Kemppi FastCool 10 Technisches Handbuch

Fastcool 10

1906810E

0648

2 – Fastcool 10 / 0648 © kemppi oy

CONTENTS

1. PREFACE....................................................................................................................... 3

1.1. INTRODUCTION......................................................................................................... 3

1.2. PRODUCT INTRODUCTION ...................................................................................... 3

1.3. OPERATION SAFETY................................................................................................. 3

2. INSTALLATION.............................................................................................................. 4

2.1. REMOVAL FROM PACKAGING.................................................................................. 4

2.2. LOCATING THE MACHINE......................................................................................... 4

2.3. SERIAL NUMBER ....................................................................................................... 4

2.4. INSTALLATION AND MAIN PARTS ............................................................................ 4

2.4.1. ASSEMBLING THE EQUIPMENT.................................................................. 4

2.4.2. MAIN PARTS OF COOLING UNIT................................................................. 4

2.5. PREPARING FOR OPERATION ................................................................................. 5

3. OPERATION .................................................................................................................. 5

3.1. COOLER OPERATION ............................................................................................... 5

3.2. OVERHEAT SIGNAL LAMP ........................................................................................ 5

3.3. STORAGE ................................................................................................................... 5

4. MAINTENANCE............................................................................................................. 5

4.1. DAILY MAINTENANCE ............................................................................................... 6

4.2. EVERY SIXTH MONTHS ............................................................................................ 6

4.3. TROUBLE SHOOTING ............................................................................................... 6

5. dISPOSAL OF ThE MAChINE ..................................................................................... 6

6. TEChNICAL dATA ....................................................................................................... 7

7. TERMS OF GUARANTEE ............................................................................................. 7

Fastcool 10 / 0648 – 3© kemppi oy

1. PREFACE

1.1. INTROdUCTION

Congratulations on having purchased this product. Properly installed Kemppi products should

prove to be productive machines requiring maintenance at only regular intervals. This manual is

arranged to give you a good understanding of the equipment and its safe operation. It also contains

maintenance information and technical specications. Read this manual from front to back before

installing, operating or maintaining the equipment for the rst time. For further information on

Kemppi products please contact us or your nearest Kemppi distributor.

The specications and designs presented in this manual are subject to change without prior

notice.

In this document, for danger to life or injury the following symbol is used:

Read the warning texts carefully and follow the instructions. Please also study the Operation safety

instructions and respect them when installing, operating and servicing the machine.

1.2. PROdUCT INTROdUCTION

Fastcool 10 is a cooling unit designed for FastMig-welding equipment and to be used for cooling

welding gun. The operation of Fastcool is controlled by a microprocessor.

1.3. OPERATION SAFETy

Please study these Operation safety instructions and respect them when installing, operating and

servicing the machine.

Welding arc and spatters

Welding arc hurts unprotected eyes. Be careful also with reecting arc ash. Welding arc and

spatter burn unprotected skin. Use safety gloves and protective clothing.

Danger for re or explosion

Pay attention to re safety regulations. Remove ammable or explosive materials from welding

place. Always reserve sufcient re-ghting equipment on welding place. Be prepared for hazards

in special welding jobs, eg. for the danger of re or explosion when welding container type work

pieces. Note! Fire can break out from sparks even several hours after the welding work has been

nished!

Mains voltage

Never take welding machine inside a work piece (eg. container or truck). Do not place welding

machine on a wet surface. Always check cables before operating the machine. Change defect cables

without delay. Defect cables may cause an injury or set out a re. Connection cable must not be

compressed, it must not touch sharp edges or hot work pieces.

Welding power circuit

Isolate yourself by using proper protective clothing, do not wear wet clothing. Never work on a

wet surface or use defect cables. Do not put MIG-gun or welding cables on welding machine or

on other electric equipment. Do not press MIG-gun switch, if the gun is not directed towards a

work piece.

Welding fumes

Take care that there is sufcient ventilation during welding. Take special safety precautions when

welding metals which contain lead, cadmium, zinc, mercury or beryllium.

4 – Fastcool 10 / 0648 © kemppi oy

2. INSTALLATION

2.1. REMOvAL FROM PACkAGING

The equipment is packed in durable packages specially designed for them. Check the equipment

before taking it into use, to make sure that the equipment or a part of it have not got damaged

during the transportation. Also check that the delivery corresponds your order and that you have

received all the necessary instructions for installing and operating the equipment. The packaging

material can be recycled.

