Kane IRP-2 Bedienungsanleitung

KANE IRP-2

Infra Red Printer

Stock No: 19056-6 March 2013

Page 2

The KANE IRP-2 is a portable printer using thermal paper that links to other

Kane products using an infra-red link. It incorporates an ‘easy load’ paper

facility and allows NiMh batteries to be recharged in situ.

OPERATING THE PRINTER

BUTTON LAYOUT AND FUNCTIONS

Fig 1:

Fig 2:

ON / OFF

DARKEN CONTRAST

PAPER FEED

LIGHTEN CONTRAST

Page 3

POWER SUPPLY

Power is supplied to the printer in the form of four AA Ni-MH batteries, which can be re-

charged by connecting a 19278 charger to the KANE IRP-2.Fig 2

Note: The 19278 cannot supply the full power requirement to the KANE IRP-2, the batteries

must contain some charge before printing will be possible.

WARNING: Do NOT attempt to recharge non-rechargeable batteries as this can lead

to batteries leaking and over-heating.

WARNING: Do NOT use Alkaline AA batteries.

USING THE KANE IRP-2

Switch the printer on using the power ON/OFF key as shown in fig 1, the status indicator will

become illuminated (RED LIGHT).

Note: The printer will automatically switch off after around 10 minutes of inactivity. To

reactivate, simply press the ON/OFF key. If the battery power falls to low, the current print

will be suspended and the status indicator (RED light) will flash 4 times, connect the power

supply/charger to continue printing.

POSITIONING THE PRINTER AND INSTRUMENT

Ensure that there are no obstructions between the instrument emitter (at the top of the

instrument) and the KANE IRP-2 receiver (By the status indicator).

Angle=0° Distance<=4.5m

Angle=45° Undefined (Horizontal)

Angle=90° Undefined (Vertical)

ADDITIONAL INFORMATION

SELF TEST

Power off the KANE IRP-2, hold down the PAPER FEED key and press POWER ON/OFF

key, the output will be all the letters including the Latin format

PRINT CONTRAST

The contrast of the KANE IRP-2 output can be adjusted both lighter and darker by pressing

the designated keys shown in fig 1.

Page 4

REPLACING THE PAPER ROLL

To replace the paper roll in the KANE IRP-2, release the paper cover by pressing down the

release lever.

Remove the old paper roll core and insert the new roll so that it sits as follows :-

Page 5

Lay the free end of paper over the printer head, past the serrated paper cutter onto the body

of the front of the printer’s case. Now close the paper cover and gently press down until it

locks into place. Start the paper feed sequence to confirm that the paper has been correctly

loaded. Tear off the excess paper by pulling it against the paper cutter.

WARNING. Never pull the paper through the printer always use “paper feed”.

Note: if the ‘paper out’ warning light is still flashing (see below) switch the printer off and then

on again.

STATUS INDICATOR (RED LIGHT)

PAPER OUT

The KANE IRP-2 will automatically detect when the paper has run out, the STATUS

INDICATOR will repeatedly flash.

LOW BATTERY

Low battery is indicated by the STATUS INDICATOR flashing three times.

Connect the 19278 to the charging socket shown in Fig 2.

HEAD THERMAL LIMIT

In the event of extensive printing periods the temperature of the thermal head of the KANE

IRP-2 may rise to an unusable level, if this occurs the STATUS INDICATOR will flash twice

and printing will be suspended until the temperature falls to an acceptable level.

Page 6

CONTROLLING THE PRINT HEAD

If you turn the printer off whilst printing, the print head may stop in the middle of the line. To

return the print head to the left side of the paper, turn the printer on, then off.

MISSING OR MISFORMED CHARACTERS

The █character will show on the print out if the printer has detected incorrect data due to

interference with, or interruption to, the stream of incoming information.

Common causes for this error include incorrect positioning of printer with reference to the

instrument (this can either be due to the distance or the angle of operation), obstruction of

the infrared signal or even interference from another infrared emitting source.

ENVIRONMENTAL LIMITS

The KANE IRP-2 is designed for indoor use only.

