K-Mate BTH108R Bedienungsanleitung

BTH108R

True Wireless Bluetooth Headset

User’s manual

Contents

Brief introduction…………...…………………………..…... 1

Before use……………………………………………………. 1

1. Overview…………………………………………………...……1

2. Charging for headset..……………………………………………2

2. Charging for charging case..…………………………………3

Getting started……..…………………………………………4

1. Wearing headset.............................................................4

2. One earbud connecting with cellphone......................................4

3. Two earbuds connecting with cellphone..........................................6

4. Earbuds pairing/connecting........................................................6

5. Function operation-use one earbud ....................................7

6. Function operation-use two earbuds ....................................9

7. Battery display........................................................................ ....10

8. Prompt tone……………………………………………….....10

9. Factory Reset……………………………………………..…...10

Care and maintenance……………………………..……….11

FAQs……………………………………...…………………..11

Specification……………………………...………………..…12

Welcome to use this True Wireless Bluetoothheadset, BTH108R. Please read

this user’s manual carefully before use.

Brief introduction

BTH108R is a True Wireless Bluetooth Headset ,each ear piece comes with

a Microphone that can be used individually or used together for stereo

sound.The headset supports music and calling function,as well as touch

sensitive playback and pause control.

Before use

1. Overview

Charging indicator light

MFB touch-button

Charging metal contact

LED indicator (blue)

Charging jack

Microphone

LED indicator (red)

Big/medium/small Ear tips

2. Charging for headset

When the headset is low on power, the headset emits “Battery low” once

every 2 minutes and thered Led flashes slowly four times every 1 minute.

Please recharge the battery of the headset.

The way of charging for the earbuds as following:

Using USB cable

1. Put the earbuds into the charging case to ensure that the charging device

connect well, and start charging when you see the red indicator light of

the earbuds on.

Red light on: Charging

Red light off: Finish charging

2. Charging should be completed in roughly 1.5 hours.

Remarks:

The left and right earbuds on charging case of an arbitrary charge can be

charged.

Please cover the charging case cover, so that the earbuds and the

charging case connect well when it is charging.

3. Charging for charging case

When any of the following situations occurs during the use, it indicates that

the charging case has gone into sleep mode with low power. You need to

charge the charging case:

1) After putting the earphone into the charging case, the earphone will not

automatically shut down or turn on the red light.

2) During charging, the headset suddenly turn on automatically.

3) Removing the earbuds from the charging case will not automatically turn

on.

The way of charging for the charging case as following:

Using USB cable

1) Plug the micro USB charging cable into the case’s charging jack.

2) Plug the USB cable into a USB port of PC or a 5Volt USB charge.

Red light on: Charging

Red light off: Finish charging

3) Charging should be completed in roughly 1.5 hours.

4) If the earbuds are in the charging case, it can charge the earbuds while

charging the charging case.

Remarks:

1) The battery is recyclable.

2) Batteries (battery pack or batteries installed) shall not be exposed to

excessive heat place, such as sunshine, fire or the like.

3) Please make sure the charging jack is dry before charge.

Getting started

1. Wearing headset

a. Choose the suitable size ear tips

b. Ensure each earbuds is worn on the correct ear. “L”should be worn on the

left ear and “R”worn on the right ear.

Left ear Right ear

2.One earbud connecting with cellphone

Each earbuds can be worn singly as Bluetooth headset。

1. Power on

1)When charging, the earbuds will turn on automatically when they are

taken out of the charging case.

2)Press touch-button for about 3s until blue LED flashes as the same time

the headset emits “Power on”. Then release. This is now in the “Power

on”state.

2.Pairing

1) Press touch-button for about 5s and release it when the red LED and

blue LED flash quickly and alternately. The earbuds are in”Pairing”mode

2) When the earbuds and the cellphone fails to connect back, the earbuds

will automatically enter the matching state.

3.Connecting

To connecting your headphone to a Bluetooth device, first ensure the device

has Bluetooth enable and it is in pairing mode(See your device manual for

setting pairing mode) . Then put your headphones into pairing mode by

pressing the power button until the LED light flashes red and blue

alternatively.

Once your headphones are in pairing mode, you should be able to see it in

the list of Bluetooth devices.

You should see BTH108R-L for left earbuds and BTH108R-R for the right

earbuds appear in your contactable devices list.

You need to connect both to use them as a stereo headset.However,if you

want to use them singly,only connect the desired ear L or R.

4.Power off

1）Auto power off once put into charging case

2）Press touch-button about 3s and release it till red LED is on,and earbuds

prompt “Power off”.

