KB Electronics KBWS-12 Bedienungsanleitung

INSTALLATION AND OPERATING INSTRUCTIONS

KBWS WHISPER DRIVE

PULSE WIDTH MODULATED (PWM)

See Safety Warnin on Pa e 5 before

installin and operatin this control

The information contained

in this manual is intended to be accurate.

However, the manufacturer retains

the right to make changes in design

which may not be included herein.

DC Motor Speed Control with Built-In

Input Si nal Isolation

See Table 1 on page 10 for a list of KBWS

Models covered by this manual

Hi-Pot

Tested

1500 VAC

Note: A PLu -In Horsepower Resistor®

must be installed for this product to

operate (supplied separately).

TABLE OF CONTENTS

Section Pa e

i. Simplified Operating Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

ii. Safety Warning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

I. Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

II. Plug-In Horsepower Resistor® . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

III. Wiring Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

IV. Setting Selectable Jumper (On Dual Voltage Models) . . . . . . . . . . . . . . . . . . . 15

V. Mounting Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

VI. Recommended High Voltage Dielectric Withstand Testing (Hi-Pot Testing) . . . . 16

VII. Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

VIII. AC Line Fusing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

IX. Trimpot Adjustments . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

X. Diagnostic LEDs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

XI. Optional Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

XII. Limited Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

Tables

1. Electrical Ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

2. General Performance Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

3. Plug-In Horsepower Resistor®Selection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

4. Recommended AC Line Fuse . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

Fi ures Pa es

1. Control Layout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

2A. Mechanical Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

2B. Mechanical Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

3. Plug-In Horsepower Resistor®. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

4. Power Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

5. Main Speed Potentiometer Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

6. Voltage Following Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

7. Inhibit Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

8. Enable Circuit Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

9. Motor Voltage Selection (J1) (Dual Voltage Models) . . . . . . . . . . . . . . . . . . . . . 15

10. Hi-Pot Test Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

11. Maximum Speed Trimpot (MAX) Range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

12. Minimum Speed Trimpot (MIN) Range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

13. Acceleration Trimpot (ACC) Range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

14. Deceleration Trimpot (DEC) Range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

15. Current Limit Trimpot (CL) Range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

16. IR Compensation Trimpot (IR) Range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

iii

i. SIMPLIFIED OPERATING INSTRUCTIONS

IMPORTANT – You must read these simplified operating instructions before proceed-

ing. These instructions are to be used as a reference only and are not intended to

replace the detailed instructions provided herein. You must read the Safety Warning

on page 5 before proceeding. See Application Note, Section VII, on page 18.

A. Power Connection – Connect the AC line to L1 and L2 terminals, as shown in

Figure 4, on page 13 and as described in Section IIIA, on page 13.

B. Permanent Ma net (PM) Motor Connection (Two Wire Type) – Connect the

motor armature to terminals A+ and A- as shown in Figure 4, on page 13 and as

described in Section IIIB, on page 13. On dual voltage models, be sure that

Jumper J1 is set to the corresponding motor voltage position, as described in

Section IV, on page 15.

C. Plu -In Horsepower Resistor® – Install the proper Plug-In Horsepower

Resistor®(supplied separately) according to motor current and horsepower.

See Table 3, on page 12.

D. Trimpot Settin s – All trimpots have been factory set, as shown in Figure 1, on

page 8. Trimpots may be readjusted, as described in Section IX, on page 18.

E. Dia nostic LEDs – After power has been applied, observe the LEDs to verify

proper control function, as described in Section X, on page 22.

This product complies with all CE directives pertinent at the time of manufac-

ture. Contact the Sales Department for detailed installation and Declaration of

Conformity. Installation of a CE approved RFI filter (KBRF-300 [P/N 9484] or equiva-

lent) is required. Additional shielded motor cable and/or AC line cables may also be

required.

ii. SAFETY WARNING! Please read carefully

This product should be installed and serviced by a qualified technician, electrician,

or electrical maintenance person familiar with its operation and the hazards involved.

Proper installation, which includes wiring, mounting in proper enclosure, fusing or other

over current protection, and grounding can reduce the chance of electrical shocks,

fires, or explosion in this product or products used with this product, such as electric

motors, switches, coils, solenoids, and/or relays. Eye protection must be worn and

insulated adjustment tools must be used when working with control under power. This

product is constructed of materials (plastics, metals, carbon, silicon, etc.) which may

be a potential hazard. Proper shielding, grounding and filtering of this product can

reduce the emission of radio frequency interference (RFI) which may adversely affect

sensitive electronic equipment. If further information is required on this product, con-

tact the Sales Department.

