KCodes 6 Series Bedienungsanleitung

KCodes 6 Series USB 2.0 / 3.0 Device Server

User’s Manual

Chapter 1 Introduction

Thank you for purchasing 601/601n/611/612/612ac/604n USB Device Server (in the following referred to as

“Server”). This Server is designed to connect your Multifunction Printer, Scanner, Fax, Multifunction Printer,

Hard Drive, iPhone, iPod, USB Digital TV Tuner, Digital Camera, USB Webcam, USB Speaker, USB CD, USB DVD

to your network, allowing all network users’ access to these shared USB devices.

1.1 About 6 Models Described in this Manual

This manual provides introductory information as well as detailed instructions on how to set up and

manage 6 Series in various network environments. The following table shows the differences among the

3 models. All 3 models have a 10/100 Mbit/sec LAN port. However, 601 and 601n has only one USB port,

while 604n v2 have four USB ports. Compared with 3 models have an additional wireless module

(802.11b/g/n). Except for the wireless configuration, most configuration and operations are the same for

601 and 601n/ 604n. Similarly, almost all of the configuration and operations are the same for these

models except that only one USB device can be connected to 601/601n while at most four USB devices

can be connected to 604n. Unless explicitly specified, all instructions in the manual apply to 6 Series.

Model Name

LAN

Wireless

USB Port 2.0(s)

601

Yes

601n

Yes

604n

Yes

And USB 3.0 models have a 10-BaseT /100BASE-TX /1000Base-T RJ-45,USB 3.0 Hi-Speed Type-A. However,

611 has only one USB port, while both 612 and 612ac have two USB ports.

Model Name

LAN

Wireless

USB Port 3.0(s)

611

Yes

612

Yes

612ac

Yes

To fully benefit from this document, you should be familiar with basic networking principles. The

instructions described in this manual are based on the settings in a new Server. To reload the Factory

Parameters, you can reset this Server back to Factory Default, which will restore most of the settings. For

details, please refer to the chapter “Restore Factory Defaults”.

1.2 Customer Support

Should you require any technical assistance, please contact your product reseller. Or you can visit our

website for latest product information. This document is subject to changes without prior notice.

Chapter 2 Product Overview

2.1 Package Contents

Verify that nothing is missing from the package by using the checking list below. Please contact your

dealer if anything is missing or damaged. All packing materials are recyclable. Please confirm the items in

the package below:

This Server (601/601n/604n/611/612/612ac)

CD (Control Center and User’s Manual and Quick Installation Guide)

Power Adaptor

2.2 Product CD

This CD provides easy-to-use Control Center software, and the User’s Manual and Quick Installation

Guide.

2.2.1. Start-up Procedures

If your computer is configured to auto start CDs, this CD will start automatically when inserted. You can

also navigate to the CD and start the autorun.exe file from within the Windows file manager.

2.3 Physical Description

1. Power Adaptor Connector : 5V/1A (for 601 /601n ) or 12V/2A (for 604n) or 5V/3A (for

611/612/612ac)

2. Init Button : for restoring the configurable parameters to the default values

3. Wireless Station

for 601n/604n : IEEE 802.11 b/g/n wireless station with antenna

for 612ac : IEEE 802.11n wireless station with antenna

4. Ethernet Connector : connected to a twisted pair category 5 cable

5. USB Host Ports:

For 601/601n/604n: USB 1.1/2.0 low, full, and Hi-Speed compliant

For 611/612/612ac: USB 1.1/2.0/3.0 low, full, and Hi-Speed compliant

6. Indicators

For 6 Series

Power Indicator is lit while power is applied. If it is not lit, or if it blinks, there is a problem with the

USB device server or Power Adapter.

USB Indicator (one for 601/601n/611, two for 612/612ac, four for 604n v2) is lit while a USB device

connects to a USB Port of the USB device server. If it is not lit, there is a problem with the USB

device or the USB device server.

For 601 v2/611/612

Link Status is lit while network is applied. If it is not lit, it indicates that this server does not connect

to the network.

Status Indicator blinks to indicate network activity.

For 601n v2/604n v2/612ac

LAN Indicator blinks to indicate wired network activity. If it is lit, it indicates the wired network is

applied. If it is not lit, it indicates that the server does not connect to the wired network.

WLAN Indicator blinks to indicate wireless network activity. If it is lit, it indicates the wireless

network is applied. If it is not lit, it indicates that the server does not connect to the wireless

network.

2.4 Supported USB Devices

The USB device server supports the following types of USB devices.

USB Printer

USB multifunction printer (MFP/AIO)

USB scanner

USB storage (like USB external HD, flash disk, and digital camera)

USB speaker

USB camera

USB digital TV tuner

USB webcam

USB CD

USB DVD

iPad

iPhone

Chapter 3 Basic Installation

3.1. Connecting the Hardware

1. Make sure that your USB devices are switched off and that the Server’s Power Adapter is

disconnected.

2. Connect the USB devices to the USB ports with the USB cables.

3. Connect the Server to the network with a twisted-pair category 5 cable, 10baseT, 100baseTX and

/1000Base-T RJ-45.

4. Turn on the USB devices and make sure it is ready for use.

5. Connect the Power Adapter to the Server. The power indicator will light up and USB1 and USB2

indicators will flash in turn. (For 601/601n, only USB1 indicator will flash.) When the Link indicator

lights up, the Server is correctly connected to the network. When USB1 and USB2 indicators stop

flashing, the Server starts to work normally.

3.2. Wireless connection

This section only applies to 601n/604n/612.

3.3.1. Preliminary

Before you can access wireless network, wireless parameters should be set correctly. You

have to setup the first wireless parameter set through LAN (wired) connection.

Wireless access can be set as infrastructure (station) mode, which an access need point to

route network messages with the same SSID.

