K-Rain RPS469 Bedienungsanleitung
Station ModelS - Available in 4, 6 or 9 stations.
oUtdoor Model - Supplied with 120VAC x 24 AC or 240VAC (International)
x 24VAC inbuilt transformer.
OPTIONAL LEAD WITH PLUG.
INSTRUCTION MANUAL
Mid-Size irrigation Controller
www.krain.com
INTRODUCTION ............................................1
GLOSSARY ..................................................2
KEY FEATURES ............................................3
PROGRAMMING INSTRUCTIONS
Introduction ................................................4
Set automatic program ..............................4
General tips for easy programming ...........5
PROGRAMMING
Set current time & correct day ...................6
Set calendar
...............................................6
Set start times ...........................................7
Set watering days ..................................8-9
Set station run times ............................9-10
MANUAL OPERATIONS
Run a single station ..................................11
Run a system test ..............................11-12
Run a program ...................................12-13
Stop watering ..........................................14
Stacking start times .................................14
Automatic back up ...................................14
OTHER FEATURES
Rain sensor .........................................15-16
Rain delay ................................................16
STOP all watering ................................16-17
Water budgeting & seasonal
adjustment ..............................................17
SPECIAL FUNCTIONS
Pump ON/OFF selection.......................18-19
Pressure build ....................................19-20
Water hammer saver ................................20
INSTALLATION INSTRUCTIONS
Mounting the controller ............................21
Electrical hook-up ....................................21
Field wiring connections .....................21-22
Terminal block layout ..............................22
Pump Start Relay Connection ...................23
Pump Installation ......................................23
Master valve installation ...........................24
Pump protection (system test) ..................25
TROUBLE SHOOTING GUIDE ..................26-27
ELECTRICAL CHARACTERISTICS
Electrical outputs ......................................28
SERVICING THE CONTROLLER ....................29
SPARE WATERING PLANNER ................30-31
WARRANTY ...............................................34
CONTENTS
1
RPS469 is available in 4, 6 and 9 station configurations. Designed to cover a wide range of
applications from residential and commercial turf, to light agriculture, and professional nursery.
This controller has a possible 6 separate programs with up to 36 starts per day. The controller has
a 7 day watering schedule with individual day selection per program or a 365 calendar for odd/even
day watering or selectable interval watering schedules from every day to every 15th day. Individual
stations can be allocated to one or all programs and can have a run time of 1 minute to 12 hours 59
minutes or 25 hours if the water budget is set to 200%.
K-Rain has always been concerned with sustainable water usage. The controller has many water
saving features that can be used to maintain the highest standard of plant quality with the least
amount of water consumption. The integrated budget facility allows global changes of run times
without affecting programmed run times. This allows for decreasing total water consumption on days
of minimal evaporation.
INTRODUCTION
2
GLOSSARY
FRONT MOUNTED
SENSOR SWITCH
ON/OFF switch for easy
access to override
TERMINAL COVER
Easy to remove for
easy access
LARGE HIGH CONTRAST LCD
Displays all
programming information
LARGE SELECTION DIAL
Navigates through all
programming information
QUICK PROGRAM SELCTION KEY
The “P” key allows faster program
entry and
review
LARGE MENU BUTTONS
Easy operation with fast scroll
feature for entry and review
3
KEY FEATURES
4,6 & 9 station models.
Indoor/Outdoor model with built-in transformer.
6 programs, each of which has 6 start times. Maximum of 36 start times per day.
Station run times from 1 minute to 12 hours & 59 minutes.
Selectable watering options:
- Individual 7 day selection.
- Odd or Even day selection.
- Interval watering day selection from every day to every 15th day.
Watering budgeting feature allows quick adjustment of the station run times by
percentage, from 10% to 200%.
Rain sensor input will turn off all stations or selected stations during wet periods,
if a sensor is installed.
Permanent memory feature will retain automatic programs during power failures.
Standard 9 volt battery can be used to program the controller remotely
and to maintain the clock.
Manual functions:
- Run a program or group of programs once.
- Run a single station.
- Run a test cycle for all stations.
- “OFF” position, stops a watering cycle or to stop automatic
programs during winter.
Pump or master valve input is standard.
Pump or master valve input can be turned off by program or by individual stations,
for dual water supply situations or if stations are used to turn on garden lights.
LARGE MENU BUTTONS
Easy operation with fast scroll
feature for entry and review
4
PROGRAMMING INSTRUCTIONS
INTRODUCTION
This controller has been designed with 6 separate programs to allow different landscape areas to
have their own individual watering schedules. A program is a method of grouping stations (valves)
with similar watering requirements to water on the same days. These stations will water
in sequential order and on the days selected.
Group the stations (valves) which are watering similar landscape areas together.
Examples: Turf, flower beds, gardens. These different groups may require individual
watering schedules, or programs.
Plan your watering schedule completing the planner supplied at the back of this book.
Set the current time and correct day of the week. If odd or even day watering is going to be
used, make sure the current year, month and day of the month is correct.
