Kasco Robust-Aire Diffuser Bedienungsanleitung
1
ROBUST-AIRE DIFFUSER
ASSEMBLY INSTRUCTIONS
Robust-Aire Diffuser Assembly
Watch our assembly animation at http://kascomarine /products/diffusers/robust-aire/video
800 Deere Rd. Prescott, WI 54021 •715-262-4488 • sales@kascomarine.com • www.kascomarine.com
2
ROBUST-AIRE DIFFUSER
ASSEMBLY INSTRUCTIONS
An unpacked Robust-Aire Diffuser. Please reference this image throughout assembly for part names.
3
ROBUST-AIRE DIFFUSER
ASSEMBLY INSTRUCTIONS
Suggested Installation Tools & Methods
7/16” socket wrench with shaft extension or 7/16” nut driver
Adjustable Wrench
Flathead screw driver or ¼” Nut Driver
Retrieval ropes longer than the desired installation depth. (Optional)
Marker Buoy (Optional)
Warnings and Suggestions
When installing do not use boats that tip easily, such as a canoe. Follow all boating
safety rules and regulations, including wearing a PFD. (Personal Flotation Device)
Make sure to unroll any rolls of SureSink tubing that have been received before
installing the diffuser. Unrolling the tubing will make it less likely to kink as it is being
taken out with the diffuser to the installation site. Make sure to also unroll and connect
any additional rolls of Suresink before going to the installation site.
Using a retrieval rope coupled with a buoy will allow for easy retrieval of the unit if
maintenance is ever needed or the need to move the diffuser arises.
4
ROBUST-AIRE DIFFUSER
ASSEMBLY INSTRUCTIONS
Assembly Instructions
Note: When finished
assembling your diffuser
you will be left with the
parts needed for either
the 3/8” or 5/8”
SureSink tubing. These
are included in the kit as
user SureSink size is
unknown at the time of
making the product.
Step 1: After unpacking
your box, the tubing
assembly tee’s open
end will be turned
towards the center of
the loop. Twist the tee
fitting so the open end
will face away from the
center of the tubing
loop.
5
ROBUST-AIRE DIFFUSER
ASSEMBLY INSTRUCTIONS
Step 2: Assemble both
Tubing Assemblies to
the Inlet Check Valve
assembly.
Tighten until snug
making sure blue line on
both aeration tubing
assemblies face the
same direction and are
parallel with the Inlet
Check Valve Assembly.
Tighten a barbed fitting
into the check valve
assembly. Choosing a
barbed fitting depends
on the customers
SureSink tubing size.
Use an adjustable
wrench to tighten the
barbed fitting to the
Inlet Check Valve
Assembly.
Step 3: With the blue
line on the tubing facing
down, attach substrate
riser around tee fitting.
Rotate up and secure
aeration tubing into
substrate riser.
6
ROBUST-AIRE DIFFUSER
ASSEMBLY INSTRUCTIONS
Step 4: Repeat step 3 to
attach both substrate
risers to the assembly.
Note: For best
performance, adjust
tubing to have equal
amount of tubing on
either side of substrate
risers.
Step 5: Take the
Substrate Connector
Plate and the Substrate
Edge Guards and slide
the guards onto the
connector as shown.
7
ROBUST-AIRE DIFFUSER
ASSEMBLY INSTRUCTIONS
Step 6: Rotate the
entire assembly and set
the tubes on a flat
surface.
Next take your
substrate edge guards
and substrate connector
plate and set on top of
the assembly as shown.
Step 7: Insert the six
provided carriage bolts
into the holes on the
substrate connector
plate and loosely
tighten them down with
the six provided lock
nuts to temporarily hold
them in place.
8
ROBUST-AIRE DIFFUSER
ASSEMBLY INSTRUCTIONS
Step 8: Flip the diffuser
assembly back over and
tighten down each nut
until snug with a socket
wrench or a 7/16” nut
driver.
An extender for the
socket wrench is
recommended.
9
ROBUST-AIRE DIFFUSER
ASSEMBLY INSTRUCTIONS
Step 8 completed
Step 9: Slide the
provided hose clamp
onto the SureSink
tubing. Hose clamp size
depends on the user’s
SureSink Size. Feed the
weighted tubing over
substrate connector
leaving plenty of slack,
make a generous loop
and secure tubing to
barbed fitting with the
hose clamp.
Tighten down clamp
with a flathead
screwdriver or a ¼” nut
driver.
10
ROBUST-AIRE DIFFUSER
ASSEMBLY INSTRUCTIONS
Step 10: Press weighted
tubing into strain relief
features on both sides
of the connector plate,
being sure tubing loop
isn’t too tight to cause
strain on barbed fitting.
Strain relief features are
designed to
accommodate both
3/8” and 5/8” SureSink
tubing.
Step 11: The SureSink
strain reliefs run
diagonally through the
substrate connector
plate. Make sure to
press the Sure Sink into
both correctly sized
holes before installing
the unit.
Inhaltsverzeichnis
Andere Kasco Rasen- und Gartengeräte Handbücher
Kasco
Kasco 1812AF Bedienungsanleitung
Kasco
Kasco 2400EVFX Handbuch
Kasco
Kasco Robust-Aire RA1-PM Bedienungsanleitung
Kasco
Kasco 8400EA Handbuch
Kasco
Kasco 8400JF Bedienungsanleitung
Kasco
Kasco 2400A Handbuch
Kasco
Kasco 8400A Handbuch
Kasco
Kasco 3.1EVFX Handbuch
Kasco
Kasco Robust-Aire Bedienungsanleitung
Kasco
Kasco VFX Series Bedienungsanleitung
Beliebte Rasen- und Gartengeräte Handbücher anderer Marken
Vertex
Vertex 1/3 HP Technische Daten
GHE
GHE AeroFlo 80 Bedienungsanleitung
Millcreek
Millcreek 406 Bedienungsanleitung
Land Pride
Land Pride Post Hole Diggers HD25 Bedienungsanleitung
extraspace
extraspace GardenStore Bedienungsanleitung
Yazoo/Kees
Yazoo/Kees Z9 Commercial Collection System Z9A Programmierhandbuch
