Keith McMillen Instruments QuNexus Bedienungsanleitung
QuNexus Live Edit Mode Manual
QuNexus Version 1.0
May, 2013
Live Edit Mode is mainly intended for making quick edits on the fly. In Live Edit Mode you can
turn on and off Channel Rotation, change the MIDI output channel, transpose the keyboard, go
into CoMA mode, turn Channel Pressure and Poly After Touch on and off, set the bend range,
and send program change messages. It should be noted that these edits do not persist after
changing presets or unplugging QuNexus. Any Live Edits will affect Keyboard Layer only (not
Controller Layer). An illegal entry will just kick you out of Live Edit Mode but any legal entries
made prior to that will be kept.
To enter Live Edit Mode hold the Shift button for approximately two
and a half seconds until the blue LED on the Shift button turns on and
stays lit. To exit just press the Shift button again (you don’t have to
hold it down to exit).
When you first enter Live Edit Mode you might see that a few of the LEDs on the keyboard turn
on. This is because the ChnPres, AftTch, CC, and Rotate key buttons all display their state in
Live Edit Mode. All four of these are on in the image below:
These key buttons act as toggles as well to turn Channel Pressure, Poly After Touch, CCs, and
Channel Rotation on and off. Note that if you turn CCs off, all 3 possible CCs from Keyboard
Layer will not output unless you turn them back on.
1
The rest of the things you can do in Live Edit Mode are set up pretty much the same way. Listed
below is an outline of the basic steps to edit everything else. Following these steps you can find
information that is more specific to each function.
1. Hit the key button associated with what you wish to edit (see details below steps).
2. Use the -Oct+ buttons to increment or decrement to the desired number. The numbered
keys display what number you are on as you go.
a. Since the QuNexus keys only have number labels up to 12, numbers above 12 in
Live Edit Mode are displayed with a solid LED in the tens place and a blinking
LED in the ones place.
i. Example A: If 16, the LED on key 1 will be solid and the 6 key will blink.
ii. Example B: If 112, the LED on key 11 will be solid and the 2 key will blink.
3. Hit the associated button again to accept the edit and move on.
To set the Polyphony of the Channel Rotation function, use the “Notes” key with the steps
above. The polyphony is how many channels/keys can be used at one time when Channel
Rotation is on.
To Transpose the QuNexus, use the key labeled “Xpose” with the steps listed above. You can
go up or down 11 semitones. If you are below 0 the - Oct button will blink; if you are above 0 the
+ Oct button will blink.
2
To change the MIDI Output Channel number, use the key labeled “Channel” with the steps
listed on the previous page (shown below).
To set the Pitch Bend Range use the key labeled “Bend” with the steps listed on the previous
page (shown below). You can go from 0 to 12 semitones. If it is set to 0, Pitch Bend will be
disabled. The Bend Range will apply to the Bend Pad and also anything set to Pitch Bend in
Keyboard Layer.
To send Program Change messages you don’t have to hit a key button first. The current
Preset’s Program Change Number will be displayed when you first enter Live Edit Mode. Use
the -Oct+ buttons to increment or decrement to the desired Program Change. The messages
will output as you pass them.
3
CoMA Mode
Many DAWs and performance software tools like Ableton Live and Apple’s Logic have MIDI
Mapping modes that will recognize MIDI data from a controller and map it to whatever you
choose. Since the QuNexus can have multiple data sources outputting from one key, it is often
necessary to use the Controller Mapping Assistant (CoMA). CoMA mode allows quick mapping
of each available data source one at a time, enabling rapid and efficient software/controller
pairings.
CoMA Mode Mapping Guide
To enter CoMA Mode:
1. Hold down the Shift Button (for about two and a half seconds) until the Shift Button turns
blue and stays on. This puts you in Live Edit Mode.
2. Hit the key labeled “CoMA”.
Tap the Shift Button to exit CoMA Mode and go back to playing QuNexus normally.
