KeepRite F96VTN Leitfaden

Installation, Start-up, Operating and

Service and Maintenance Instructions

NOTE: Read the entire instruction manual before starting the installation.

TABLE OF CONTENTS

REQUIRED NOTICE FOR MASSACHUSETTS

INSTALLATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

SAFETY CONSIDERATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

Table 1 – Minimum Clearances to Combustible Materials for All Units

INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Table 2 – Loose Parts Bag . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

CODES AND STANDARDS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

ELECTROSTATIC DISCHARGE (ESD) PRECAUTIONS PROCE-

DURE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

ACCESSORIES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

LOCATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

AIR FOR COMBUSTION AND VENTILATION . . . . . . . . . . . . . . 8

CONDENSATE TRAP. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Table 3 – Minimum Free Area Required for Each Combustion Air

Opening or Duct to Outdoors. . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

Table 4 – Minimum Space Volumes for 100% Combustion, Ventila-

tion and Dilution Air from Outdoors . . . . . . . . . . . . . . . . . . . . . . 10

CONDENSATE DRAIN CONNECTION . . . . . . . . . . . . . . . . . . . . 12

INSTALLATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

Table 5 – Opening Dimensions - In. (mm) . . . . . . . . . . . . . . . . . 17

Table 6 – Air Filter Selection and Duct Sizing - In. (mm) . . . . . 19

Table 7 – Filter Media Pressure Drop (Clean) Versus Airflow - In.

W.C. (Pa) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

Table 8 – Filter Media Pressure Drop (Clean) Versus Face Velocity-

In. W.C. (Pa) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

Table 9 – Cooling4 and Heating Air Delivery - CFM (Bottom Return5

with Filter) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

AIR DUCTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

GAS PIPING. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25

Table 10 – Maximum Capacity of Pipe . . . . . . . . . . . . . . . . . . . . 25

ELECTRICAL CONNECTIONS. . . . . . . . . . . . . . . . . . . . . . . . . . . 26

Table 11 – Electrical Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27

VENTING. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31

Table 12 – Vent Termination Kit for Direct Vent (2-pipe) Systems33

Table 13 – Approved Combustion-Air and Vent Pipe, Fitting and Ce-

ment Materials . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35

Table 14 – Maximum Equivalent Vent Length - Ft. . . . . . . . . . . 42

Table 15 – Deductions from Maximum Equivalent Vent Length - Ft.

(M) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42

Table 16 – Maximum Allowable Exposed Vent Lengths in Uncondi-

tioned Space Insulation Table - Ft. / M . . . . . . . . . . . . . . . . . . . . 44

Table 17 – Hanger Spacing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49

START-UP, ADJUSTMENT, AND SAFETY CHECK . . . . . . . . . 51

Table 18 – Altitude Derate Multiplier for USA. . . . . . . . . . . . . . 54

Table 19 – Blower Off Delay Setup Switch . . . . . . . . . . . . . . . . 56

Table 20 – Orifice Size and Manifold Pressure (In. W.C.) for Gas Input

Rate . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57

Table 21 – Gas Rate (CU ft./hr). . . . . . . . . . . . . . . . . . . . . . . . . . 58

SERVICE AND MAINTENANCE PROCEDURES. . . . . . . . . . . . 58

WINTERIZATION. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65

SEQUENCE OF OPERATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68

PARTS REPLACEMENT INFORMATION GUIDE . . . . . . . . . . . 71

MODEL NOMENCLATURE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71

Most states in the USA and jurisdictions in Canada have laws that

require the use of Carbon Monoxide (CO) alarms with fuel burning

products. Examples of fuel burning products are furnaces, boilers, space

heaters, generators, water heaters, stoves/ranges, clothes dryers,

fireplaces, incinerators, automobiles, and other internal combustion

engines. Even if there are no laws in your jurisdiction requiring a CO

Alarm, it’s highly recommended that whenever any fuel burning product

is used in or around the home or business that the dwelling be equipped

with a CO Alarm(s). The Consumer Product Safety Commission

recommends the use of CO Alarm(s). The CO Alarm(s) must be

installed, operated, and maintained according to the CO Alarm

manufacturer’s instructions. For more information about Carbon

Monoxide, local laws, or to purchase a CO Alarm online, please visit the

following website. https://www.kidde.com.

A200326

Portions of the text and tables are reprinted from NFPA 54/ANSI Z223.1E, with permission of National Fire Protection Association, Quincy, MA

02269 and American Gas Association, Washington DC 20001. This reprinted material is not the complete and official position of the NFPA or ANSI

on the referenced subject, which is represented only by the standard in its entirety.

F96VTN and G96VTN

Two-Stage, Non-Communicating, Variable-Speed ECM, Multipoise, Condensing

Gas Furnace

WARNING

CARBON MONOXIDE POISONING HAZARD

Failure to follow this warning could result in personal injury and/or

death.

Carbon Monoxide (CO) is a colorless, odorless, and tasteless poisonous

gas that can be fatal when inhaled. Follow all installation, maintenance,

and service instructions. See additional information below regarding

the installation of a CO Alarm.

Use of the AHRI Certified TM Mark indicates

a manufacturer's participation in the program.

For verification of certification for individual

products, go to www.ahridirectory.org .

F96VTN and G96VTN: Installation, Start-up, Operating and Service and Maintenance Instructions

Manufacturer reserves the right to change, at any time, specifications and designs without notice and without obligations.

REQUIRED NOTICE FOR MASSACHUSETTS

INSTALLATIONS

IMPORTANT

The Commonwealth of Massachusetts requires compliance with regulation 248 CMR as follows:

5.08: Modifications to NFPA-54, Chapter 10

2) Revise 10.8.3 by adding the following additional requirements:

a. For all side wall horizontally vented gas fueled equipment installed in every dwelling, building or structure used in whole or in part for

residential purposes, including those owned or operated by the Commonwealth and where the side wall exhaust vent termination is less than

seven (7) feet above finished grade in the area of the venting, including but not limited to decks and porches, the following requirements shall

be satisfied:

1. INSTALLATION OF CARBON MONOXIDE DETECTORS. At the time of installation of the side wall horizontal vented gas fueled equipment,

the installing plumber or gasfitter shall observe that a hard wired carbon monoxide detector with an alarm and battery back-up is installed on the

floor level where the gas equipment is to be installed. In addition, the installing plumber or gasfitter shall observe that a battery operated or hard

wired carbon monoxide detector with an alarm is installed on each additional level of the dwelling, building or structure served by the side wall

horizontal vented gas fueled equipment. It shall be the responsibility of the property owner to secure the services of qualified licensed

professionals for the installation of hard wired carbon monoxide detectors

a. In the event that the side wall horizontally vented gas fueled equipment is installed in a crawl space or an attic, the hard wired carbon monoxide

detector with alarm and battery back-up may be installed on the next adjacent floor level.

b. In the event that the requirements of this subdivision can not be met at the time of completion of installation, the owner shall have a period of

thirty (30) days to comply with the above requirements; provided, however, that during said thirty (30) day period, a battery operated carbon

monoxide detector with an alarm shall be installed.

