KEBCO COMBIVERT G6 Bedienungsanleitung

COMBIVERT

Customer parameters v/f operation

Translation of original manual

Document Part version Date

20096630 GBR 00 1214

Table of contents

1. Preface............................................................................................................. 4

1.1 Information on special measures.......................................................................................4

1.2 Documentation.....................................................................................................................4

1.3 Validity and liability .............................................................................................................4

1.4 Copyright..............................................................................................................................5

1.5 Speciedapplication...........................................................................................................6

1.6 Product description.............................................................................................................6

1.6.1 Corresponding documentation...............................................................................................6

2. Parameter Description ................................................................................... 7

2.1 Selection of the customer parameter menu......................................................................7

2.2 Password input in CP mode ...............................................................................................8

2.3 CP-Parameter for open-loop operation .............................................................................9

3. Troubleshooting ........................................................................................... 25

3.1 General ...............................................................................................................................25

3.2 Error Messages and their Cause......................................................................................25

Preface

1. Preface

The described hard- and software are developments of the Karl E. Brinkmann GmbH. The

enclosed documents correspond to conditions valid at printing. Misprint, mistakes and techni-

cal changes reserved.

1.1 Information on special measures

The used pictograms have following signicance:

Danger Is used, when death or serious bodily injury may be the consequence

of non-observance of the measure.

Warning Is used, when bodily injury and/or substantial property damage may

be the consequence of non-observance of the measure.

Caution Is used, when property damage may be the consequence of non-ob-

servance of the measure.

Attention Is used, when noise sensitive or unrequested operation may be the

consequence of non-observance of the measure.

Info Is used, when a better or simpler result can be the consequence of the

measure.

For a special case the instructions can be supplemented by additional pictograms and text.

1.2 Documentation

Before working with the unit the user must become familiar with it. This includes especially

the knowledge and observance of the safety and operating instructions.

Attention Observe safety and operating instructions

Precondition for all further steps is the knowledge and observance of the

safety and operating instructions. This is provided accompanied by the de-

vice or by the download site of www.keb.de.

Non-observance of the safety and operating instructions leads to the loss of any liability

claims. The warnings and safety instructions in this manual work only supplementary. This

list is not exhaustive.

1.3 Validity and liability

The use of our units in the target products is beyond of our control and therefore exclu-

sively the responsibility of the machine manufacturer, system integrator or customer.

The information contained in the technical documentation, as well as any user-specic advice

in spoken and written and through tests, are made to best of our knowledge and information

about the application. However, they are considered for information only without responsibil-

ity. This also applies to any violation of industrial property rights of a third-party.

Preface

Selection of our units in view of their suitability for the intended use must be done generally

by the user.

Tests can only be done within the application by the machine manufacturer. They must

be repeated, even if only parts of hardware, software or the unit adjustment are modi-

ed.

Danger by tamper from unauthorized personnel

Unauthorised opening and tampering may lead to death, bodily injury, prop-

erty damage and malfunctions. Modication or repair is permitted only by

authorized personnel by KEB.. Infringement will annul the liability for result-

ing consequences.

The suspension of liability is especially valid also for operation interruption loss, loss of prot,

data loss or other damages. Disclaimer of warranty will cause void the guarantee. This is also

valid, if we referred rst to the possibility of such damages.

If single regulations should be or become void, invalid or impracticable, the effectivity of all

other regulations or agreements is not affected.

Through multitude applications not each possible case of installation, operation or mainte-

nance can be considered. If you require further information or if special problems occur which

are not treated detailed in the documentation, you can request the necessary information via

the local Karl E.Brinkmann GmbH agency.

1.4 Copyright

The customer may use the instruction manual as well as further documents or parts from it for

internal purposes. Copyrights are with KEB and remain valid in its entirety.

KEB®, COMBIVERT®, COMBICONTROL®and COMBIVIS®are registered trademarks of Karl

E. Brinkmann GmbH.

Other wordmarks or/and logos are trademarks (™) or registered trademarks (®) of their re-

spective owners and are listed in the footnote on the rst occurrence.

