Keis X900 Bedienungsanleitung
Keis Heated Clothing is istribute in the UK by
Motohaus Powersports Limited PO Box 7092 Hook RG29 1TY
In the interests of pro uct improvement we
reserve the right to make technical an
esign changes without notice.
www.keisapparel.co.uk
O P E R A T I N G I N S T R U C T I O N S
Heated appare for
outdoor activities
111
WARNING: To ensure safe operation follow these instructions
carefully and keep them in a safe place for future reference.
OUTER
HEATED
GLOVES
Visit
WWW.KEISAPPAREL.CO.UK
to see the full range of Keis Heated Apparel
and Accessories – All designed to
help you stay out longer!
TECHNICAL DATA
Material: Nylon and eather
Lining: 100% Polyester
V ltage: 12V only or Keis Battery Packs
Appr ximate Current Draw: (Pair) 1A
Typical P wer: 13W
H E A T E D A P P A R E L F O R O U T D O O R A C T I V I T I E S
DUAL
POWER
CARE OF YOUR KEIS HEATED OUTER GLOVES
I Do not wash.
I The regular application of a good quality textile proofer (e.g. SDoc100) is recommended.
X900
WARNING Extended periods of use in excess of one hour without hand movement is not
recommended and can cause skin irritation or even blistering. Always ensure that you maintain
regular hand movements during use.
Discontinue use immediately should either glove fail. Use of one glove only can limit your ability to
detect discomfort.
SAFETY & ENVIRONMENT FIRST
Do not dispose of electrical equipment with standard domestic waste.
Contact your local authority for disposal information specific to your area.
WARNING
IThis electrically heated garment must be used strictly in accordance with the
manufacturer’s instructions. Failure to observe this notice may lead to increased risk of
burns and fire resulting in injury or death.
ISwitch the garment off immediately and check the affected skin at any sign of irritation
or sensation of excessive heat.
INever leave the garment unattended when switched on.
IThis product is unsuitable for young children.
IDo not use this product if you suffer from: heightened or impaired temperature
sensitivity; an inability to sense temperature extremes; circulatory problems resulting
from diabetes or other medical conditions.
I Use this product with 12V systems ON Y, or Keis (optional) Battery Packs.
IAlways observe the correct fuse rating – see ‘Manage your Fuses’.
IDo not modify or disassemble any part of the system in any way.
+
–
Fused Connection ead
Glove Supply oom
OUTER
HEATED
GLOVES
PREPARING A VEHICLE TO POWER YOUR KEIS HEATED GARMENT
Your Keis heated gloves are designed to be powered from a 12V source such as a vehicle battery
or Keis Battery Packs.
To power your Keis garment from a vehicle battery attach the Fused Connection ead directly to the
battery or other live 12V source taking into account any safety notices issued by the vehicle
manufacturer and observing the polarity Red +ve and Black -ve.
Position the power socket so it is in a convenient position to power your garment and secure if necessary
using cable ties or tape ensuring that it cannot become trapped, damaged or interfere with the normal
operation of the vehicle.
WARNING Always connect the Red +ve lead to the battery first.
POWERING YOUR KEIS X900 HEATED OUTER GLOVES USING KEIS BATTERY PACKS
Your Keis X900 Heated Outer Gloves can be powered directly using the optional Keis Lithium Battery
Packs. Locate the zipped battery pocket inside the glove, install the battery and plug into the glove
socket.
NOTE: DO NOT pull the plug out by the cable.
Ask your dealer for details or visit www.keisapparel.co.uk.
POWERING YOUR KEIS HEATED OUTER GLOVES FROM OTHER KEIS
HEATED GARMENTS
Some models of Keis Heated Garments have dedicated power supply sockets for accessories so they
can share a single power source.
NOTE: In some cases additional supply leads may be required. Ask your dealer for details or visit
www.keisapparel.co.uk.
I Do not use if the product is visibly damaged.
MANAGE YOUR FUSES
WARNING For your safety it is essential to manage
the fusing to your eis Heated Apparel.
A selection of up to five fuses is supplied depending on
the current drain and potential combinations of the
garments.
On delivery the fuse holder in the supply loom may be
delivered without a fuse. To calculate the fuse value
required simply add the current draws for each of the
garments supplied by the 12V Supply Loom and use
the lowest rated fuse that exceeds the calculated
current.
NOTE: A fuse value below the value required may fail
in use.
FOR EXAMPLE: Sleeved Jacket consumes 7A, Insoles
consume 1.3A. Therefore total is 8.3A. Next fuse value
above this is 10A so use a 10A fuse.
POWERING YOUR KEIS GLOVES FROM A VEHICLE POWER SOURCE
Your eis heated gloves must be powered from the vehicle battery via the Fused Connection Lead as
installed above or the optional Cigarette Lighter/Accessory Plug. Ask your dealer for details or visit
www.keisapparel.co.uk.
TO OPERATE: Locate the 12v Supply Lead and simply connect or disconnect this to and
from the power source as required. An optional on/off switch is available.
Garme t Curre t
Draw
Outer Gloves
(Pair) 1.0A
Under Gloves
(Pair) 1.0A
Lo Power
Bodywarmer 1.5A
Hi Power
Bodywarmer 3.3A
Sleeved
Jacket 7A
Trousers 3.3A
Insoles (Pair) 1.3A
Fuses Colour
3A Purple
5A Tan
7.5A Brown
10A Red
15A Blue
NOTE: The potential
current drain when using
several garments can be
excessively high in some
situations. It is your
responsibility to ensure the
power source can provide
the current required in
such circumstances.
PREPARING THE GLOVES SUPPLY LOOM
Thread the Y-shaped Glove Supply oom through your jacket with one of each of the plugs that form
the top of the ‘Y’ positioned at the end of each arm and the remaining one protruding from the waist on
the side from which the power will be provided.
NOTE: The shorter of the two leads on the Glove Supply oom should be positioned on the side to
which you will connect the power. If you use the gloves on a regular basis consider using thread to tack
the Glove Supply oom into the lining of the jacket.
OPERATING THE INTEGRAL TEMPERATURE CONTROLLERS
When power is first supplied to the gloves the controller will flash red for 1 second.
TO OPERATE: Press and hold the Power Button for one second. The Controller will initialise on
Maximum power (Red). Briefly pressing the Power Button will cycle the temperature control through
‘Medium’ (Amber), ‘ ow’ (Green) and back to Maximum.
TO SWITCH OFF: Press and hold the Power Button for one second.
I Do not use if the gloves become wet inside.
X900
Andere Keis Motorradzubehör Handbücher
Beliebte Motorradzubehör Handbücher anderer Marken
SRC
SRC B-TRK502-01-01-SL Bedienungsanleitung
3M
3M Speedglas 9100 MP Bedienungsanleitung
hepco & becker
hepco & becker 6307520 00 01 Bedienungsanleitung
HOMCOM
HOMCOM AA0-077 Bedienungsanleitung
hepco & becker
hepco & becker 6307558 00 01 Bedienungsanleitung
Wunderkind Custom
Wunderkind Custom 106503-F15 Benutzerhandbuch