2. APPROVED CARBON MONOXIDE DETECTORS. Each carbon monoxide detector as required in accordance with the above provisions shall

comply with NFPA 720 and be ANSI/UL 2034 listed and IAS certified.

3. SIGNAGE. A metal or plastic identification plate shall be permanently mounted to the exterior of the building at a minimum height of eight (8)

feet above grade directly in line with the exhaust vent terminal for the horizontally vented gas fueled heating appliance or equipment. The sign

shall read, in print size no less than one-half (1/2) inch in size, ”GAS VENT DIRECTLY BELOW. KEEP CLEAR OF ALL OBSTRUCTIONS”.

4. INSPECTION. The state or local gas inspector of the side wall horizontally vented gas fueled equipment shall not approve the installation unless,

upon inspection, the inspector observes carbon monoxide detectors and signage installed in accordance with the provisions of 248 CMR

5.08(2)(a)1 through 4.

5. EXEMPTIONS: The following equipment is exempt from 248 CMR 5.08(2)(a)1 through 4:

(1.) The equipment listed in Chapter 10 entitled ”Equipment Not Required To Be Vented” in the most current edition of NFPA 54 as adopted

by the Board; and

(2.) Product Approved side wall horizontally vented gas fueled equipment installed in a room or structure separate from the dwelling, building

or structure used in whole or in part for residential purposes.

a. MANUFACTURER REQUIREMENTS - GAS EQUIPMENT VENTING SYSTEM PROVIDED. When the manufacturer of Product

Approved side wall horizontally vented gas equipment provides a venting system design or venting system components with the equipment, the

instructions provided by the manufacturer for installation of the equipment and the venting system shall include:

1. Detailed instructions for the installation of the venting system design or the venting system components; and

2. A complete parts list for the venting system design or venting system.

a. MANUFACTURER REQUIREMENTS - GAS EQUIPMENT VENTING SYSTEM NOT PROVIDED. When the manufacturer of a Product

Approved side wall horizontally vented gas fueled equipment does not provide the parts for venting the flue gases, but identifies “special

venting systems”, the following requirements shall be satisfied by the manufacturer:

3. The referenced “special venting system” instructions shall be included with the appliance or equipment installation instructions; and

4. The “special venting systems” shall be Product Approved by the Board, and the instructions for that system shall include a parts list and detailed

installation instructions.

a. A copy of all installation instructions for all Product Approved side wall horizontally vented gas fueled equipment, all venting instructions, all

parts lists for venting instructions, and/or all venting design instructions shall remain with the appliance or equipment at the completion of the

installation.

For questions regarding these requirements, please contact the Commonwealth of Massachusetts Board of State Examiners of Plumbers and Gas

Fitters, 239 Causeway Street, Boston, MA 02114. 617-727-9952.

F96VTN and G96VTN: Installation, Start-up, Operating and Service and Maintenance Instructions

Manufacturer reserves the right to change, at any time, specifications and designs without notice and without obligations.

A210210

Fig. 1 – Dimensional Drawing

SAFETY CONSIDERATIONS

FURNACE SIZE A B C D SHIP WT.

LB (KG)

CABINET WIDTH OUTLET WIDTH BOTTOM INLET WIDTH AIR INTAKE

0401410 14-3/16 (361) 12-1/2 (319) 12-9/16 (322) 7-1/8 (181) 123 (55.8)

0601714 17-1/2 (445) 15-7/8 (403) 16 (406) 8-3/4 (222) 139 (63.0)

0801716 17-1/2 (445) 15-7/8 (403) 16 (406) 8-3/4 (222) 147 (66.7)

1002120 21 (533) 19-3/8 (492) 19-1/2 (495) 10-1/2 (267) 170 (77.1)

1002122 21 (533) 19-3/8 (492) 19-1/2 (495) 10-1/2 (267) 171 (77.6)

1202422 24-1/2 (622) 22-7/8 (581) 23 (584) 12-1/4 (311) 190 (86.2)

U.S. ECCN: Not Subject to Regulation (N.S.R.)

SD5660-4 REV. -

NOTE: ALL DIMENSIONS IN INCH (MM)

WARNING

FIRE, INJURY, OR DEATH HAZARD

Failure to follow this warning could result in property damage, personal

injury, or death.

This furnace was manufactured to operate with natural gas. When fuel

supply is Liquid Propane (LP), this furnace must be converted with a

factory approved LP conversion kit. See furnace rating plate for

approved conversion kit.

WARNING

FIRE, EXPLOSION, ELECTRICAL SHOCK, AND

CARBON MONOXIDE POISONING HAZARD

Failure to follow this warning could result in dangerous operation,

personal injury, death, or property damage.

Improper installation, adjustment, alteration, service, maintenance, or

use can cause carbon monoxide poisoning, explosion, fire, electrical

shock, or other conditions which may cause personal injury or property

damage. Consult a qualified service agency, local gas supplier, or your

distributor or branch for information or assistance. The qualified

service agency must use only factory-authorized accessories and

replacement parts when installing and servicing this product.

F96VTN and G96VTN: Installation, Start-up, Operating and Service and Maintenance Instructions

Manufacturer reserves the right to change, at any time, specifications and designs without notice and without obligations.

Improper installation, adjustment, alteration, service, maintenance, or

use can cause explosion, fire, electrical shock, or other conditions which

may cause death, personal injury, or property damage. Consult a

qualified installer, service agency, or your distributor or branch for

information or assistance. The qualified installer or agency must use

factory-authorized kits or accessories when modifying this product.

