KaVo EWL 5407 Bedienungsanleitung
Operating Instructions
Flask Press EWL 5407
1.001.3275 ●RB ●12/01 GB 15.09
ZU
AUF
KaVo Elektrotechnisches Werk GmbH
Wangener Straße 78
D-88299 Leutkirch
Tel.: 0 75 61 / 86-0 •Fax: 0 75 61 / 86-22 2
1.000.8796
EWL 5407 1
GB
TABLE OF CONTENTS
A 1 Features ........................................................................................................................................................2
A 2 For your safety ............................................................................................................................................2
A 2.1 Observance of the Operating Instructions ............................................................................................2
A 2.2 Safety considerations ..........................................................................................................................2
A 2.3 Liability for function and damage ........................................................................................................2
A 3 Applications ................................................................................................................................................2
A 4 Preparing for installation ............................................................................................................................3
A 4.1 Unpacking / Transport ........................................................................................................................3
A 4.2 Installation / Storage ............................................................................................................................3
A 5 Preparing for operation ..............................................................................................................................3
A 6 Operating the unit ........................................................................................................................................4
A 7 Troubleshooting ..........................................................................................................................................4
A 8 Care of the unit ............................................................................................................................................5
A 8.1 Cleaning ..............................................................................................................................................5
A 8.2 Maintenance ........................................................................................................................................5
A 8.3 Accessories ..........................................................................................................................................5
A 8.4 Repairs ................................................................................................................................................5
A 9 Technical Data ..............................................................................................................................................6
A 9.1 Flask Press for 1 –3 Flasks ................................................................................................................6
Warranty information ......................................................................................................................................6
Spare parts ....................................................................................................................................................7
2EWL 5407
A 1 Features
Flask Press EWL 5407 is designed to compress flasks, both individuall and appropriate to the material, b means of a smooth build-up of
the working pressure to 6 metric tons.
After completion of the procedure, Flask Press EWL 5407 is immediatel read for further operation, as the reinforced s nthetic-resin
pressure piston automaticall retracts after opening the valve. A high-qualit manometer submerged in the housing to prevent
contamination, precisel reproduces the generated pressure.
In addition to the rust-free s nthetic pressure piston, the lifetime of the press is enhanced b the construction of drawn steel (no danger of
breaking) and the robust resin-coated housing.
A distance of 152 mm between the pillars ensures that the press is also suitable for larger flasks and flask clamps.
A 2 For your safety
A 2.1 Observance of the Operating Instructions
Each user of the unit is assumed to have a thorough knowledge and observance of these operating instructions. The unit is designed onl
for the applications described. In these operating instructions, particularly important comments are illustrated as follows:
Warning! This is a warning relating to risk and dangerous situations. Non-compliance with this warning can lead to life-
threatening situations. These warnings must be strictl observed.
Information! This is information relating to specific characteristics to be observed.
A 2.2 Safety considerations
None
A 2.3 Liability for function and damage
If the unit is improperl maintained, repaired, or altered b an unqualified person; or is used for purposes for which it was not designed,
then the responsibilit for proper function is solel carried b the owner or operator of the unit.
The unit must be maintained and operated in accordance with these operating instructions.
KaVo EWL is not liable for damage arising as a result of non-compliance with the above information.
Guarantee and liabilit conditions as described in the Sales and Deliver Conditions from KaVo EWL are not extended through the above
information.
Ensure that these operating instructions are available at all times, are read, and understood.
A 3 Applications
The h draulic press is designed to compress flasks, both individuall and appropriate to the material, b means of a smooth build-up of the
working pressure to 6 metric tons.
GB
OPERATING INSTRUCTIONS
EWL 5407 3
A 4 Preparing for installation
A 4.1 Unpacking / Transport
Remove all packing materials, and set the unit on a firm and flat surface.
Check the included accessories (see A 8.3)
When shipping the unit, pack it in a suitable container to prevent transport damage.
A 4.2 Installation / Storage
Before use, the press must have reached room temperature.
Set the unit on its final place, horizontall level.
Ensure that the working and operating areas are not cramped (observe unit dimensions).
Do not set up outside!
For long-term storage, protect the unit against dampness and dust.
A 5 Preparing for operation
To ensure an even distribution of pressure, centre the flask on the pressure piston.
Wind the spindle down onto the flask.
The usual pressure required lies between 2,5 and 5 metric tons. This area is coloured green on the manometer. In order to prevent
damage to flasks and the press, do not pump be ond the maximum indicated on the manometer.
4EWL 5407
A 6 Operating the unit
All recommendations for the applications of the unit, whether oral, written or in the form of practical instructions, are based on our
own experience and tests and can, therefore, onl be considered as guidelines.
1. Prepare the flask – see A 5
2. Close the pressure valve b turning the black knob at the front of the housing to “ZU”
3. Operate the pump handle to build up the pressure – do not go be ond maximum!
Green area in manometer
4. Pause occasionall and, if necessar , continue pumping – observe maximum pressure!
5. When the screws on the flask clamp are tight and the pressure remains constant, it can be released b opening the pressure valve.
