kenall LOW PROFILE SCONCE LPS SERIES Bedienungsanleitung
www.kenall.com |P: 800-4-Kenall |F: 262-891-9701 |10200 55th Street Kenosha, Wisconsin 53144, USA
This product complies with the Buy American Act: manufactured in the United Stateswith more than 50% of the component cost of US origin It may be covered by patents
found at www.kenall.com/patents.Content of specication sheets is subject to change; please consult www.kenall.com for current product details. ©2019 Kenall Mfg.Co.
1
INSTALLATION INSTRUCTIONS
LPS_F-5295_090418
IMPORTANT SAFEGUARDS
When using electrical equipment, basic safety precautions
should always be followed, including the following:
THIS PRODUCT MUST BE INSTALLED IN ACCORDANCE WITH THE
APPLICABLE INSTALLATION CODE BY A PERSON FAMILIAR WITH
THE CONSTRUCTION AND OPERATION OF THE PRODUCT AND
THE HAZARDS INVOLVED. DISCONNECT POWER TO ALL CIRCUITS
BEFORE WIRING FIXTURE. INSTALL IN ACCORDANCE WITH
ALL NATIONAL, STATE, AND LOCAL CODES. DO NOT CONNECT
TO AN UNGROUNDED SUPPLY. READ ALL FIXTURE MARKINGS
AND LABELS TO ENSURE CORRECT INSTALLATION OF FIXTURE.
SUPPLEMENTAL INSTRUCTIONS MAY BE LOCATED ON THE
FIXTURE, IN ADDITION TO THIS INSTRUCTION SHEET, REGARDING
ORIENTATION, OR MOUNTING RESTRICTIONS.
SAVE THESE INSTRUCTIONS
INSTALLATION INSTRUCTIONS
LPS SERIES –SEMI-RECESSED MOUNT –REMODEL CONSTRUCTION
LOW PROFILE SCONCE™
1. Back out screw(s) at bottom or side of housing
until baseplate can be easily removed.
2. Remove back-box.
Back-box
Screw
Back-box
3. Cut a rectangular hole on the wall
(recommended hole size 3-3/8" × 9").
4. Drill four (4) 5/16" holes. Use the back-box as a
template to mark pilot holes.
Wall
3.375
9.000
Cutout
Wall
2.000
9.750
5/16" Dia.
www.kenall.com |P: 800-4-Kenall |F: 262-891-9701 |10200 55th Street Kenosha, Wisconsin 53144, USA
This product complies with the Buy American Act: manufactured in the United Stateswith more than 50% of the component cost of US origin It may be covered by patents
found at www.kenall.com/patents.Content of specication sheets is subject to change; please consult www.kenall.com for current product details. ©2019 Kenall Mfg.Co.
2
INSTALLATION INSTRUCTIONS
LPS_F-5295_090418
5. Mount Back-box. Insert the back-box into the cutout making sure that the hooks are pointing up. Attach
back-box using 1/4-20 screws and nuts (supplied by others). Remove knockouts as needed.
Note: Remember to use non-ferrous hardware when installing MRI xtures.
Back-box
1/4 20 Screws
(supplied by others)
Back Mounting Bracket
Thumb Screw
Slide Bracket
6. Install back mounting brackets.
a-b. Insert back mounting bracket as shown below.
c. Slide bracket towards the wall and tight thumb screw.
d. Break metal tab by twisting it back-and-forth. Repeat these steps to install the second bracket.
www.kenall.com |P: 800-4-Kenall |F: 262-891-9701 |10200 55th Street Kenosha, Wisconsin 53144, USA
This product complies with the Buy American Act: manufactured in the United Stateswith more than 50% of the component cost of US origin It may be covered by patents
found at www.kenall.com/patents.Content of specication sheets is subject to change; please consult www.kenall.com for current product details. ©2019 Kenall Mfg.Co.
3
INSTALLATION INSTRUCTIONS
LPS_F-5295_090418
7. Make electrical connections. Disconnect facility power to the electric power supply leads. Connect xture leads
to power supply leads using connectors suitable for the gage and number of wires being used (not included).
MRI Fixtures:
a. Run the 24VDC supply from the EMI lter to the luminaire(s) using at least 18 AWG wires. Class 1 wiring is
required. Make sure wiring is completely enclosed in grounded conduit. Any gaps, regardless of size, must
be closed or wrapped in copper foil tape. Special attention should be paid to the wiring entry point into the
shielded space.
b. If a 0-10V dimmer is to be connected, install at this time. Dimmer must be installed outside the shielded
MRI environment with an intermediate MRI room EMI lter to the luminaires. Kenall recommends using
a Leviton® lllumaTech™ IP710 series dimmer or Grak Eye GRX-TVI control interface. Contact Kenall for
suitability of using an alternate sink-type 0-10V dimmer.
NOTES: To prevent MRI machine interference, all DC power and dimming signal wiring must be completely shielded
within grounded conduit.
8. Install xture. Top of housing over top of back-mounting-box's hooks.
9. Tighten screw at bottom of housing.
For technical assistance, call 1-800-4KENALL (1-800-453-6255).
CUSTOMER SERVICE
For warranty information visit www.kenall.com/Resources/Certied-Performance-Warranties
WARRANTY
Screw
Inhaltsverzeichnis
Andere kenall Arbeitsleuchte Handbücher
Beliebte Arbeitsleuchte Handbücher anderer Marken
PowerSmith
PowerSmith PWLD080T Bedienungsanleitung
MaxLite
MaxLite 73683 Bedienungsanleitung
Heitronic
Heitronic Trend 27867 Bedienungsanleitung
Monzana
Monzana Gore MZCL10 Bedienungsanleitung
EINHELL
EINHELL TE-CL 18/2000 LiAC Bedienungsanleitung
Bayco
Bayco NIGHTSTICK Dual-Light Xtreme Lumens... Bedienungsanleitung