Refer to the individual instructions packaged with the kits or accessories

when installing.

Installing and servicing heating equipment can be hazardous due to gas

and electrical components. Only trained and qualified personnel should

install, repair, or service heating equipment. Untrained personnel can

perform basic maintenance functions such as cleaning and replacing air

filters. All other operations must be performed by trained service

personnel. When working on heating equipment, observe precautions in

literature, on tags, and on labels attached to or shipped with furnace and

other safety precautions that may apply.

These instructions cover minimum requirements and conform to existing

national standards and safety codes. In some instances, these instructions

exceed certain local codes and ordinances, especially those that may not

have kept up with changing residential construction practices. We

require these instructions as a minimum for a safe installation.

Follow all safety codes. Wear safety glasses, protective clothing, and

work gloves. Have a fire extinguisher available. Read these instructions

thoroughly and follow all warnings or cautions included in literature and

attached to the unit.

This is the safety-alert symbol . When you see this symbol on the

furnace and in instructions or manuals, be alert to the potential for

personal injury.

Understand the signal words DANGER, WARNING, and CAUTION.

These words are used with the safety-alert symbol. DANGER identifies

the most serious hazards which will result in severe personal injury or

death. WARNING signifies a hazard which could result in personal

injury or death. CAUTION is used to identify hazards which may result

in minor personal injury or product and property damage. NOTE and

NOTICE are used to highlight suggestions which will result in enhanced

installation, reliability, or operation.

1. Use only with type of gas approved for this furnace. Refer to the

furnace rating plate.

2. Install this furnace only in a location and position as specified in the

“Location” section of these instructions.

3. Provide adequate combustion and ventilation air to the furnace

space as specified in “Air for Combustion and Ventilation” section.

4. Combustion products must be discharged outdoors. Connect this

furnace to an approved vent system only, as specified in the

“Venting” section of these instructions.

5. Never test for gas leaks with an open flame. Use a commercially

available soap solution made specifically for the detection of leaks

to check all connections, as specified in the “Gas Piping” section.

6. Always install furnace to operate within the furnace’s intended

temperature-rise range with a duct system which has an external

static pressure within the allowable range, as specified in the

“Start-Up, Adjustments, and Safety Check” section. See furnace

rating plate.

7. When a furnace is installed so that supply ducts carry air circulated

by the furnace to areas outside the space containing the furnace, the

return air shall also be handled by duct(s) sealed to the furnace

casing and terminating outside the space containing the furnace.

See “Air Ducts” section.

8. A gas-fired furnace for installation in a residential garage must be

installed as specified in the warning box in the “Location” section.

9. The furnace may be used for construction heat provided that the

furnace installation and operation complies with the first

CAUTION in the LOCATION section of these instructions.

10. These Multipoise Gas-Fired Furnaces are CSA design-certified for

use with natural and propane gases (see furnace rating plate) and for

installation in alcoves, attics, basements, closets, utility rooms,

crawlspaces, and garages. The furnace is factory-shipped for use

with natural gas. A CSA (A.G.A. and C.G.A.) listed accessory gas

conversion kit is required to convert furnace for use with propane

gas.

11. See Table 1 for required clearances to combustible construction.

WARNING

FIRE, EXPLOSION, ELECTRICAL SHOCK, AND

CARBON MONOXIDE POISONING HAZARD

Failure to follow this warning could result in dangerous operation,

personal injury, death, or property damage.

Furnaces shall NOT be twinned (i.e. tandem or staged operation) unless

approved in factory technical specifications literature for the furnace.

A factory authorized, field-supplied Twinning Kit MUST be used.

Consult furnace pre-sale literature for specific models approved for

twinning and the correct twinning kit. Twinned furnaces must be

installed on both a common supply AND a common return duct system

as shown in the Twinning Kit Installation Instructions. Only two

furnaces can be twinned on a common supply and return duct system

using a factory authorized twinning kit.

WARNING

FIRE HAZARD

Failure to follow this warning could result in personal injury, death, or

property damage.

Solvents, cements and primers are combustible. Keep away from heat,

sparks and open flame. Use only in well-ventilated areas. Avoid

breathing in vapor or allowing contact with skin or eyes.

CAUTION

FURNACE RELIABILITY HAZARD

Failure to follow this caution may result in unit component damage.

Application of this furnace should be indoors with special attention

given to vent sizing and material, gas input rate, air temperature rise,

unit leveling, and unit sizing.

WARNING

FIRE, INJURY, OR DEATH HAZARD

Failure to follow this warning could result in property damage, personal

injury, or death.

Do not bypass any of the safety controls in the furnace, including but

not limited to the main limit switch, rollout or burner thermal switch,

and pressure switch/pressure transducer.

CAUTION

CUT HAZARD

Failure to follow this caution may result in personal injury.

Sheet metal parts may have sharp edges or burrs. Use care and wear

appropriate protective clothing, safety glasses and gloves when

handling parts, and servicing furnaces.

F96VTN and G96VTN: Installation, Start-up, Operating and Service and Maintenance Instructions

Manufacturer reserves the right to change, at any time, specifications and designs without notice and without obligations.

Table 1 – Minimum Clearances to Combustible Materials for All

Units

*Consult local building codes.

12. Maintain a 1-in. (25 mm) clearance from combustible materials to

supply air ductwork for a distance of 36 in. (914 mm) horizontally

from the furnace. See NFPA 90B or local code for further

requirements.

13. These furnaces SHALL NOT be installed directly on carpeting,

combustible tile, or any other combustible material other than wood

flooring. In downflow installations, factory accessory floor base

MUST be used when installed on combustible materials and wood

flooring. Special base is not required when this furnace is installed

on a manufacturer’s specified coil assembly or coil box (see furnace

clearance label).

INTRODUCTION

A12181

Fig. 2 – Multipoise Orientations

This 4-way multipoise Category IV condensing furnace is CSA

design-certified as a direct-vent (2-pipe) or non-direct vent (1-pipe)

furnace. See Fig. 2. The furnace is factory-shipped for use with natural

gas. The furnace can be converted in the field for use with propane gas

when a factory-supplied conversion kit is used. Refer to the furnace

rating plate for conversion kit information.

This furnace is not approved for installation in mobile homes,

recreational vehicles, or outdoors.