HINT: To select a different program use the button marked .Each press will move to the next
program number. This is handy for quick reviewing of previously entered information without losing your
place in the programming cycle.
SET AUTOMATIC PROGRAM
Set the automatic program for each group of stations (valves) by completing the
following three steps:
1. Set start times
This sets the time when the watering schedule is to commence.
NOTE: For each start time, all the stations (valves) selected for the program will come
on in sequential order. If two start times are set, the stations (valves) will come on twice.
2. Set Watering Days
These are the selected days when the automatic system will be active.
3. Set Station Run Times
This sets the watering duration required for each station (valve).
5
PROGRAMMING INSTRUCTIONS
GENERAL TIPS FOR EASY PROGRAMMING
This controller has been designed for quick intuitive programming.
Remember these simple tips for hassle free programming.
1. Complete the spare watering planner at the back of this book.
2. When setting, one push of the button will increment one unit.
3. Holding one button down will fast scroll through units.
4. During the programming, only flashing units are able to be set.
5. Adjust flashing units using the or buttons.
6. Pressing will scroll forward through the settings in an orderly sequence.
7. Pressing will scroll back to previous settings and setting can be changed.
The is used to select different programs. Each push
on this button will increment one program number.
Once you have selected the primary function and
program you wish to alter, you can then use the
or to change that function’s value.
Only display elements that are flashing can be altered
with the keys.
Use the to scroll through other values within
the function that can be altered.
INCREASE VALUE
(+)
(-)
DECREASE VALUE
SCROLL
FORWARD
SCROLL
BACK
The large dial is the primary
device for selecting an operation.
Rotate the dial to the function
you wish to alter or review.
6
PROGRAMMING
SET CURRENT TIME & CORRECT DAY
Turn the dial to “Set Clock/Calendar” position.
The hour will be flashing. Use the or to adjust.
NOTE: AM/PM must be set correctly.
Press button and the “minutes” will flash. Use or to adjust
the minutes.
Press and the “day of the week” will flash. Use or to set the
correct day.
SET CALENDAR
NOTE: The calendar only needs to be set when selecting Odd/Even day watering in areas where water
restrictions may require this feature.
Press button until the year, month and day are shown. The “year” will be flashing. Use
or to adjust if required.
Press and the “month” will flash. Use or to adjust if required.
Press and the “day” will flash. Use or to adjust if required.
HINT: To return to the clock, press and together or turn dial to another position.
Before proceeding, ensure the spare watering planner has been completed. From your planner, you
should be aware which stations (valves) are allocated to each program. Set one program at a time to
ensure that the schedules are completed correctly.
7
Example: SET PROGRAM 1
STEP 1 – SET START TIMES
NOTE:All stations will come on in sequential order for each start time.
Turn the dial to “Set Start Times” and ensure that “Prog No 1” is showing. If not, then use the
button to select “Prog No 1”.
The “Start No” will be flashing. THE DISPLAY WILL SHOW:
Use
or
to change the “Start No” if required, otherwise press
and the “hour” will
flash.
Use or to adjust if required.
NOTE: Ensure AM/PM position is correct.
Press
and the “minutes” will flash.
Use or to adjust if required
.
Each program has up to 6 start times. Should you require a second start time,
press
and “Start1” will flash.
Advance to “Start2” by pressing
.
THE DISPLAY WILL SHOW:
Press
and proceed as per setting Start 1.
HINT: To toggle a start on or off press
or
when the hour is flashing. To change to a different
program either to review or alter, press the
button. Every press will increment to the next program.
PROGRAMMING
8
PROGRAMMING
STEP 2 – SET WATERING DAYS
This unit has interval watering from every day to every 15th day, individual day selection or a 365
day calendar with odd/even day selection in areas where water restrictions require this feature.
INDIVIDUAL DAY SELECTION
Turn the dial to “Set Watering days” and ensure that “Prog No 1” is showing. If not, then use the
button to select “Prog No 1”.
“Monday” will be flashing. THE DISPLAY WILL SHOW:
This refers to Mon being Day1.
To turn Monday off press
the button.
To turn it back on press the
button. To advance
to the next day and set it use the
button, the display will then flash Tue and Day 2. Use
or to turn days ON or OFF
and advance to the next day using
. Remember to set all 7 days
ON or OFF.
ODD/EVEN DAY SELECTION (OPTIONAL)
In some areas users are only allowed to water their landscapes on odd dates if their house number is
odd, or even dates when their house number is even.
This controller allows this to be done simply by setting the relevant selection of odd or even and
setting the current date into the controller. The controller will account for leap years.
If you require the odd/even day option, simply press the button until “Odd” is shown.
Press the button and “Even” will be shown.
This feature may be required in areas where water restrictions are enforced.
Note: Remember to set the 365 day calendar when setting the clock, or this feature will be
out of sequence (refer page 6 “set calendar”).
Inhaltsverzeichnis
Andere K-Rain Timer Handbücher