CoMA will work differently depending on whether Channel Rotation is turned on. Channel
Rotation is turned on in the QuNexus Factory Preset C.
There are also a few differences when mapping MIDI from Keyboard Layer vs. Controller Layer.
Switch between Keyboard Layer and Controller Layer with the Togl button while in CoMA mode.
The CoMA key is solid blue for Keyboard Layer and blinks for Controller Layer. The CoMA Mode
key must be blue (or blinking blue) if you want to use the Togl button to switch between Layers.
4
Channel Rotation off:
Keyboard Layer
1. After entering CoMA Mode hit the desired
source button:
a. “Velo” button for note
b. “Pres” button for pressure
i. skip to step 3
c. “Tilt” button for tilt
i. skip to step 3
2. Hit the desired key to output a Note (use
octave buttons to switch octaves if necessary
for note mapping).
a. All keys in Keyboard Layer have the
same CC#s for Pressure or Tilt, so all
you need to do is press the source
button to output the MIDI message.
3. The key’s MIDI message will output.
4. If mapping multiple Notes, do so now just by
hitting the next key.
5. You can switch sources just by tapping the
button for the next source you want to map
(see step 1 and repeat).
Controller Layer
1. After entering CoMA Mode hit
the Togl A button to map
Controller Layer. The CoMA key
will flash blue.
2. Hit the desired source button:
a. “Velo” button for note
b. “Pres” button for pressure
c. “Tilt” button for tilt
3. Hit the desired key (octave
buttons don’t apply here
because MIDI in Controller Layer
doesn’t shift with the octave
buttons).
4. The key’s MIDI message will
output.
5. If mapping multiple notes or
CCs, do so now just by hitting
the next key.
6. You can switch sources just by
tapping the button for the next
source you want to map (see
step 2 and repeat).
5
Channel Rotation on:
Keyboard Layer
1. After entering CoMA Mode the Channel Key LED will be on, prompting you to enter the
Channel number you wish to assign. Select the Channel number using the -Oct+ buttons
to increment or decrement to the desired number. The numbered keys display what
number you are on as you go.
a. Since the QuNexus keys only have number labels up to 12, numbers above 12 in
Live Edit Mode are displayed with a solid LED in the tens place and a blinking
LED in the ones place.
i. Example: If 14, the LED on key 1 will be solid and the 4 key will blink.
2. Hit the Channel Key.
3. Hit the desired Source button:
a. “Velo” button for note
b. “Pres” button for Pressure
i. skip to step 5
c. “Tilt” button for Tilt
i. skip to step 5
4. Hit the desired key (use octave buttons to switch octaves if necessary for note mapping).
a. All keys in Keyboard Layer have the same CC#s for Pressure or Tilt, so all you
need to do is press the source button to output the MIDI message.
5. The key’s MIDI message will output.
6. If mapping multiple notes, do so now just by hitting the next key.
7. You can switch sources just by tapping the button for the next source you want to map
(see step 3 and repeat).
8. You can switch channels by holding down the Channel key for approximately 1 second
(see step 1 and repeat).
Controller Layer
Controller Layer does not rotate channels even when in Channel Rotation Mode so you can use
the steps for when Channel Rotation is off (see the previous page).
6
The Expression Pedal does not map in CoMA Mode unless Channel Rotation is on. This is
because the Expression Pedal can be mapped outside of CoMA Mode quite easily just by
stepping on it. When Channel Rotation is enabled the Expression pedal sends out on all active
Channels. If no keys are held down it will send out on the main starting Channel. If Channel
Rotation is on you can map it in CoMA Mode after selecting the Channel (after step 2 from
previous page). To map it push it on fully and then push it all the way off.
For Information about Keyboard Layer, Controller Layer, and Channel Rotation see the
QuNexus Quickstart Guide or the QuNexus Full Manual.
7
Andere Handbücher für QuNexus
3
Inhaltsverzeichnis
Andere Keith McMillen Instruments Controller Handbücher