This furnace is designed for minimum continuous return-air temperature

of 60°F (15°C) db or intermittent operation down to 55°F (13°C) db such

as when used with a night setback thermostat. Return-air temperature

must not exceed 80°F (27°C) db. Failure to follow these return-air

temperature limits may affect reliability of heat exchangers, motors, and

controls. See Fig. 3.

A150573

Fig. 3 – Freeze Protection and Return Air Temperature

The furnace should be sized to provide 100 percent of the design heating

load requirement plus any margin that occurs because of furnace model

size capacity increments. None of the furnace model sizes can be used if

the heating load is 20,000 BTU or lower. Use Air Conditioning

Contractors of America (Manual J and S); American Society of Heating,

Refrigerating, and Air-Conditioning Engineers; or other approved

engineering method to calculate heating load estimates and select the

furnace. Excessive oversizing of the furnace may cause the furnace

and/or vent to fail prematurely, customer discomfort and/or vent

freezing.

Failure to follow these guidelines is considered faulty installation and/or

misapplication of the furnace; and resulting failure, damage, or repairs

may impact warranty coverage.

For accessory installation details, refer to the applicable instruction

literature.

NOTE: Remove all shipping materials, loose parts bag, and literature

before operating the furnace. See Table 2.

Table 2 – Loose Parts Bag

NOTE: The 40K models are the only furnaces that receive the outlet

restrictor in loose parts bag. See Maximum Equivalent Vent Length

Table for usage.

POSITION CLEARANCE

Rear 0 (0 mm)

Front (Combustion air openings in

furnace and in structure) 1 in. (25 mm)

Required for service *24 in. (610 mm)

All Sides of Supply Plenum *1 in. (25 mm)

Sides 0 (0 mm)

Vent 0 (0 mm)

Top of Furnace 1 in. (25 mm)

NOTICE

IMPORTANT INSTALLATION AND START-UP PROCEDURES

Failure to follow this procedure may result in a nuisance smoke or odor

complaint.

The manifold pressure, gas rate by meter clocking, temperature rise and

operation must be checked after installation. Minor smoke and odor

may be present temporarily after start-up from the manufacturing

process. Some occupants are more sensitive to this minor smoke and

odor. It is recommended that doors and windows be open during the

first heat cycle.

THE BLOWER IS LOCATED

TO THE RIGHT OF THE

BURNER SECTION, AND

CONDITIONED AIR IS

DISCHARGED TO THE LEFT.

THE BLOWER IS

LOCATED BELOW THE

BURNER SECTION, AND

CONDITIONED AIR IS

DISCHARGED UPWARD.

THE BLOWER IS

LOCATED ABOVE THE

BURNER SECTION, AND

CONDITIONED AIR IS

DISCHARGED DOWNWARD

THE BLOWER IS

LOCATED TO THE LEFT

OF THE BURNER SECTION,

AND CONDITIONED AIR IS

DISCHARGED TO THE RIGHT.

WARNING

FIRE HAZARD

Failure to follow this warning could result in personal injury, death

and/or property damage.

Do not install the furnace on its back or hang furnace with control

compartment facing downward. Safety control operation will be

adversely affected. Never connect return-air ducts to the back of the

furnace. See Fig. 4.

DESCRIPTION QUANTITY

Outlet Restrictor Plate (provided with 40K BTUH

furnaces only; see Note) 1

Air Intake Pipe Flange 1

Vent Pipe Flange 1

Pipe Flange Gaskets 2

Sharp Tip Screws (Vent and Inlet Flanges) 10

Vent Pipe Coupling 1

Vent Pipe Coupling Clamps 2

Pressure Switch Tube 1

Rubber Drain Elbow 1

Drain Tube Clamps 4

1/2-in. CPVC to 3/4-in. PVC Pipe Adapter 1

Gas Line Grommet 1

Junction Box Cover 1

Junction Box Base 1

Green Ground Screw 1

Blunt Tip Screws (Junction Box) 3

Thermostat Wire Grommet 1

Drain Extension Tube (Z-pipe) (Provided separately in

furnace) 1

80 Ý&

Ý&

SUPPLY AIR

SEE PRODUCT DATA FOR

ACCESSORY CONDENSATE

TRAP HEATER AND CONDENSATE

DRAIN LINE PROTECTION.

F96VTN and G96VTN: Installation, Start-up, Operating and Service and Maintenance Instructions

Manufacturer reserves the right to change, at any time, specifications and designs without notice and without obligations.

A12182

Fig. 4 – Prohibited Installations

CODES AND STANDARDS

Follow all national and local codes and standards in addition to these

instructions. The installation must comply with regulations of the

serving gas supplier, local building, heating, plumbing, and other codes.

In absence of local codes, the installation must comply with the national

codes listed below and all authorities having jurisdiction.

In the United States and Canada, follow all codes and standards for the

following:

A93044

Fig. 5 – Installation in a Garage

Safety

• US: Current edition of National Fuel Gas Code NFPA 54/ANSI

Z223.1 and the Installation Standards, Warm Air Heating and Air

Conditioning Systems ANSI/NFPA 90B

• CANADA: Current edition of National Standard of Canada, Natural

Gas and Propane Installation Code (NSCNGPIC) CAN/CSA B149.1

General Installation

• US: NFPA 54/ANSI Z223.1 and the NFPA 90B. For copies, contact

the National Fire Protection Association Inc., Batterymarch Park,

Quincy, MA 02269; or for only the NFPA 54/ANSI Z223.1 contact the

American Gas Association, 400 N. Capitol, N.W., Washington DC

20001

• CANADA: NSCNGPIC. For a copy, contact Standard Sales, CSA

International, 178 Rexdale Boulevard, Etobicoke (Toronto), Ontario,

M9W 1R3, Canada

Combustion and Ventilation Air

• US: Section 9.3 of the current edition of NFPA54/ANSI Z223.1 Air

for Combustion and Ventilation

• CANADA: Part 8 of the current edition of CAN/CSA B149.1, Venting

Systems and Air Supply for Appliances

Duct Systems

• US and CANADA: Air Conditioning Contractors Association

(ACCA) Manual D, Sheet Metal and Air Conditioning Contractors

National Association (SMACNA), or American Society of Heating,

Refrigeration, and Air Conditioning Engineers (ASHRAE)

Fundamentals Handbook

Acoustical Lining and Fibrous Glass Duct

• US and CANADA: Current edition of SMACNA, NFPA 90B as tested

by UL Standard 181 for Class I Rigid Air Ducts

Gas Piping and Gas Pipe Pressure Testing

• US: Current edition of NFPA 54/ANSI Z223.1; Chapters 5, 6, 7, and 8

and national plumbing codes.