2.2. LOCATING ThE MAChINE

Place the machine on a horizontal, stable and clean ground. Protect the machine from heavy rain

and burning sunshine. Check that there is enough space for cooling air circulation in front of and

behind the machine.

2.3. SERIAL NUMbER

The serial number of the machine is marked on the machine CE-marking. Identicating the serial

number is the only proper means of maintaining and identifying parts for a specic product. It is

important to make correct reference to the serial number of the product when making repairs or

ordering spare parts.

2.4. INSTALLATION ANd MAIN PARTS

2.4.1. Assembling the equipment

The equipment is assembled in the following order:

1. Transport unit PM500 6185291

2. Cooling unit Fastcool 10 606810001

Assembly the transport unit according to the instructions in the package. Fasten the cooling unit

to the transport unit by using the screws and bolts delivered with the equipment.

2.4.2. Main parts of cooling unit

Back side

E Mains voltage connection cable

F Control cable

G Cooling water output hose

H Cooling water input hose

Front machine

A Housing

B Test switch

C Overheat control lamp

D Filling hole

Fastcool 10 / 0648 – 5© kemppi oy

2.5. PREPARING FOR OPERATION

Cooling liquid is injurious! Avoid also contact with skin or eyes. In case of injury,

seek for medical advice.

See also 2.4.2. Main parts of cooling unit.

1. Connect the mains voltage and control connectors of the cooler unit to the corresponding

connectors on the base of the power supply. The connection can be established through the

base of the power supply when the devices are separated or through the right side of the

FastMig 10 cooler by removing the right side plate.

2. Attach the power supply on the FastMig 10 cooler.

3. Connect the cooling water hoses with the wire feed unit, follow colour markings.

4. Fill the reservoir with a 40 - 20 % mixture of etanol and water, or with any other suitable

antifreeze agent. The capacity of the reservoir is 3 litres.

5. Switch on the power supply.

6. Press and hold down the test switch until the torch hoses are lled with liquid.

7. Device is ready to weld.

3. OPERATION

3.1. COOLER OPERATION

See also 2.4.2. Main parts of cooling unit

FastMig 10 Cooler operation is controlled by the microprocessor of the power supply. The cooler

pump starts to operate when the welding begins. After the welding has stopped, the pump will

operate 1 to 5 minutes longer depending on the welding time. During this time the liquid will cool

down to the surrounding temperature. If the pump is stopped, the need for maintenance of the

cooler will be reduced.

Check the tank liquid level regularly and ll in liquid, if necessary.

If the liquid ow is blocked, a hose is blocked or folded, or the container has ran out of liquid the

welding is stopped and error code, Err 5, appears on the FastMig panel.

3.2. OvERhEAT SIGNAL LAMP

The overheat signal lamp is lighting when temperature control of the machine has detected cooling

water overheat. The ventilator cools down the machine and when the lamp goes out welding can

be started again.

3.3. STORAGE

The machine must be stored in a clean and dry room. Protect the machine from rain and keep it

away from direct sunshine in places where temperature exceeds +25 °C. Check that there is free

space in front of and behind the machine for air circulation.

4. MAINTENANCE

Watch out for mains voltage when handling electric cables!

In planning product maintenance machine utilization degree and circumstances should be

considered. Careful use and preventive maintenance help to avoid unnecessary production

disturbances and breaks.

6 – Fastcool 10 / 0648 © kemppi oy

4.1. dAILy MAINTENANCE

The following maintenance opeations should be carried out daily:

• Check water level and input ow, add liquid if needed.

• Check cables and connections. Tighten, if necessary and replace defect parts

4.2. EvERy SIXTh MONThS

The following maintenance opeations should be carried out at least every sixth months:

• Clean off dust and dirt. Change the cooling liquid and wash up the pipes and water reservoir

with pure water.

• Check seals, cables and connections. Tighten, if necessary and replace defect parts.

4.3. TROUbLE ShOOTING

See also 3.2. Overheat signal lamp.

Overheat signal lamp is lit.

The unit is overheated.

• Check water circulation.

• Check that there is enough free space behind the machine for cooling air circulation.

Error code Err 5 on the FastMig panel

• Check the liquid hoses for damages.

• Remove any hose blockages.

• Check water circulation, add liquid if needed.

For further information and assistance, contact your nearest Kemppi service workshop.

5. dISPOSAL OF ThE MAChINE

Do not dispose of electrical equipment together with normal waste!

In observance of European Directive 2002/96/EC on Waste Electrical and Electronic

Equipment and its implementation in accordance with national law, electrical equipment

that has reached the end of its life must be collected separately and returned to an

environmentally compatible recycling facility. As the owner of the equipment, you should

get information on approved collection systems from our local representative.