When creating our documents we pay attention with the utmost care to the rights of third par-

ties. Should we have not marked a trademark or breach a copyright, please inform us in order

to have the possibility of remedy.

Preface

1.5 Speciedapplication

The COMBIVERT G6 serves exclusively for the control and regulation of three-phase motors.

The operation of other electric consumers is prohibited and can lead to the destruction of the

unit. Frequency inverters are components which are intended for the installation in electric

systems or machines.

The used semiconductors and components of the Karl E.Brinkmann GmbH are developed

and dimensioned for the use in industrial products. If the KEB COMBIVERT G6 is used in

machines, which work under exceptional conditions or if essential functions, life-supporting

measures or an extraordinary safety step must be fullled, the necessary reliability and secu-

rity must be ensured by the machine builder.

The operation of our products outside the indicated limit values of the technical data leads to

the loss of any liability claims.

1.6 Product description

These manual contains the description of the customers parameter of the COMBIVERT G6.

Attention The described parameter are only valid at V/f operation and factory

settings.

1.6.1 Corresponding documentation

Attention Further documentation via www.keb.de

• EMC and safety instructions

• Installation power unit

• Programming Manual

Parameter Description

2. Parameter Description

On delivery the KEB COMBIVERT G6 is assigned with an user menu, the customer parame-

ters (CP-Parameters). These represent a selection of important parameters for the operation.

Up to a maximum of 48 customer parameters can be dened from over 500 parameters.

Only parameter CP00 password input is predened and can not be modied or deleted.

The customer parameter menu described in this manual is valid for open-loop systems. That

can be indentied by parameter CP48 (see below).

2.1 Selection of the customer parameter menu

CP48 Software version

Co-domain Setting Description

0.0.0.0 … F.F.F.F – Display of the software version

The rst two digits display the major and minor version number (e.g.

1.2.x.x => V1.2)

The third digit displays the power unit software

x.x.0.x Power unit open-loop 1st Version (this manual)

x.x.1.x Power unit open-loop 2nd Version (this manual)

x.x.2.x Power unit ASCL →available as Download.

x.x.3.x Power unit SCL →available as Download.

The fourth digit displays a serial number for the date code.

Parameter Description

2.2 Password input in CP mode

CP00 Password input

Ex works the frequency inverter is supplied without password protection, this means that all

changeable parameters can be adjusted. After parameterizing the unit can be barred against

unauthorized access. The adjusted mode is stored. Following password levels are possible:

Password level Val-

Password Explanation

CP mode write protection -1 100 Only reading of customer parameters

CP mode read/write -2 200 Read/write of customer parameters

DezHex

CP00 2800h Satz: 0

Passwort

-1

Passwort:

CP-Mode Schreibschutz

Menü Oben Unten

CP00 Passwort

[0] CP-Mode Schreibschutz

CP01 Istwertanzeige

[0] 50,0000 Hz

CP02 Sollwertanzeige

[0] 50,0000 Hz

CP03 Umrichterstatus

[0] Konstantfahrt Linkslauf

CP04 Scheinstrom

[0] 25,5 A

DezHex

CP00 2800h Satz: 0

Passwort

100

Num

DezHex

CP00 2800h Satz: 0

Passwort

-2

CP-Mode Lesen/Schreiben

Num

Menü Oben Unten

CP00 Passwort

[0] CP-Mode Lesen/Schreib

CP01 Istwertanzeige

[0] 50,0000 Hz

CP02 Sollwertanzeige

[0] 50,0000 Hz

CP03 Umrichterstatus

[0] Konstantfahrt Linkslauf

CP04 Scheinstrom

[0] 25,5 A

DezHex

CP00 2800h Satz: 0

Passwort

-2

Passwort:

CP-Mode Lesen/Schreiben

Info A detailed description of the diplay / keyboard can be found in the pro-

gramming manual "Control circuit analog /digital".