CANADA: Current edition of CAN/CSA-B149.1, Parts 4, 5, 6, and 9.

In the state of Massachusetts:

• This product must be installed by a licensed plumber or gas fitter.

• When flexible connectors are used, the maximum length shall not

exceed 36 in. (914 mm).

• When lever type gas shutoffs are used they shall be T-handle type.

• The use of copper tubing for gas piping is not approved by the state of

Massachusetts.

Electrical Connections

• US: Current edition of National Electrical Code (NEC) NFPA 70.

• CANADA: Current edition of Canadian Electrical Code CSA C22.1

Condensate Drain Connection

• US: Current edition of National Standard Plumbing Code, Section 8.7.

• Canada: Current edition of National Plumbing Code of Canada.

ELECTROSTATIC DISCHARGE (ESD)

PRECAUTIONS PROCEDURE

1. Disconnect all power to the furnace. Multiple disconnects may be

required. DO NOT TOUCH THE CONTROL OR ANY WIRE

CONNECTED TO THE CONTROL PRIOR TO DISCHARGING

YOUR BODY’S ELECTROSTATIC CHARGE TO GROUND.

2. Firmly touch the clean, unpainted, metal surface of the furnace

chassis which is close to the control. Tools held in a person’s hand

during grounding will be satisfactorily discharged.

WARNING

FIRE, INJURY OR DEATH HAZARD

Failure to follow this warning could result in personal injury, death

and/or property damage.

When the furnace is installed in a residential garage, the burners and

burner ignition devices must be located at least 18 in. (457 mm) above

the floor. The furnace must be located or protected to avoid damage by

vehicles. When the furnace is installed in a public garage, airplane

hangar, or other building having a hazardous atmosphere, the furnace

must be installed in accordance with the current edition of NFPA

54/ANSI Z223.1 or CAN/CSA B149.2. See Fig. 5.

BACK POSITIONED

DOWNWARD

AIR RETURN

CUT IN BACK

BACK POSITIONED

UPWARD

18-IN. (457.2 mm)

MINIMUM TO BURNERS

CAUTION

FURNACE RELIABILITY HAZARD

Failure to follow this caution may result in unit component damage.

Electrostatic discharge can affect electronic components. Take

precautions during furnace installation and servicing to protect the

furnace electronic control. Precautions will prevent electrostatic

discharges from personnel and hand tools which are held during the

procedure. These precautions will help to avoid exposing the control to

electrostatic discharge by putting the furnace, the control, and the

person at the same electrostatic potential.

F96VTN and G96VTN: Installation, Start-up, Operating and Service and Maintenance Instructions

Manufacturer reserves the right to change, at any time, specifications and designs without notice and without obligations.

3. After touching the chassis, you may proceed to service the control

or connecting wires as long as you do nothing to recharge your

body with static electricity (for example; DO NOT move or shuffle

your feet, do not touch ungrounded objects, etc.).

4. If you touch ungrounded objects (and recharge your body with

static electricity), firmly touch a clean, unpainted metal surface of

the furnace again before touching control or wires.

5. Use this procedure for installed and uninstalled (ungrounded)

furnaces.

6. Before removing a new control from its container, discharge your

body’s electrostatic charge to ground to protect the control from

damage. If the control is to be installed in a furnace, follow items 1

through 4 before bringing the control or yourself in contact with the

furnace. Put all used and new controls into containers before

touching ungrounded objects.

7. An ESD service kit (available from commercial sources) may also

be used to prevent ESD damage.

ACCESSORIES

See Specification Sheet for a list of accessories for this product.

LOCATION

General

These furnaces are shipped with materials to assist in proper furnace

installation. These materials are shipped in the main blower

compartment. See Table 2 for loose parts bag contents.

This furnace must:

• be installed so the electrical components are protected from water.

• not be installed directly on any combustible material other than wood

flooring (refer to SAFETY CONSIDERATIONS).

• be located close to the chimney or vent and attached to an air

distribution system. Refer to Air Ducts section.

• be provided ample space for servicing and cleaning. Always comply

with minimum fire protection clearances shown in Table 1 or on the

furnace clearance to combustible construction label.

The following types of furnace installations may require OUTDOOR

AIR for combustion due to chemical exposures:

• Commercial buildings

• Buildings with indoor pools

• Laundry rooms

• Hobby or craft rooms

• Chemical storage areas

If air is exposed to the following substances, it should not be used for

combustion air, and outdoor air may be required for combustion:

• Permanent wave solutions

• Chlorinated waxes and cleaners

• Chlorine based swimming pool chemicals

• Water softening chemicals

• De-icing salts or chemicals

• Carbon tetrachloride

• Halogen type refrigerants

• Cleaning solvents (such as perchloroethylene)

• Printing inks, paint removers, varnishes, etc.

• Hydrochloric acid

• Cements and glues

• Antistatic fabric softeners for clothes dryers

• Masonry acid washing materials

All fuel-burning equipment must be supplied with air for fuel

combustion. Sufficient air must be provided to avoid negative pressure

in the equipment room or space. A positive seal must be made between

the furnace cabinet and the return-air duct to prevent pulling air from the

burner area.

CAUTION

PERSONAL INJURY AND/OR PROPERTY DAMAGE

HAZARD

Improper use or installation of this furnace may result in premature

furnace component failure. Unless otherwise prohibited, this gas

furnace may be used for heating buildings under construction provided

that:

- The furnace is permanently installed with all electrical wiring,

piping, venting and ducting installed according to these

installation instructions. A return air duct is provided, sealed to

the furnace casing, and terminated outside the space containing

the furnace. This prevents a negative pressure condition as

created by the circulating air blower, causing a flame rollout

and/or drawing combustion products into the structure.

- The furnace is controlled by a thermostat. It may not be “hot

wired” to provide heat continuously to the structure without

thermostatic control.

- Clean outside air is provided for combustion. This is to

minimize the corrosive effects of adhesives, sealers and other

construction materials. It also prevents the entrainment of

drywall dust into combustion air, which can cause fouling and

plugging of furnace components.