This control contains electronic Start/Stop circuits that can be used to start and

stop the control. However these circuits are never to be used as safety disconnects

since they are not fail-safe. Use only the AC line for this purpose.

Be sure to follow all instructions carefully. Fire and/or electrocution can result due

to improper use of this product.

This control does not contain protection circuitry to prevent full speed runaway in

the event of main power transistor failure. However, an optional Product Safety

Module (PSM) (P/N 9995) can be installed to prevent full speed runaway. If a PSM is

not used, the installer of this product should take proper precautions to include other

means, such as mechanical disconnects, warning notices, etc., to protect the operator

of the machine involved.

It is the responsibility of the equipment manufacturer and individual installer to sup-

ply this Safety Warning to the ultimate end user of this product. (SW effective 1/2001).

I. INTRODUCTION

Thank you for purchasing the KBWS. KB Electronics, Inc. is committed to providing

total customer satisfaction by producing quality products that are easy to install and

operate. The KBWS is manufactured with surface mount components incorporating

advanced circuitry and technology.

The KBWS PWM (pulse width modulated) controls are designed to operate PWM

and SCR rated Permanent Magnet motors ranging from 1/50 HP to 11⁄2HP. They

operate at a switching frequency greater than 16 kHz to provide high motor efficien-

cy and quiet operation. Another advantage of PWM is higher output voltage (up to

130 Volts DC for 115 Volt AC line and 220 Volts DC for 208/230 Volt AC line) which

provides increased motor speed.

The KBWS contains pulse-by-pulse current sensing, which provides short circuit

protection and prevents control damage due to commutator arcing. Permanent

magnet motor demagnetization is completely eliminated because current peaks are

reduced to safe levels. The controls contain anAC inrush current limiter (ICL) which

reduces the AC line surge current during cycling of the AC line.

Standard features of the KBWS include diagnostic LEDs for Power On and Current

Limit indication. Other features include adjustable trimpots for maximum speed,

minimum speed, acceleration, deceleration, current limit and IR compensation. Also

provided is a connector for an Inhibit Switch and quick-connect terminals forAC line,

motor armature and Main Speed Potentiometer. The KBWS can be operated from

a two wire start/stop circuit or can be started from the AC line.

Due to its user-friendly design, the KBWS can be easily tailored to specific applica-

tions. See Table 1 on page 10, for electrical ratings. The Plug-In Horsepower

Resistor®matches the motor characteristics to the control without having to recali-

brate the Current Limit (CL) and IR Compensation (IR) trimpots. Therefore, for most

applications, no adjustments are necessary.

The KBWS contains built-in isolation for all signal inputs. This includes input signal

voltage, Main Speed Potentiometer terminals, Inhibit Circuit and +5VDC power sup-

ply. The dual voltage models contain a jumper to select motor voltage and special

circuitry which automatically accepts AC Line input voltages of 115 or 208/230 Volts

AC without having to make a jumper selection. See Application Note, Section VII,

on page 18.

Optional accessories for the KBWS include a DIN Rail Mounting Kit, a Product

Safety Module (PSM) and an AC Line Fuse Kit. See Section XI, on page 23.

STANDARD FEATURES

A. Plu -In Horsepower Resistor® – Automatically calibrates IR Compensation and

Current Limit.

B. Dia nostic LEDs – Power On (PWR ON) and Current Limit (CL).

C. Short Circuit Protection – Protects the control from a short circuit at the motor.

D. Isolated Si nal Input Circuit – Eliminates the need for an external signal isolator.

E. Protection Features – Undervoltage protection. MOV input transient protection.

AC Inrush current limit protection.

F. Inhibit Circuit – Provides electronic coast-to-stop.

G. Auto AC Line Select – Control automatically adjusts for 115 or 208/230 VoltAC line

input (dual voltage models).

H. Motor Volta e Selection – Allows motor voltage to be set to 90/130 or 180 Volts DC

(dual voltage models).