By applying this European Directive you will improve the environment and human

health!

Fastcool 10 / 0648 – 7© kemppi oy

6. TEChNICAL dATA

Cooling unit

Connection voltage 24 V DC

Connection capacity 100 % ED 50 W

Cooling power 1 kW

Start pressure, max. 450 kPa

Cooling liquid 20% - 40 % etanol/water

Reservoir volume ca. 3 l

Overall dimension: length 570 mm

width 230 mm

height 280 mm

Weight 11 kg

Operating temperature range -20 … +40 °C

Storage temperature range -40 … +60 °C

Degree of protection IP 23 C

The products meet the conformity requirements of CE-marking.

7. TERMS OF GUARANTEE

Kemppi Oy provides a guarantee for products manufactured and sold by them if defects in

manufacture and materials occur. Guarantee repairs must be carried out only by an Authorised

Kemppi Service Agent. Packing, freight and insurance costs to be paid by orderer. The guarantee is

effected on the date of purchase. Verbal promises which do not comply with the terms of guarantee

are not binding on guarantor.

Limitations on guarantee

The following conditions are not covered under the terms of guarantee: defects due to natural wear

and tear, non-compliance with operating and maintenance instructions, connection to incorrect or

faulty supply voltage (including voltage surges outside equipment spec.), incorrect gas pressure,

overloading, transport or storage damage, re of damage due to natural causes i.e. lightning or

ooding.

This guarantee does not cover direct or indirect travelling costs, daily allowances or accommodation.

Note: Under the terms of guarantee, welding torches and their consumables, feeder drive rolls and

feeder guide tubes are not covered. Direct or indirect damage due to a defective product is not

covered under the guarantee. The guarantee is void if changes are made to the product without

approval of the manufacturer, or if repairs are carried out using non-approved spare parts.

The guarantee is also void if repairs are carried out by non-authorised agents.

Undertaking guarantee repairs

Guarantee defects must be informed to Kemppi or authorised Kemppi Service Agents within the

guarantee period. Before any guarantee work is undertaken, the customer must provide proof of

guarantee or proof of purchase, and serial number of the equipment in order to validate the guarantee.

The parts replaced under the terns of guarantee remain the property of Kemppi.

Following the guarantee repair, the guarantee of the machine or equipment, repaired or replaced,

will be continued to the end of the original guarantee period.

www.kemppi.com

Ver. 12

KEMPPI OY

PL 13

FIN-15801 LAHTI

FINLAND

Tel +358 3 899 11

Telefax +358 3 899 428

www.kemppi.com

KEMPPIKONEET OY

PL 13

FIN-15801 LAHTI

FINLAND

Tel +358 3 899 11

Telefax +358 3 734 8398

e-mail: myynti. @kemppi.com

KEMPPI SVERIGE AB

Box 717

S-194 27 UPPLANDS VÄSBY

SVERIGE

Tel +46 8 590 783 00

Telefax +46 8 590 823 94

e-mail: [email protected]

KEMPPI NORGE A/S

Postboks 2151, Postterminalen

N-3103 TØNSBERG

NORGE

Tel +47 33 346000

Telefax +47 33 346010

e-mail: [email protected]

KEMPPI DANMARK A/S

Literbuen 11

DK-2740 SKOVLUNDE

DANMARK

Tel +45 4494 1677

Telefax +45 4494 1536

e-mail:[email protected]

KEMPPI BENELUX B.V.

Postbus 5603

NL-4801 EA BREDA

NEDERLAND

Tel +31 765717750

Telefax +31 765716345

e-mail: [email protected]

KEMPPI (UK) Ltd

Martti Kemppi Building

Fraser Road

Priory Business Park

BEDFORD, MK443WH

ENGLAND

Tel +44 (0)845 6444201

Fax +44 (0)845 6444202

e-mail: [email protected]

KEMPPI FRANCE S.A.S.

65 Avenue de la Couronne des Prés

78681 EPONE CEDEX

FRANCE

Tel +33 1 30 90 04 40

Telefax +33 1 30 90 04 45

e-mail: [email protected]

KEMPPI GmbH

Otto-Hahn-Straße 14

D-35510 BUTZBACH

DEUTSCHLAND

Tel +49 6033 88 020

Telefax +49 6033 72 528

e-mail: [email protected]

KEMPPI SPOLKA z.o.o.