- The temperature of the return air to the furnace is maintained

between 55°F (13°C) and 80°F (27°C), with no evening setback

or shutdown. The use of the furnace while the structure is under

construction is deemed to be intermittent operation per our

installation instructions.

- The air temperature rise is within the rated rise range on the

furnace rating plate, and the gas input rate has been set to the

nameplate value.

- The filters used to clean the circulating air during the

construction process must be either changed or thoroughly

cleaned prior to occupancy.

- The furnace, ductwork and filters are cleaned as necessary to

remove drywall dust and construction debris from all HVAC

system components after construction is completed.

- Verify proper furnace operating conditions including ignition,

gas input rate, air temperature rise, and venting according to

these installation instructions.

WARNING

CARBON MONOXIDE POISONING / COMPONENT

DAMAGE HAZARD

Failure to follow this warning could result in personal injury or death

and unit component damage.

Corrosive or contaminated air may cause failure of parts containing flue

gas, which could leak into the living space. Air for combustion must not

be contaminated by halogen compounds, which include fluoride,

chloride, bromide, and iodide. These elements can corrode heat

exchangers and shorten furnace life. Air contaminants are found in

aerosol sprays, detergents, bleaches, cleaning solvents, salts, air

fresheners, and other household products. Do not install furnace in a

corrosive or contaminated atmosphere. Make sure all combustion and

circulating air requirements are met, in addition to all local codes and

ordinances.

F96VTN and G96VTN: Installation, Start-up, Operating and Service and Maintenance Instructions

Manufacturer reserves the right to change, at any time, specifications and designs without notice and without obligations.

AIR FOR COMBUSTION AND VENTILATION

Introduction

Direct Vent (2-pipe) Applications

When the furnace is installed as a direct vent (2-pipe) furnace, no special

provisions for air for combustion are required. However, other gas

appliances installed in the space with the furnace may require outside air

for combustion. Follow the guidelines below to ensure that other gas

appliances have sufficient air for combustion.

Non-Direct Vent (1-pipe) Applications

When the furnace is installed as a non-direct vent (1-pipe) furnace, it

will be necessary to ensure there is adequate air for combustion. Other

gas appliances installed with the furnace may also require air for

combustion and ventilation in addition to the amount of combustion air

and ventilation air required for the furnace. Follow the guidelines below

to ensure that the furnace and other gas appliances have sufficient air for

combustion.

Ventilated Combustion Air Applications (for U.S. Only)

When the furnace is installed using the ventilated combustion air option,

the attic or crawlspace must freely communicate with the outdoor to

provide sufficient air for combustion. The combustion air pipe cannot be

terminated in attics or crawlspaces that use ventilation fans designed to

operate during the heating season. If ventilation fans are present in these

areas, the combustion air pipe must terminate outdoors as a Direct Vent/

2-Pipe system.

All air for combustion is piped directly to the furnace from a space that is

well ventilated with outdoor air (such as an attic, crawl space or

equipment closet) and the space is well isolated from the living space or

garage. In addition, other gas appliances installed in the space with the

furnace may require outside air for combustion. Follow the guidelines

below to ensure that the roof or crawlspace walls have sufficient free

area to provide sufficient air for combustion and ventilation for the

furnaces. The guidelines below can be used to ensure that other gas

appliances have sufficient air for combustion.

Provisions for adequate combustion, ventilation, and dilution air must be

provided in accordance with:

• USA Installations: Section 9.3 of the current edition of NFPA

54/ANSI Z223.1, Air for Combustion and Ventilation and applicable

provisions of the local building codes.

The requirements for combustion and ventilation air depend upon

whether or not the furnace is located in a space having a volume of at

least 50 cubic feet per 1,000 BTUh input rating for all gas appliances

installed in the space.

• Spaces having less than 50 cubic feet per 1,000 BTUh (4.8 cubic

meters per kW) require the Outdoor Combustion Air Method.

• Spaces having at least 50 cubic feet per 1,000 BTUh (4.8 cubic meters

per kW) may use the Indoor Combustion Air, Standard or Known Air

Infiltration Method.

Outdoor Combustion Air Method

1. Provide the space with sufficient air for proper combustion,

ventilation, and dilution of flue gases using permanent horizontal or

vertical duct(s) or opening(s) directly communicating with the

outdoors or spaces that freely communicate with the outdoors.

2. Fig. 6 illustrates how to provide TWO OUTDOOR OPENINGS,

one inlet and one outlet combustion and ventilation air opening, to

the outdoors.

a. One opening MUST commence within 12 in. (300 mm) of the

ceiling and the second opening MUST commence within 12 in.

(300 mm) of the floor.

b. Size openings and ducts per Fig. 6 and Table 3.

c. TWO HORIZONTAL DUCTS require 1 sq. in. (645 sq. mm) of

free area per 2,000 BTUh (1,100 mm2/kW) of combined input

for all gas appliances in the space per Fig. 6 and Table 3.

d. TWO OPENINGS OR VERTICAL DUCTS require 1 sq. in.

(645 sq. mm) of free area per 4,000 BTUh (550 mm2/kW) for

combined input of all gas appliances in the space per Fig. 6 and

Table 3.

3. ONE OUTDOOR OPENING requires:

a. 1 sq. in. (645 sq. mm) of free area per 3,000 BTUh (734

mm2/kW) for combined input of all gas appliances in the space

per Fig. 6 and Table 3.

b. Not less than the sum of the areas of all vent connectors in the

space.

The opening shall commence within 12 in. (300 mm) of the ceiling.

Appliances in the space shall have clearances of at least 1 in. (25 mm)

from the sides and back and 6 in. (150 mm) from the front. The opening

shall directly communicate with the outdoors or shall communicate

through a vertical or horizontal duct to the outdoors or spaces (crawl or

attic) that freely communicate with the outdoors.

Standard and Known-Air-Infiltration Rate Methods

Indoor air is permitted for combustion, ventilation, and dilution, if the

Standard or Known-Air-Infiltration Method is used.

Standard Method

1. The space has no less volume than 50 cubic feet per 1,000 BTUh of

the maximum input ratings for all gas appliances installed in the

space and

CAUTION

FURNACE CORROSION HAZARD

Failure to follow this caution may result in furnace damage.