Remark:

The earbuds will automatically connect with the latest Bluetooth device

when power on again.If the earbuds are not connected, they will enter

into pairing mode automatically.

Each earbuds will automatically switch to standby mode if disconnected

from device(blue LED flash once every 2 seconds), and will power off

automatically after 2 minutes to save power.

The operation of single earbud is the same as that of double earbuds.

3.Two earbuds connecting with cellphone

In this mode use two earbuds at the same time to enjoy stereo sound.

Turn on the main earbud (BTH108R-L) and connect it with you Bluetooth

device,then power on the other earbud and it will connect with each other

automatically.

Remarks:

Pairing mode lasts for 2 minutes,the headsets will switch to power off

mode if no device connected within that time.

The headset will connected with the latest device and successfully paired

automatically when powered on.

If the headset is disconnected from the device beyond the distance, it will

automatically power off after 5 minutes, and it will automatically connect

when it returns to the effective distance within the first 3 minutes.

4.Earbuds pairing/connecting

Please use this step if two headset can not be connect with each

other.

1.Turn off two earbuds respectively(don’t put them into the charging case).

2.Clear the pairing list: Choose one of the earbuds. Firstly, enter the pairing

mode.Then hit the touch button 5 times, while the red light turns on for 1

second. The pairing list will be cleared when emits"Power off" after a

"dang"prompt. The other headset cleans the pairing list by doing the same.

3.The earbuds will enter TWS pairing mode automatically when they are

turned on (indicator light status: red and blue lights flash slowly).After

successful connection, the master earbud(L) will emits ‘Connected’and

‘Pairing’, which indicator light status will be: red LED and blue LED

flash alternately(it keeps waiting to be paired with your phone), while the

secondary earbud(R) will emits ‘Connected’and indicator status will be:

blue LED flash twice time every 10 seconds.

Remarks:

In normally the two earbuds will connect automatically once you have

taken out of the charging case,which set in factory.

You can connect the two earbuds according above operation if they failed

connecting.

TWS mode : Only left earbuds can be the master one,which can

connectthe rightearbuds and the phone’s Bluetooth at the same time.

When the right earbuds connect with left earbuds in the TWS mode, it

cannot connect with the phone’s Bluetooth.

5.Function operation-use one earbud

a.Answering /rejecting phone calls

When calling(blue LED quick flash),clicking the touch button once will

answer the call.Clicking the touch button a second time will hang up the

call.

Tap touch button to answer/reject a call

b.Reject calling

When your paired phone rings(blue LED quick flash), long press the touch

button and release to reject the call. You will hear an audio confirmation

tone.

Long press touch button about 2s to reject a call

c.Voice assistant

After connecting your headphone with a Bluetooth compatible music

player(blue LED flash twice every 10s), triple clicking the touch

button(prompt‘Voice dial’) will active voice assistants like Siri.

Triple click the touch button to active voice assistant

d.Transfer conversation between earbuds and mobile phone

Transfer conversation to mobile phone : During a call , long press the touch

button about 2 secondwhile you will hear a ‘dang’tone. Long press the

touch button again to Transfer conversation to earbuds.

Long press touch button about 2s

e.Playing/Pause

After connecting your headphone with a Bluetooth compatible music

player,double clicking the touch button will play music,double clicking

again will pause playback.

Double click

Inhaltsverzeichnis

Andere K-Mate Headset Handbücher

Beliebte Headset Handbücher anderer Marken

Sena

Sena SMH10 Bedienungsanleitung

IASUS

IASUS Stealth IA-NT4-BASIC-BT Bedienungsanleitung

Sennheiser

Sennheiser EPOS ADAPT 230 Bedienungsanleitung

Doro

Doro Flexus HS2005 Bedienungsanleitung

GE 98971 Bedienungsanleitung

Hama

Hama 00184070 Bedienungsanleitung

Plantronics

Plantronics Blackwire 3200 Series Bedienungsanleitung

Blue Tiger

Blue Tiger Advantage PLUS Bedienungsanleitung

Jawbone

Jawbone Icon Bedienungsanleitung

Jabra

Jabra FR 20 Bedienungsanleitung

Roxcore

Roxcore Flow A+ Bedienungsanleitung

Turtle Beach

Turtle Beach XP 510 Bedienungsanleitung

Philips

Philips SHB6101 Bedienungsanleitung

Jabra

Jabra PRO 9460 Duo Bedienungsanleitung

HyperX

HyperX HyperX Cloud Flight Bedienungsanleitung

Bose

Bose MIE2 Mobile Bedienungsanleitung

Jabra

Jabra Steel Bedienungsanleitung

HyperX

HyperX cloud ii Bedienungsanleitung