Operating temperature: 0

C to 40

C (32

F to 104

Storage temperature: -20

C to 60

C (-4

F to 140

Humidity: 5% to 95% relative at 40

C (104

F) non condensing

BATTERIES

This product is designed for only rechargeable NiMh AA batteries. Four batteries are

needed. Types cannot be mixed.

WARNING: Do NOT attempt to recharge non-rechargeable batteries as this can lead

to batteries leaking and over-heating.

WARNING: Do NOT use Alkaline AA batteries

The battery charger supplied with the product is rated for indoor use only. Its voltage input

must be in the range 100 – 240 V ac at 50 – 60 Hz with a current capability of 0.3 A. The

chargers output voltage is 9 V dc at a maximum of 0.66 A.

The charger has no user serviceable components.

Only a correctly specified and rated charger must be used with the product. Kane part

number is 19278

Page 7

CLEANING

The outer case and protective boot (if applicable) can be cleaned using a damp cloth and

non abrasive detergent. After cleaning leave the product in a warm dry place until the

surfaces are completely dry. Under no circumstance use solvent or hydrocarbon based

products as they can cause serious damage to plastic and rubber.

SERVICING

This product contains no user serviceable parts.

SAFETY

This product has been tested for compliance with EN 61010-1:2010 (Safety requirements for

electrical equipment for measurement, control and laboratory use.) and is certified to be

compliant.

END OF LIFE PRODUCT DISPOSAL

At the end of the product's life it should be re-cycled in accordance with current legislation

and local guidelines.

BATTERY DISPOSAL

Always dispose of depleted batteries using approved disposal methods that protect the

environment.

Page 8

ELECTROMAGNETIC COMPATIBILITY

European Council Directive 89/336/EEC requires electronic equipment not to generate

electromagnetic disturbances exceeding defined levels and have adequate immunity levels

for normal operation. Specific standards applicable to this analyser are stated below.

As there are electrical products in use pre-dating this Directive, they may emit excess

electromagnetic radiation levels and, occasionally, it may be appropriate to check the

analyser before use by:

Use the normal start up sequence in the location where the analyser will be used.

Switch on all localized electrical equipment capable of causing interference.

Check all readings are as expected. A level of disturbance is acceptable.

If not acceptable, adjust the analyser’s position to minimize interference or switch off,

if possible, the offending equipment during your test.

At the time of writing this manual (January 2012) Kane International Ltd are not aware of any

field based situation where such interference has occurred and this advice is only given to

satisfy the requirements of the Directive.

This product has been tested for compliance

with the following generic standards:

EN 61000-6-3 : 2011

EN 61000-6-1 : 2007

and is certified to be compliant

Specification EC/EMC/KI/KMIRP2 details

the specific test configuration, performance

and conditions of use.

Please Note:

Batteries used in this instrument should be disposed of in accordance with current legislation

and local guidelines.

At the end of the product's life it should be re-cycled in accordance with current legislation

and local guidelines.

Inhaltsverzeichnis

Andere Kane Drucker Handbücher

Kane

Kane KMIRP Bedienungsanleitung

Beliebte Drucker Handbücher anderer Marken

Lexmark

Lexmark 1400 Series Handbuch

Canon

Canon i70 Series Bedienungsanleitung

Evolis

Evolis Elypso Bedienungsanleitung

Kyocera

Kyocera FS-9530DN Bedienungsanleitung

Canon

Canon LASER SHOT LBP-1210 Bedienungsanleitung

Samsung

Samsung BIXOLON SRP-350plusF Bedienungsanleitung

Canon

Canon PIXMA PRO-1 Series Bedienungsanleitung

Canon

Canon PIXMA G3560 Einrichtungshandbuch

Dell

Dell Color Laser Printer 2130cn Bedienungsanleitung

Tektronix

Tektronix Phaser 840 Bedienungsanleitung

Epson

Epson ET-7750 Betriebsanleitung

Canon

Canon CLBR 460ps Bedienungsanleitung

Eltron

Eltron P210 Guide Bedienungsanleitung

Ricoh

Ricoh MD-P1 Bedienungsanleitung

Epson

Epson SC-F7100 series Bedienungsanleitung

Epson

Epson Stylus C40UX Bedienungsanleitung

Canon

Canon imagePASS-A2 Bedienungsanleitung

Canon

Canon S820D Bedienungsanleitung