Air for combustion must not be contaminated by halogen compounds,

which include fluoride, chloride, bromide, and iodide. These elements

can corrode heat exchangers and shorten furnace life. Air contaminants

are found in aerosol sprays, detergents, bleaches, cleaning solvents,

salts, air fresheners, and other household products.

WARNING

CARBON MONOXIDE POISONING HAZARD

Failure to follow this warning could result in personal injury or death.

The operation of exhaust fans, kitchen ventilation fans, clothes dryers,

attic exhaust fans or fireplaces could create a NEGATIVE PRESSURE

CONDITION at the furnace. Make-up air MUST be provided for the

ventilation devices, in addition to that required by the furnace. Refer to

the Carbon Monoxide Poisoning Hazard warning in the venting section

of these instructions to determine if an adequate amount of make--up

air is available.

WARNING

CARBON MONOXIDE POISONING HAZARD

Failure to follow this warning could result in personal injury or death.

Many homes require air to be supplied from outdoors for furnace

combustion, ventilation, and dilution of flue gases.

The furnace combustion air supply must be provided in accordance

with this instruction manual.

F96VTN and G96VTN: Installation, Start-up, Operating and Service and Maintenance Instructions

Manufacturer reserves the right to change, at any time, specifications and designs without notice and without obligations.

2. The air infiltration rate is not known to be less than 0.40 air changes

per hour (ACH).

The Known Air Infiltration Rate Method shall be used, if the infiltration

rate is known to be:

1. Less than 0.40 ACH and

2. Equal to or greater than 0.10 ACH

Infiltration rates greater than 0.60 ACH shall not be used. The minimum

required volume of the space varies with the number of ACH and shall

be determined per Table 4 or Equations 1 and 2. Determine the minimum

required volume for each appliance in the space and add the volumes

together to get the total minimum required volume for the space.

Table 4 - Minimum Space Volumes were determined by using the

following equations from the current edition of the National Fuel Gas

Code ANSI Z223.1/NFPA 54, 9.3.2.2:

1. For other than fan-assisted appliances, such as a draft

hood-equipped water heater:

A04002

2. For fan-assisted appliances such as this furnace:

A04003

If: Iother = combined input of all other than fan-assisted appliances in

BTUh/hr

Ifan = combined input of all fan-assisted appliances in BTUh/hr

ACH = air changes per hour (ACH shall not exceed 0.60.)

The following requirements apply to the Standard Method and to the

Known Air Infiltration Rate Method.

1. Adjoining rooms can be considered part of a space if:

a. There are no closeable doors between rooms.

b. Combining spaces on same floor level. Each opening shall have

free area of at least 1 in.2/1,000 BTUh (2,000 mm2/kW) of the

total input rating of all gas appliances in the space, but not less

than 100 in.2 (0.06 m2). One opening shall commence within 12

in. (300 mm) of the ceiling and the second opening shall

commence within 12 in. (300 mm) of the floor. The minimum

dimension of air openings shall be at least 3 in. (80 mm). See

Fig. 7.

c. Combining space on different floor levels. The volumes of

spaces on different floor levels shall be considered as

communicating spaces if connected by one or more permanent

openings in doors or floors having free area of at least 2

in.2/1,000 BTUh (4,400 mm2/kW) of total input rating of all gas

appliances.

2. An attic or crawlspace may be considered a space that freely

communicates with the outdoors provided there are adequate

permanent ventilation openings directly to outdoors having free

area of at least 1-in.2/4,000 BTUh of total input rating for all gas

appliances in the space.

3. In spaces that use the Indoor Combustion Air Method, infiltration

should be adequate to provide air for combustion, permanent

ventilation and dilution of flue gases. However, in buildings with

unusually tight construction, additional air MUST be provided

using the methods described in the Outdoor Combustion Air

Method section.

4. Unusually tight construction is defined as Construction with:

a. Walls and ceilings exposed to the outdoors have a continuous,

sealed vapor barrier. Openings are gasketed or sealed and

b. Doors and openable windows are weatherstripped and

c. Other openings are caulked or sealed. These include joints

around window and door frames, between sole plates and floors,

between wall-ceiling joints, between wall panels, at penetrations

for plumbing, electrical and gas lines, etc.

Combination of Indoor and Outdoor Air

1. Indoor openings shall comply with the Indoor Combustion Air

Method below and,

2. Outdoor openings shall be located as required in the Outdoor

Combustion Air Method mentioned previously and,

3. Outdoor openings shall be sized as follows:

a. Calculate the Ratio of all Indoor Space volume divided by

required volume for Indoor Combustion Air Method below.

b. Outdoor opening size reduction Factor is 1 minus the Ratio in a.

above.

c. Minimum size of Outdoor openings shall be the size required in

Outdoor Combustion Air Method above multiplied by reduction

Factor in b. above. The minimum dimension of air openings shall

be not less than 3 in. (80 mm).

CONDENSATE TRAP

Condensate Trap - Upflow Orientation

When the furnace is installed in the upflow position, it is not necessary

to relocate the condensate trap or associated tubing. Refer to Fig. 8 for

upflow condensate trap information. Refer to Condensate Drain section

for information how to install the condensate drain.

Condensate Trap - Downflow Orientation.

When the furnace is installed in the downflow position, the condensate

trap will be initially located at the upper left corner of the collector box,

as received from the factory. See the top image in Fig. 9. When the

furnace is installed in the downflow orientation, the condensate trap

must be relocated for proper condensate drainage. See the bottom image

in Fig. 9.

To Relocate the Condensate Trap:

• Orient the furnace in the downflow position.

•Fig. 9 shows the condensate trap and tubing before and after

relocation. Refer to Fig. 9 to begin the trap conversion.

• Refer to Condensate Drain section for information how to install the

condensate drain.

Condensate Trap - Horizontal Orientation.

When the furnace is installed in the horizontal right position, the

condensate trap will be initially located at the bottom of the collector

box, as received from the factory. See the top image in Fig. 10. When the

furnace is installed in the horizontal left position, the condensate trap

will be initially located at the top of the collector box, as received from

the factory. See the top image in Fig. 11. In both cases the trap must be

repositioned on the collector box for proper condensate drainage. See the

bottom images in Fig. 10 and 11.

A field-supplied, accessory Horizontal Installation Kit (trap grommet) is

required for all direct-vent horizontal installations (only). The kit

contains a rubber casing grommet designed to seal between the furnace

casing and the condensate trap. See Fig. 18.