6. Wind the spindle up and remove the flask.
• While the acr lic is being distributed under pressure, the indicator will fall.
• Therefore, a complete pressing can onl be achieved b pumping several times, with appropriate pauses. When the flask is completel
closed, the pressure remains constant.
• A built-in return spring automaticall retracts the pressure piston to its zero position.
• The piston-stroke is approx. 12 mm.
• When this height is reached, an automatic piston-height limitation opens, and pressure can no longer be produced.
The oil level must be constantl checked when the pressure piston is retracted. Fill with oil if necessar . To do this, remove the
ventilation screw (oil fill duct) located on the housing behind the left pillar. No damage will occur if too much oil is put in, as the
surplus will flow out of the duct. Onl use h draulic oil 0.489.2007!
A 7 Troubleshooting
Problem Possible cause Possible remedy
Pressure does not build up, or Oil level was below minimum Ventilate the press as
onl limited pressure is reached. and during filling, air got into described below.
the s stem
Despite closed flask, pressure Pressure valve contaminated Vigorous pumping, after
falls to zero, or pump plunger replacing with correct oil
rises under pressure.
Ventilation instructions
1. Tilt the press to the right, and then pump.
2. No success? - then remove the pump plunger as follows, and fill with oil to the upper edge of the guide sleeve.
- Loosen the threaded pin in the U-piece.
- Pull out the pump handle.
- Pull the pump plunger up out of the guide sleeve.
- Fill with EWL h draulic oil 0.489.2007.
- Re-assembl follows in reverse order, whereb two points must be observed:
a) Do not cant the pump plunger
b) Take care not to damage the quad ring.
If the above measures do not solve the problem, contact our local Dealer or our Technical Customer Service.
GB
OPERATING INSTRUCTIONS
EWL 5407 5
A 8 Care of the unit
A 8.1 Cleaning
In order to ensure trouble-free operation, the unit should be cleaned at regular intervals, using a mild detergent with a sponge or soft cloth.
Do not use an chemicals. The freel -visible piston track should be cleaned dail with a clean linen cloth, then lightl lubricated with the
recommended h draulic oil.
The nameplate must alwa s be legible, and never be removed.
A 8.2 Maintenance
The KaVo EWL Flask Press requires no special maintenance. Simpl ensure that the unit is alwa s clean.
A 8.3 Accessories
Mat. No. Description
1.001.2187 Stainless steel Clamp for 3 flasks (not included)
1.001.2188 Stainless steel Clamp for 2 flasks (not included)
1.001.2189 Stainless steel Clamp for 1 flask (not included)
0.626.0010 Flasks
A 8.4 Repairs
Service or repairs of the unit must be carried out onl b trained technical personnel.
Modifications b others, and use of unauthorized parts, invalidates the Product Liabilit .
Use onl original spare parts.
6EWL 5407
A 9 Technical Data
A 9.1 Flask Press for 1 – 3 Flasks
Working pressure: Up to 6 metric tons
Recommended oil: EWL H draulic Oil 0.489.2007
Pressure piston: Surface diameter 95 mm.
Working area: Width between pillars 152 mm.
Height min. 42 mm
Height max. 212 mm. (distance between pressure piston and
spindle plate)
Overall dimensions: Width 200 mm.
Depth 158 mm.
Depth with pump handle 295 mm.
Weight: 14.7 Kg
Technical modifications reserved.
Warranty information
Within the scope of the current Deliver and Pa ment Conditions, KaVo EWL warrants the unit to be free from malfunctions, defects in
both materials and workmanship for a period of 6 months from the date of purchase. At the end of this warrant period, KaVo provides a
further 6-months guarantee for faults arising, which can be traced back to deficiencies in materials or the manufacturing process.
For established complaints, the guarantee covers onl the suppl or repair of replacements, free of charge. KaVo EWL is not liable for
defects, and their consequences, caused b or which could be caused b normal wear; misuse; improper cleaning or maintenance; failure to
follow the operating, maintenance or electrical regulations; corrosion; air pollution; chemical or electrical influences which are unusual, or
not in accordance with factor regulations.
The guarantee does not appl if defects, or consequential damage, are the result of unauthorized modifications, and alterations to the
product. Entitlement to the guarantee can onl be validated if claims are submitted without dela , in writing.
Return of the product must be accompanied b a cop of the invoice or deliver note, on which the serial number is clearl indicated.
SPARE PARTS GB EWL 5407
EWL 5407 7
Spare parts
1.001.2168
1.001.2169
1.001.2182
1.001.2181
1.001.2170
EWL Hydraulic Oil 0.489.2007
1.001.2200
1.001.2198
1.001.2199
1.001.2200
1.001.2201
1.001.2204
1.001.3423
Inhaltsverzeichnis
Andere KaVo Elektrowerkzeuge Handbücher