CP-Parameter for open-loop operation

2.3 CP-Parameter for open-loop operation

Parameter Range Resolu-

tion Default Unit Flag based

CP00 Password input 0…9999 1 - - - Ud01

CP01 Actual value display -400…400 0,0125 0 Hz R ru07

CP02 Set frequency display -400…400 0,0125 0 Hz R ru01

CP03 Inverter state 0…255 1 0 - R ru00

CP04 Apparent current 0…6553,5 0,1 0 A R ru15

CP05 Apparent current peak value 0…6553,5 0,1 0 A R ru16

CP06 Actual utilization 0…400 1 0 % R ru13

CP07 Actual DC voltage 0…1000 1 0 V R ru18

CP08 DC link voltage peak value 0…1000 1 0 V R ru19

CP09 Output voltage 0…778 1 0 V R ru20

CP10 min. reference forward 0…400 0,0125 0 Hz - oP06

CP11 max. reference 0…400 0,0125 70 Hz - oP10

CP12 acc. time forward 0,00…300,00 0,01 5 s - oP28

CP13 dec. time forward (-1=CP12) -0,01…300,00 0,01 5 s - oP30

CP14 S-curve time acc. 0,00…5,00 0,01 0 s - oP32

CP15 Boost 0,0…25,5 0,1 LTK % - uF01

CP16 Rated frequency 0…400 0,0125 50 Hz - uF00

CP17 Voltage stabilization 0…649 1 off V E uF09

CP18 Switching frequency 0…LTK 1 LTK - E uF11

CP19 step value 1 -400…400 0,0125 5 Hz - oP21

CP20 step value 2 -400…400 0,0125 50 Hz - oP22

CP21 step value 3 -400…400 0,0125 70 Hz - oP23

CP22 DC braking mode 0…506 1 7 - E Pn28

CP23 DC braking time 0,00…100,00 0,01 10 s - Pn30

CP24 LAD load level 0…200 1 140 % - Pn24

CP25 Stall level 0…200 1 200:off % - Pn20

CP26 Speed search condition 0…31 1 8 - E Pn26

CP27 Motor protect. function response 0…6 1 6 – – Pn14

CP28 Motor protection mode 0…1 1 1 – – dr11

CP29 motorprot. rated current 0,0…370,0 0,1 LTK A – dr12

CP30 ANOUT1 function 0…26 1 2 – E An31

CP31 ANOUT1 gain -20,00…20,00 0,01 1 – – An33

CP32 Condition SB0 0…101 1 20 – E do00

CP33 Condition SB2 0…101 1 4 – E do02

CP34 comparison level 2 ±30000,00 0,01 100,00 – – LE02

CP35 AN1 interface selection 0…2 1 0 – E An00

CP36 select 50Hz/60Hz mode 0…1 1 0 – E Ud06

CP37 warning dOH stop. mode 0…8 1 7 – – Pn12

CP38 Inverter address 0…239 1 0 – – Sy06

CP39 last error 0…255 1 0 – E, R In24

CP40 parameter set copy function -4…7 1 0 – – Fr01

CP48 Software version x.x.x.x – LTK – R In06

LTK=depending on power unit; E=ENTER-Parameter; R=read only

CP-Parameter for open-loop operation

CP00 Password input

see chapter 2.2

CP01 Actual value display

Co-domain Description

0…±400 Hz Display of the actual output frequency in Hz. The rotation of the inverter

is displayed by the sign.

Examples:

18.3 Output frequency 18,3 Hz, rotation forward

-18.3 Output frequency 18,3 Hz, rotation reverse

CP02 Set frequency display

Co-domain Description

0…±400 Hz Display of actually set value. For control reasons the set speed is dis-

played, even if the control release or direction of rotation is not switched.

If no direction of rotation is set, the set frequency for clockwise rotation

(forward) is displayed.

CP03 Inverter state

The actual operating condition of the inverter (e.g. forward constant run, standstill) is dis-

played in parameter „inverter state“. In the case of an error the current error message is dis-

played, even if the display has already been reset with ENTER (status LED is still blinking).

Display State

no operation modulation switched off; output voltage = 0V; drive is not controlled.

no direction of rota-

tion preset

modulation switched off; output voltage = 0V; drive is not controlled.

