceplate.

10. Taking care not to touch power supply components, pins, leads, or solder

connections, place one hand under the power supply to support it. Grasp the

power supply handle with your other hand and pull the power supply completely

out of the chassis.

11. If you are not replacing the power supply, install the cover panel over the slot,

using the Phillips (+) screwdriver to tighten the screw on the side of the cover

panel.

Figure 1: Removing an AC Power Supply from an EX8200 Switch

Related Topics Installing an AC Power Supply in an EX8200 Switch■

■AC Power Supply in an EX8200 Switch

Published: 2009-07-15

2■Removing an AC Power Supply from an EX8200 Switch

Andere Handbücher für EX8200 Series

13

Inhaltsverzeichnis

Andere Juniper Schalten Handbücher

Juniper

Juniper QFX5200-32C-L Bedienungsanleitung

Juniper

Juniper 200 Series Bedienungsanleitung

Juniper

Juniper QFX10008 Bedienungsanleitung

Juniper

Juniper EX Series Bedienungsanleitung

Juniper

Juniper QFX5230-64CD Montageanleitung

Juniper

Juniper EX4500 Series Bedienungsanleitung

Juniper

Juniper EX Series Bedienungsanleitung

Juniper

Juniper QFX5100-48T Bedienungsanleitung

Juniper

Juniper EX4300 Bedienungsanleitung

Juniper

Juniper EX2200-C Bedienungsanleitung

Juniper

Juniper EX4300 Montageanleitung

Juniper

Juniper EX2200 Series Montageanleitung

Juniper

Juniper EX4600 Montageanleitung

Juniper

Juniper EX2200 Series Montageanleitung

Juniper

Juniper EX3200 Series Bedienungsanleitung

Juniper

Juniper QFX3000-G QFabric Kurzanleitung

Juniper

Juniper QFX5200 Montageanleitung

Juniper

Juniper EX8216 Bedienungsanleitung

Juniper

Juniper EX4500-40F-FB Bedienungsanleitung

Juniper

Juniper EX 3200 24T Bedienungsanleitung

Juniper

Juniper EX8208 Bedienungsanleitung

Juniper

Juniper Day One+ Bedienungsanleitung

Juniper

Juniper EX9253 Montageanleitung

Juniper

Juniper QFX10002 Montageanleitung

Beliebte Schalten Handbücher anderer Marken

URC

URC Total Control MFS-8 Bedienungsanleitung

Azbil

Azbil HPQ-D11 Bedienungsanleitung

Sony

Sony DFS-900M Bedienungsanleitung

SICK

SICK i17S Bedienungsanleitung

F&F

F&F SZR-277 Bedienungsanleitung

Shure

Shure UAMS/BK Bedienungsanleitung

Dräger

Dräger X-zone Switch Off Bedienungsanleitung

Asco

Asco Joucomatic 349 Series Bedienungsanleitung

BT

BT Mini Hub Bedienungsanleitung

D-Link

D-Link DES-1226G Bedienungsanleitung

Johnson Controls

Johnson Controls FS80-C Bedienungsanleitung

Alcatel-Lucent

Alcatel-Lucent 7450 ESS-12 Bedienungsanleitung

MicroNet

MicroNet SP1200A Bedienungsanleitung

Ruijie

Ruijie RG-PF2920 Series Installations- und Betriebsanleitung

Altinex

Altinex DA1914SX Bedienungsanleitung

MiLAN

MiLAN MIL-SM2401M Bedienungsanleitung

RJM

RJM MASTERMIND PBC/6X Bedienungsanleitung

Atlas

Atlas MMK-KVM8 Bedienungsanleitung