KeepGuard KG895 Bedienungsanleitung
This KeepGuard cam is the best-selling scouting camera which is designed for activity and is resistant against water and snow. It
is equipped with built-in infrared sensor, so that it can be triggered accurately by heat sources, then take high quality pictures or
videos. Please refer to the notes below to ensure that you are completely satisfied with this product.
Contents
Highly Recommended by Outdoor Explorers - KeepGuard 4G Wildlife Scouting Cam Instruction Book
1
KEEPTIME
2
3
4
5
6
7
7
8
9-16
17-23
24
25
26
Prepar Before Start Wireless Setting/Quick Start
Notes before use
View Drawings
Camera Overview
Standard Accessories
Power Supply
SD Card
Operational Modes
Settings
Software in APP
Mounting and Positioning
Specification
Warranty Card
Quick Start
2
KEEPTIME
1.Pen and paper: record relevant information
such as APN and ICCID.
2.Mobile phone: the operator's APN
information should be checked in the mobile
phone.
3. 4G SIM card、large card frame、card pin:
check the ICCID number on the card and write
it down, then install the SIM into the camera.
4. Email: for receiving "NETWORK" files.
5. Blank SD card: store "NETWORK" files.
6.Computer: it is used to edit the "NETWORK"
text file and store it on the SD card.
※ Move the latch and open the camera case
※ Load 12 lithium AA(non-rechargeable) or alkaline AA batteries
※ Set "NETWORK" via APP/PC and copy it to SD card
※ Insert the SD card
※ Insert the SIM card
※ Switch to the SETUP Mode,wait about 1Minute
※ Press " UP " key to select Camera or Video Mode
※ Press " MENU " key to setting camera function
※ Press " LEFT" key to take a photo and send it to your APP
※ Switch to the ON Mode
※ Close the case and position the camera for use
Prepar Before Start Wireless Setting
1. When setting camera parameters, please put camera in Setup mode.
2. Do not set the camera directly from ON to Setup.
3. To replace the battery, SD card, and SIM card, firstly turn camera to OFF mode.
4. Color of Indicator
1) When camera is updating firmware, indicator light flashes green.
2) The indicator light flashes red when it is turned on or ready for operation.
3) low battery, the indicator light flashes blue.
4) long standby time, the indicator flashes purple.
5. Batteries need to use dry batteries, do not use rechargeable batteries.
6. When the SD card is inserted into camera, make sure that the SD card is not in lock state.
7. When using an external power supply, make sure that voltage is 12V.
8. Please take out the battery to avoid leakage of the battery if camera is not used for a long time.
9. Camera can not be directly immersed in water, can not be placed in the environment of strong acid and alkali.
10. Don’t use your fingers to press the Fresnel lens.
11. Keep the lens and battery compartment clean.
12. Do not use sharp hard objects to scratch screen.
3
KEEPTIME
Notes Before Use
View Drawings
4
KEEPTIME
Camera Overview
5
KEEPTIME
Standard Accessories
1×Case 1×Manual1×Belt 1×USB
Other Accessories (not included)
1×Micro-Lens
1×Wide-angel Lens
1× Security Case 1×External battery
connection wire
1×solar panel1×Cradle Head
1×5M Antenna
6
KEEPTIME
Power Supply
After opening the latch on the right side of the camera, you will
see that it has 12 battery slots. For maximum battery life, we
recommend using 12 lithium AA or alkaline AA batteries.
Please be sure to insert each battery with correct polarity
(negative or“flat”end against the long spring of each battery
slot).
SD Card / SIM Card
Insert the SD card and SIM card ( Camera being under OFF
mode ) before beginning to operate the camera. SD card is
supported up to maximum 64GB capacity.
SIM
64GB
7
KEEPTIME
Operational Modes
The cam has three basic operational modes: 「OFF」, 「ON」 and 「SETUP」
●「OFF 」Mode
When cam in OFF mode, you can do the following:
• replacing the SD card or batteries
• connecting cam with other device via USB port
●「ON」Mode
Once in ON mode no manual controls are needed or possible (the control keys have no effect). The cam will take photos or videos automatically
(according to its current parameter settings) when it is triggered by the PIR sensor′s detection of activity in the area it covers.
●「SETUP」Mode
In the SETUP mode you can check and change the settings of the cam with the help of built-in LCD. Moving the power switch to the
SETUP position will turn on the LCD display and you will see an information screen.
8
KEEPTIME
Image Resolution of Photos Taken Audio Rec ON Video Resolution
Signal
0000/0888 Video Mode
Available Video
Recording Time
Camera Mode
Time Stamp ON TT
Time Scan ON
SD Card Battery Level
5M 1080P
Settings
Set Clock
9
KEEPTIME
Set Clock
Set
Press OK and use UP/DOWN keys ( to change the setting )
and LEFT/RIGHT keys ( to move to the next field ) to set the
hour ( 24-hr format only, “00”=midnight,“12”=noon)
and minute, and then (on the lower row ),the year,month
and date. Once all settings are made, press OK to save.
OK Set MENU Exit
Mode
Mode
Camera
Video
Dual
Selects whether still photos or video clips are captured when
the camera is triggered. “Dual”=Camera+Video
OK Set MENU Exit
Image Size
Image Size
OK Set MENU Exit
5M
16M
30M
Selects resolution for still photos from 5 to 30 megapixels.
Higher resolution produces better quality photos, but creates
larger files that take up more of the SD card capacity.
Settings
Capture Number
10
KEEPTIME
Capture Number
9
OK Set MENU Exit
Video Size
ze
Video Size
Selects video resolution (in pixels per frame). Higher
resolution produces better quality videos, but creates larger
files that take up more of the SD card capacity (fills up faster).
OK Set MENU Exit
Video Length
Video Length 5s
Sets length per captured video clip. Settings begin with 10
second default when parameter is first selected. After going
down to 5s, video length choice starts over at 60s.
OK Set MENU Exit
Selects how many photos are taken in sequence per trigger
in Camera mode.This setting affects photos taken in Field
Scan mode as well.
640*360
1280*720
1920*1080
Inhaltsverzeichnis
Andere KeepGuard Digitalkamera Handbücher