Acceleration

Forward

drive accelerates with direction of rotation forward.

Deceleration

Forward

drive decelerates with direction of rotation forward.

Acceleration

Reverse

drive accelerates with direction of rotation reverse.

Deceleration

Reverse

drive decelerates with direction of rotation reverse.

Speed dependent

Forward

Drive runs with constant speed and direction of rotation forward.

Speed dependent

Reverse

Drive runs with constant speed and direction of rotation reverse.

Other status messages are described at the parameters, on which they occur (see chapter

„Error Diagnosis“).

Andere Handbücher für COMBIVERT G6

Inhaltsverzeichnis

Andere KEBCO Gleichstromantrieb Handbücher

KEBCO

KEBCO COMBIVERT F5 Series Bedienungsanleitung

KEBCO

KEBCO COMBIVERT F5 Series Merkblatt

KEBCO

KEBCO COMBIVERT F5 Bedienungsanleitung

KEBCO

KEBCO COMBIVERT F5 Bedienungsanleitung

KEBCO

KEBCO COMBIVERT F5 Series Bedienungsanleitung

KEBCO

KEBCO COMBIVERT G6 Bedienungsanleitung

KEBCO

KEBCO COMBIVERT F5 Merkblatt

KEBCO

KEBCO COMBIVERT F4-S Bedienungsanleitung

KEBCO

KEBCO COMBIVERT S4 Bedienungsanleitung

KEBCO

KEBCO COMBIVERT F5 Bedienungsanleitung

KEBCO

KEBCO COMBIVERT F5 Bedienungsanleitung

KEBCO

KEBCO COMBIVERT G6 series Bedienungsanleitung

KEBCO

KEBCO COMBIVERT F0 Bedienungsanleitung

KEBCO

KEBCO COMBIVERT F5 Bedienungsanleitung

KEBCO

KEBCO COMBIVERT F6 series Bedienungsanleitung

KEBCO

KEBCO COMBIVERT F5 Bedienungsanleitung

KEBCO

KEBCO COMBIVERT F4-C Gebrauchsanweisung

KEBCO

KEBCO COMBIVERT F5 Series Bedienungsanleitung

KEBCO

KEBCO COMBIVERT F5 Series Bedienungsanleitung

KEBCO

KEBCO COMBIVERT G6 series Bedienungsanleitung

KEBCO

KEBCO COMBIVERT F5 Bedienungsanleitung

KEBCO

KEBCO COMBIVERT F5 Gebrauchsanweisung

KEBCO

KEBCO COMBIVERT F5 Gebrauchsanweisung

KEBCO

KEBCO COMBIVERT G6 Bedienungsanleitung

Beliebte Gleichstromantrieb Handbücher anderer Marken

Vincent Associates

Vincent Associates UNIBLITZ ED12DSS Bedienungsanleitung

EKSMA OPTICS

EKSMA OPTICS DQ-100-4 Stücklistenhandbuch

Chamberlain Garog

Chamberlain Garog D Series Bedienungsanleitung

Parker

Parker PDS Series Bedienungsanleitung

Festo

Festo DGC G Series Einrichtungshandbuch

Binks

Binks QS-5012-1-CE Bedienungsanleitung

Danfoss

Danfoss VLT 2800 Series Technisches Datenblatt

ABB

ABB ACQ580-01 Series Installationshandbuch

YASKAWA

YASKAWA CANopen SI-S3 Bedienungsanleitung

GE D20A6 Bedienungsanleitung

Unex

Unex MC-D-250-1000-050W-TW Bedienungsanleitung

Geckodrive

Geckodrive G213V Bedienungsanleitung

ABB

ABB RSYC-01 Bedienungsanleitung

Rockwell Automation

Rockwell Automation PowerFlex 700S Betriebsanleitung

WEG

WEG DeviceNet CFW500 Bedienungsanleitung

Siemens

Siemens SINAMICS G Datenblatt

Siemens

Siemens SINAMICS SM150 6SL3815-7NP41-0AA1 Betriebsanleitung

SOMFY

SOMFY JR RU 30 Bedienungsanleitung