Kappa WST-916 Bedienungsanleitung
Operation Manual
Model: One gang wireless wall switch with built in timer.
Item No.: WST-916
Overview:
Eco friendly one gang wireless wall switch with built in ‘OFF’ timer.
Nor justsimple manual ON / OFF / Dim functions,itcomes with additional7 selection of delay‘OFF’time.
5s / 30s / 5m / 10m/ 30m/ 1hr / 3hrs
Easyinstallations with either screwfix into current wall box or affix any location with adhesive tape.
Specification:
Installation
1. Screwbase into wall or wall box.
2. Affix frame onto base.
3. Affix rocker onto frame.
Pairing
Pairing using LEARNING MODE:
1. First choose the desired receiver(s) that you wish to control.
2. Press the ‘Learn’ button once (LED will flash), this will now enter learning mode.
3. On the wall switch press the ‘ON’ button; the load will flash twice to confirm that the wall switch is now paired.
！If pairing with CFR-2022& CFR-2027, the rotary dialer must first be positioned in ‘0’ inorder to function correctly.
NOTE: Learning mode lasts for 12 seconds; if no signal is given to the receiver then it will automatically exit learning
mode without pairing the device.
To exit learning mode manually, simply press the ‘Learn’button again.
！If, during learning mode the load does not flash to confirm, this means that the receiver’s memory is FULL and no
further remote control may be paired unless one of the existing remote control is first unpaired (see below).
Un-pairing
Removing single Device:
1. With the receiver that you intent to un-pair press the ‘Learn’button once (LED will flash), this will now enter learning
mode.
2. On the wall switch press the ‘OFF’button; the load will flash twice to confirm that the wall switch is now unpaired.
Product Setup
Manual ‘ON/OFF’ function.
With a screw driver position the rotary dialer to ‘0’ position.
Delay ‘Off’ function.
5secs (more suitable for gate door) / 30secs / 5mins / 10mins / 30mins / 1hr / 3hrs
With a screw driver adjust the rotary dialer to the desired time.
Example: Set at ‘3hr’
1. Switch ‘ON’ the living room load (light).
2. Timer will start the countdown until it reaches 3 hours.
3. After 3 hours, wall switch will automatically send an ‘OFF’ signal to the load (light).
NOTE:
During countdown interval for ON/OFF receiver(s) if;
2nd ‘ON’ button is pressed, the timer will restart countdown from the beginning.
‘OFF’ button is pressed, will turn ‘OFF’ the load (light) and exist the timer countdown.
During countdown interval for Dimmer receiver(s) if;
2nd ‘ON’ button is pressed, the load (light) will start to dim and at the desired brightness level press the ‘ON’ button
again. Note the timer will restart countdown from the beginning.
‘OFF’ button is pressed, will turn ‘OFF’ the load (light) and exist the timer countdown.
Operation
ON/OFF Function:
Press the ‘ON’ button on wall switch, the lights will gradually illuminate.
Press the ‘OFF’ button on wall switch, the light will gradually turn OFF.
Dimming Function:
1. Make sure the load (light) is switched ON.
2. On the wall switch press the ON button again, the loads will start to dim.
3. To stop at the desired brightness level, press the ON button again.
※ Dimming level dims in cycle, during the cycle if no signal is given『with 4 cycles it will stop at 100% brightness』.
！After setting a dim level using the wall switch the light is then switched OFF, the next time that the light is switched back
ON again the load (light) will return to the previous stipulated brightness.
Battery Replacement
3V CR2032 lithium battery is included.
When the battery voltage is low, the transmission range will be reduced accordingly.
1. Press the battery holder.
2. Remove battery.
3. Replace fresh battery making sure ‘＋’ positive terminal is facing up
4. Push battery firmly into battery compartment.
Specification
Frequency: 433.92MHz
Battery: 1 x Lithium battery 3V CR2032
Inhaltsverzeichnis
Andere Kappa Schalten Handbücher