Wireless access can be secured by WEP (64/128), WPA-PSA (TKIP/AES), and WPA2-PSK (AES).

In infrastructure mode, if network administrator wants to change any security related

parameters, 601nv2/604nv2/612 should be changed first, and then access point. If

parameters mismatch causes wireless access is not allowed, you have to modify those

parameters through LAN connection.

In infrastructure mode, the maximal transfer rate is 150 MBits depending on access point’s

capability.

3.3.2. Set Wireless Configuration Using Control Center

1. Install USB Device Server Control Center. It is available in the 601n v2/604n v2 /612 USB Device

Server Product CD.

2. Start USB Device Server Control Center and Auto-searching USB device server window will appear.

If the wireless parameters are not correct or not set yet, you have to use LAN to

access USB Device Server Control Center.

3. If the tool finds USB device servers in your local area network, then you have to select a server

from the server list.

4. Double click the highlighted server (or click the “Configure Server” button) to get the server’s web

pages. Click CONFIG icon.

5. Login with administrator ID (default: admin) and its password (default: admin).

6. Click Wireless icon.

7. In order to join an existing wireless network, you have to set the correct SSID, and the correct

security method with the correct key information.

8. If the wireless network is secured by WEP64 or WEP128, key index and WEP key must be set

correctly.

9. If the wireless network is secured by WPA-PSK or WPA2-PSK, the key formats, shared key and

encryption must be set correctly.

10. Click Submit to save your settings. And the server will reboot.

11. You have now finished the procedure of setting the wireless parameters

After properly configuring the wireless parameters, you can remove the network cable and reboot the

601n/604n. 601n/604n will then connect to your wireless network. 601n/604n will detect if a network

cable is plugged-in or not. If a network cable is plugged-in, 601n/604n will always connect to the network

through the network cable. Otherwise it will always connect to the network through wireless module.

Once 601n v2/604n v2 /612 connects to the network, either by network cable or by wireless module, all

operations to use USB device server are exactly the same.

3.3. Assigning an IP Address to the Server

3.3.1. Preliminary

If you have a DHCP server on your network, your Server will receive an IP address

automatically. The IP address will then appear on the Control Center or on the page of

configuration report that you printed earlier. If your DHCP server does not give an IP address

to the Server, the Server will use the automatic private IP addressing IP: 169.254.0.0. ~

169.254.255.255

If you are not working in a DHCP network, you need to manually set the Server’s IP address.

3.3.2. IP Address

Unless you are assigning an IP address using DHCP, you must obtain an unused IP address

from your network administrator.

3.3.3. Methods for Setting the IP Address

You can set the IP address of your Server using one of the following methods, depending on your network

operating environment:

Automatic IP Address Assignment

Manual IP Address Assignment

3.3.4. Server Names and Server Name Rules

The default server name of the Server is “KC601” (for 601) or “KC601n” (for 601n) or “KC604n” (for 604n)

or “KC611” (for 611) or “KC612” (for 612) or “KC612ac” (for 612ac). If you put two or more Servers in

your local area network, to avoid using the same server names you have to change the server names by

using the Control Center or the Server’s web pages. If your server name is longer than 15 characters, the

Server uses only the first 15 characters.

3.3.5. Setting the IP Address Using DHCP

Follow the instructions below to get an IP address using DHCP:

1. Edit or create a scope in the DHCP manager of the DHCP daemon. The entries included in this scope

should contain the following parameters:

range of IP addresses

subnet mask

default router IP address

DNS server IP address

lease duration

2. Activate the scope. The Server automatically gets the DHCP parameters. If you are using DNS, you

may include at least one DNS server IP address in the DHCP scope or manually set the DNS server IP

address using Server’s web pages or the Control Center.

3.3.6. Setting the IP Address Using the Control Center

1. Install the Control Center. The Control Center is available on the Product CD.

2. Start the Control Center and Auto-searching Server window will appear.

3. If the tool finds multiple Servers in your local area network, then you have to select one Server from

the Server List.

4. Double click the highlighted server (or click the “Configure Server” button) to get the server’s web

pages. Click CONFIG icon.

5. Login with administrator ID (default: admin) and its password (default: admin).

6. Click the button corresponding to your choice of IP setting methods (static or dynamic using DHCP).

When assigning a static IP address you also have to define Subnet Mask.

7. Click Submit to save your settings. And the Server will reboot. You have now finished the procedure

of setting the IP address.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere KCodes Server Handbücher

KCodes

KCodes 601 Bedienungsanleitung

Beliebte Server Handbücher anderer Marken

HP AlphaServer ES47 Bedienungsanleitung

Dell

Dell PowerEdge R410 Bedienungsanleitung

PowerNAS

PowerNAS CMA Bedienungsanleitung

Supero

Supero FatTwin F617R3-FT Bedienungsanleitung

MSI

MSI P1-109N-L70 Bedienungsanleitung

Dell

Dell PowerEdge XE9640 Handbuch

Dell

Dell PS4100 Montageanleitung

EtroVISION

EtroVISION EV3151 Bedienungsanleitung

NEC

NEC Express5800/T110j Bedienungsanleitung

HP ProLiant Gen9 Bedienungsanleitung

Compaq

Compaq ProLiant 3000 Handbuch

Dell

Dell PowerEdge 3YPMN Bedienungsanleitung

iRobo

iRobo IPC2U Bedienungsanleitung

Nortel

Nortel 1000 Con?guration guide Bedienungsanleitung

Asus

Asus AP7500 Bedienungs- und Wartungshandbuch

Avid Technology

Avid Technology AirSpeed 5000 Bedienungsanleitung

HP Integrity rx2600 Installationsanleitung

Milestone

Milestone Husky IVO 350T Bedienungsanleitung