Plug-In

Horsepower

Resistor®

(Supplied Separately)

KBWS

180V 90V

A+A-

PWR ON

P3 P2 P1

CON1

IRCLDECMIN ACCMAX

FIGURE 1 – CONTROL LAYOUT

(Illustrates Factory Setting of Jumpers and Approximate Trimpot Settings)

KBWS

180V 90V

A+A-

PWR ON

P3 P2 P1

CON1

IRCLDECMIN ACC

MAX

2.98

[75.8]

1.23

[31.4]

0.48

[12.3]

4.30

[109.2]

3.62

[92.1]

3.80

[96.5]

FIGURE 2A – MECHANICAL SPECIFICATIONS (Inches / [mm])

[55.5]

2.19

[50.5]

1.99

2.19

[55.5]

KBWS-12:

KBWS-15:

KBWS-22D:

KBWS-25D:

8 PLACES

Ø0.19

[Ø4.83]

3.17

[80.5]

1.25

[31.8]0.95

[24.1]

3.80

96.5

FIGURE 2B – MECHANICAL SPECIFICATIONS (Inches / [mm])

PWM Rated

Motors

1/3, (0.25)

Maximum Horsepower

Ratin HP, (kW)

SCR Rated

Motors

Model Part

No.

AC Line Input Volta e

(±10%, 50/60 Hz)

(Sin le Phase Volts AC)

Motor

Volta e

(Volts DC)

Maximum

AC Line

Current

(Amps AC)

Maximum

Load

Current

(Amps DC)

KBWS-12

KBWS-15

KBWS-22D*

KBWS-25D*

3/4, (0.5)

9490

9491

9492

9493

115

208/230

115

208/230

0 - 90, 130

0 - 180, 220

0 - 90, 130

0 - 180, 220

4.0

3/4, (0.5)

8.0

4.0

8.0

2.5

5.0

2.5

5.0

1/4, (0.18)

1/2, (0.37)

1/4, (0.18)

1/2, (0.37)

1/4, (0.18)

1/2, (0.37)

1, (0.75)

1/2, (0.37)

3/4, (0.5)

1/3, (0.25)

3/4, (0.5)

1/3, (0.25)

11⁄2, (1)

TABLE 1 – ELECTRICAL RATING

* See Sections 1G and 1H on page 7.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere KB Electronics Gleichstromantrieb Handbücher

KB Electronics

KB Electronics Penta Power KBRG-212D Bedienungsanleitung

KB Electronics

KB Electronics Penta Power KBVF Series Bedienungsanleitung

KB Electronics

KB Electronics KBPC-240D Konfigurationshandbuch

KB Electronics

KB Electronics Penta Power KBRG-255 Bedienungsanleitung

KB Electronics

KB Electronics Penta Power KBRG-212D Bedienungsanleitung

KB Electronics

KB Electronics KBBC Series Bedienungsanleitung

KB Electronics

KB Electronics PENTA KB POWER KBRG-225D Bedienungsanleitung

KB Electronics

KB Electronics KBAC-24D Bedienungsanleitung

Beliebte Gleichstromantrieb Handbücher anderer Marken

Vincent Associates

Vincent Associates UNIBLITZ ED12DSS Bedienungsanleitung

EKSMA OPTICS

EKSMA OPTICS DQ-100-4 Stücklistenhandbuch

Chamberlain Garog

Chamberlain Garog D Series Bedienungsanleitung

Parker

Parker PDS Series Bedienungsanleitung

Festo

Festo DGC G Series Einrichtungshandbuch

Binks

Binks QS-5012-1-CE Bedienungsanleitung

Danfoss

Danfoss VLT 2800 Series Technisches Datenblatt

ABB

ABB ACQ580-01 Series Installationshandbuch

YASKAWA

YASKAWA CANopen SI-S3 Bedienungsanleitung

GE D20A6 Bedienungsanleitung

Unex

Unex MC-D-250-1000-050W-TW Bedienungsanleitung

Geckodrive

Geckodrive G213V Bedienungsanleitung

ABB

ABB RSYC-01 Bedienungsanleitung

Rockwell Automation

Rockwell Automation PowerFlex 700S Betriebsanleitung

WEG

WEG DeviceNet CFW500 Bedienungsanleitung

Siemens

Siemens SINAMICS G Datenblatt

Siemens

Siemens SINAMICS SM150 6SL3815-7NP41-0AA1 Betriebsanleitung

SOMFY

SOMFY JR RU 30 Bedienungsanleitung