JVC KD-R420J Handbuch

Andere Handbücher für KD-R420J

1

Dieses Handbuch passt für folgende Modelle

15

Inhaltsverzeichnis

Beliebte Autoradiosystem Handbücher anderer Marken

JL Audio

JL Audio Stealthbox SB-CAN-G2MVX3D/10TW3 Bedienungsanleitung

Clarion

Clarion PU-9836A Bedienungsanleitung

Sony

Sony MEX-BT5750U Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric AR0M Bedienungsanleitung

Sony

Sony RM-X7BT Bedienungsanleitung

Insignia

Insignia NS-HD5113 Bedienungsanleitung

Clarion

Clarion BTD3341 Bedienungsanleitung

USA SPECS

USA SPECS PA11-VW6 Bedienungsanleitung

Sony

Sony MEX-N4380BT Bedienungsanleitung

Kenwood

Kenwood KCD-BT6544U/UY Bedienungsanleitung

Philips

Philips CSQ405/98 Bedienungsanleitung

Alpine

Alpine TDM-7544 Bedienungsanleitung

Autotek

Autotek TransAm TA 1400 Bedienungsanleitung

Clarion

Clarion PN-3124N-A Bedienungsanleitung

Denso TEN

Denso TEN FT0108A Bedienungsanleitung

Pyle

Pyle PLD57MU Bedienungsanleitung

Harman

Harman Chrysler Radio Navigation System RB4 Bedienungsanleitung

Clarion

Clarion VS735 Bedienungsanleitung

(1/2)

TP 8/12/11

JVC U.S.A.

Customer Care Center 1-800-252-5722

CUSTOMER PROCEDURE

“Chk Wiring then reset unit” message scrolls on display when unit is powered ON

KD-R320J KD-R420J KD-R520J KD-HDR44J KD-BPT30J KD-R328J

KD-R428J KD-R528J KD-BTP50J KD-A525J KD-A625J KD-R620J

KD-R628J KD-AHD79J KD-HDR70J KW-HDR720J

Cause

The wires were shorted during installation.

Cure

1. Remove the Radio and disconnect the Harness.

2. Verify the Units wiring and ensure there are no shorts.

 Check for misconnection (for example; DC12V to Left speaker negative to

reverse signal)

 Check for loose connections

 Check for uncovered connections

3. Clear the error using the procedure below.

PROCEDURE

Apply this procedure after verifying the units wiring.

It is NOT possible to clear the error message if the wiring problem has not been

corrected.

1. Remove wiring harness from unit (remove all DC power).

2. Simultaneously press and hold the [MENU] and [UP arrow] button.

3. While holding [Menu] / [Up arrow] buttons, insert the unit’s wiring harness

(reapply DC power to the unit).

a. “DC ERR” will be displayed.

b. If “Chk wiring…” message reappear, retry steps 1-3 again.

(2/2)

TP 8/12/11

4. Press the [Up arrow]; “DC1 ERR” may be displayed.

5. Press and Hold the [Up arrow] to clear any error; “DC1 OK” will display.

6. Press the [Down arrow], “DC2 *” will display.

a. “ * ” will be a number 0 to 4

7. Press and Hold the [Down arrow] to clear any error; “DC2 0” will display.

8. Remove the wiring harness from the unit (remove all DC power).

9. Remove the units Faceplate.

10. Insert the unit’s wiring harness (reapply DC power to the unit).

11. Press the [Reset] button on the unit to reset it.

12. Reinstall the units Faceplate and Power ON the unit.

a. Operation should be restored.

b. If “Chk wiring…” occurs again, the unit maybe defective. Contact a JVC

authorized service center for assistance.