Volume

Other

=21ft

ACH

other

1000 Btu/hr

Volume

Fan

=15ft

ACH

fan

1000 Btu/hr

F96VTN and G96VTN: Installation, Start-up, Operating and Service and Maintenance Instructions

Manufacturer reserves the right to change, at any time, specifications and designs without notice and without obligations.

Table 3 – Minimum Free Area Required for Each Combustion Air Opening or Duct to Outdoors

EXAMPLES: Determining Free Area

Table 4 – Minimum Space Volumes for 100% Combustion, Ventilation and Dilution Air from Outdoors

NP = Not Permitted

L12F012

Fig. 6 – Air for Combustion, Ventilation, and Dilution for Outdoors

L12F013

Fig. 7 – Air for Combustion, Ventilation, and Dilution from Indoors

FURNACE INPUT

(BTUH)

TWO HORIZONTAL DUCTS

(1 SQ. IN./2,000 BTUH)

(1,100 SQ. MM/KW)

SINGLE DUCT OR OPENING

(1 SQ. IN./3,000 BTUH)

(734 SQ. MM/KW)

TWO OPENINGS OR

VERTICAL DUCTS

(1 SQ. IN./4,000 BTUH)

(550 SQ. MM/KW)

Free Area of

Opening and Duct

Sq. In (Sq. mm)

Round Duct

In. (mm) Dia

Free Area of

Opening and Duct

Sq. In (Sq. mm)

Round Duct

In. (mm) Dia

Free Area of

Opening and Duct

Sq. In (mm)

Round Duct

In. (mm) Dia.

40,000*

*. Not all families have these models.

20 (12904) 5 (127) 14 (8696) 5 (127) 10 (6452) 4 (102)

60,000 30 (19355) 6 (152) 20 (13043) 5 (127) 15 (9678) 5 (127)

80,000 40 (25807) 7 (178) 27 (17391) 6 (152) 20 (12904) 5 (127)

100,000 50 (32258) 8 (203) 34 (21739) 7 (178) 25 (16130) 6 (152)

120,000 60 (38709) 9 (229) 40 (26087) 7 (178) 30 (19355) 6 (152)

140,000* 70 (45161) 10 (254) 47 (30435) 8 (203) 35 (22581) 7 (178)

FURNACE WATER HEATER TOTAL INPUT

100,000 + 30,000 = (130,000 divided by 4,000) = 32.5 Sq. In. for each two Vertical Ducts or Openings

60,000 + 40,000 = (100,000 divided by 3,000) = 33.3 Sq. In. for each Single Duct or Opening

80,000 + 30,000 = (110,000 divided by 2,000) = 55.0 Sq. In. for each two Horizontal Ducts

OTHER THAN FAN-ASSISTED TOTAL

(1,000’S BTUH GAS INPUT RATE)

FAN-ASSISTED TOTAL

(1,000’S BTUH GAS INPUT RATE)

ACH 30 40 50 40 60 80 100 120 140

Space Volume Ft3 (M3)

0.60 1,050 (29.7) 1,400 (39.6) 1,750 (49.5) 1,400 (39.6) 1,500 (42.5) 2,000 (56.6) 2,500 (70.8) 3,000 (84.9) 3,500 (99.1)

0.50 1,260 (35.6) 1,680 (47.5) 2,100 (59.4) 1,680 (47.5) 1,800 (51.0) 2,400 (67.9) 3,000 (84.9) 3,600 (101.9) 4,200 (118.9)

0.40 1,575 (44.5) 2,100 (59.4) 2,625 (74.3) 2,100 (59.4) 2,250 (63.7) 3,000 (84.9) 3,750 (106.1) 4,500 (127.3) 5,250 (148.6)

0.30 2,100 (59.4) 2,800 (79.2) 3,500 (99.1) 2,800 (79.2) 3,000 (84.9) 4,000 (113.2) 5,000 (141.5) 6,000 (169.8) 7,000 (198.1)

0.20 3,150 (89.1) 4,200 (118.9) 5,250 (148.6) 4,200 (118.9) 4,500 (127.3) 6,000 (169.8) 7,500 (212.2) 9,000 (254.6) 10,500 (297.1)

0.10 6,300 (178.0) 8,400 (237.8) 10,500 (297.3) 8,400 (237.8) 9,000 (254.6) 12,000 (339.5) 15,000 (424.4) 18,000 (509.2) 21,000 (594.1)

0.00 NP NP NP NP NP NP NP NP NP

0LQLPXPGLPHQVLRQVRI‐LQPP

127(8VHDQ\RIWKHIROORZLQJFRPELQDWLRQVRIRSHQLQJV

$%&''()*

 0 LQLPXPRSHQLQJVL]HLVVTLQVTPPZLWK

PLQLPXPGLPHQVLRQVRI‐LQPP

0LQLPXPRI‐LQPPZKHQW\SH‐%YHQWLVXVHG

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere KeepRite Ofen Handbücher

KeepRite

KeepRite F9MAC Series Montageanleitung

Beliebte Ofen Handbücher anderer Marken

Armstrong

Armstrong EG7H SERIES Bedienungsanleitung

Payne

Payne PG92ESA Leitfaden

SUPREME

SUPREME FEM10-M2301CM-A Montageanleitung

Ingersoll-Rand

Ingersoll-Rand S9V2B080D4VSAC/D Montageanleitung

Johnson Controls

Johnson Controls TM9T Leitfaden

Fluke

Fluke 9118A Bedienungsanleitung

Lennox

Lennox EL195UHE Elite Series Installations- und Betriebshandbuch

Intertherm

Intertherm M7RL Series Bedienungsanleitung

HDG

HDG Pelletmaster 15 Bedienungsanleitung

Pinnacle

Pinnacle Aero Bella AB-716C-QH Handbuch

Nortek

Nortek MG2S Series Bedienungsanleitung

VERDER

VERDER CARBOLITE GERO ABF 8/28 Handbuch

Goodman

Goodman GMV9 Handbuch

SUPREME

SUPREME SUP10-M2301C Montageanleitung

Dettson

Dettson AMT400B34-SM1PMA Montageanleitung

Evcon

Evcon DGD 60 MBH Bedienungsanleitung

Trane

Trane S8B1A026M2PSAB Montageanleitung

Hart Sceintific

Hart Sceintific 9113 Bedienungsanleitung