Ul. Piłsudskiego 2

05-091 ZĄBKI

POLAND

Tel +48 22 7816162

Telefax +48 22 7816505

e-mail: [email protected]

KEMPPI WELDING MACHINES

AUSTRALIA PTY LTD

P.O. Box 404 (2/58 Lancaster Street)

INGLEBURN NSW 2565

AUSTRALIA

Tel. +61 2 9605 9500

Telefax +61 2 9605 5999

e-mail: [email protected]

Kemppi OY LIMITADA

Av. Pdte. Edo. Frei Montalva 6001-81

Conchalí, SANTIAGO,

CHILE

Tel +56-2-949 1990

Telefax +56-2-949 1991

e-mail: [email protected]

OOO KEMPPI

Polkovaya str. 1, Building 6

127018 MOSCOW

RUSSIA

Tel +7 495 739 4304

Telefax +7 495 739 4305

e-mail: [email protected]

ООО КЕМППИ

ул. Полковая 1, строение 6

127018 Москва

Tel +7 495 739 4304

Telefax +7 495 739 4305

e-mail: [email protected]

Inhaltsverzeichnis

Andere Kemppi Schweißsystem Handbücher

Kemppi

Kemppi PRO EVOLUTION MXE Bedienungsanleitung

Kemppi

Kemppi MasterTig 325DC Bedienungsanleitung

Kemppi

Kemppi 220 Bedienungsanleitung

Kemppi

Kemppi A7 TIG Orbital System 300 Bedienungsanleitung

Kemppi

Kemppi MinarcTig 180 Bedienungsanleitung

Kemppi

Kemppi Kemppi A7 MIG Welder 350 Bedienungsanleitung

Kemppi

Kemppi Minarc 120 AU Bedienungsanleitung

Kemppi

Kemppi FastMig X 350 Bedienungsanleitung

Kemppi

Kemppi KEMPOMAT 161 Bedienungsanleitung

Kemppi

Kemppi Minarc 150 Bedienungsanleitung

Kemppi

Kemppi mastertig acdc 1600 Bedienungsanleitung

Kemppi

Kemppi Flexlite TX Bedienungsanleitung

Kemppi

Kemppi MXF 63 Bedienungsanleitung

Kemppi

Kemppi KEMPOMAT 320 KEMPOMAT 320C Bedienungsanleitung

Kemppi

Kemppi KEMPACT MIG 2520 Technisches Handbuch

Kemppi

Kemppi A7 350 Kurzanleitung zur Einrichtung

Kemppi

Kemppi FitWeld 300 Bedienungsanleitung

Kemppi

Kemppi M 420MV FastMig Bedienungsanleitung

Kemppi

Kemppi FastMig X 350MV Bedienungsanleitung

Kemppi

Kemppi 350 Bedienungsanleitung

Kemppi

Kemppi ArcFeed 200 Bedienungsanleitung

Kemppi

Kemppi Minarc Evo 150 Bedienungsanleitung

Kemppi

Kemppi HiArc M 400R Bedienungsanleitung

Kemppi

Kemppi M 420 Bedienungsanleitung

Beliebte Schweißsystem Handbücher anderer Marken

Berner

Berner PLASMACUT 54 Bedienungsanleitung

Pro Spot

Pro Spot PR-155 Bedienungsanleitung

Forney

Forney 210 Bedienungsanleitung

Thermal Arc

Thermal Arc 400S Bedienungsanleitung

Lincoln Electric

Lincoln Electric HANDYMIG 170I Bedienungsanleitung

GYS

GYS PROTIG 201 AC/DC Bedienungsanleitung

TAFA

TAFA 30*8B35 Bedienungsanleitung

Lincoln Electric

Lincoln Electric INVERTEC V350-PRO CE Bedienungsanleitung

ESAB

ESAB Buddy Arc 145 Bedienungsanleitung

CIGWELD

CIGWELD 636804 Kurzanleitung

Red-D-Arc

Red-D-Arc DC-400 Bedienungsanleitung

Hobart Welding Products

Hobart Welding Products Spool Gun DP 3035-10 Bedienungsanleitung

Elettro

Elettro HI-MIG 3000 SYNERGIC Bedienungsanleitung

WIA

WIA Weldmatic 270 CP132-2 Bedienungsanleitung

Sonics

Sonics H520T Bedienungsanleitung

Miller

Miller Big Blue 400D Bedienungsanleitung

NewArc

NewArc RT2000 Kurzanleitung

Hypertherm

Hypertherm powermax1000 Bedienungsanleitung