Kenwood TM?D710 Bedienungsanleitung

Quick Guide for TM-D710

Knox County Radios

D710 Panel Showing the Default Configuration

General

The two sides of the display are termed Band A (left) and Band B (right). These have

nothing to do with the frequency bands. The D710 is set up so that packet (SARTrack

and RMS Express) work with Band A. Voice as well as data signals from the SignaLink

use Band B. This provides the ability to quickly move from voice to digital data (e.g.

NBEMS) without having to make any adjustments. If packet is not being used, Band A

can also be used for voice but not for data. The radio can listen on both bands

simultaneously but can only transmit on one band at a time.

The SignaLink cable connects to the data port at the back of the RF deck. This is the

mini-DIN socket beside the power leads. There is another mini-DIN socket beside this

one. This is only for programming the radio. The serial cable (PG-5G) for packet

connects to the rear-left of the radio’s control head.

The standard APRS frequency is 144.390. The 1200 baud Maine packet frequency is

145.010. The 1200 baud Knox County packet frequency is 433.100.

Pressing the round knob at the lower right of the control head sets the active voice

channel. This places the PTT on Band B. This is the default position.

Pressing the TNC button activates the internal TNC. This is to the right of the screen.

Repeated pressing will cycle through several other modes. If no mode display appears in

the window, the TNC is disabled and Band A may be used for voice.

The following sections describe the most commonly used adjustments. When ever the

radio is programmed to settings other than the default shown in the figure, the radio must

be returned to the default settings prior to shut down.

Change Frequency Band

Press [F] [Band Sel]. Each cycle will make one step through the series of bands.

Select Tone Frequency

Turn on Tone function by pressing TONE. Each press will step through the tone modes.

Press [F] [TONE].

Rotate Tuning control to select correct tone frequency.

Press any control other than [F] or [ESC] to set the frequency

To escape the selection function press [F] [ESC]

Store in Memory

Set up in VFO mode

Press [F]

Rotate tuning control to select desired channel

Press [MR] to save

To enter the Menu mode, press [F] followed by pressing the Tuning Knob.

To change the frequency step size, first get into the band on which you want to change

the step. press the left of right Band Select knob to select Band A or Band B, then press

[VFO]. Enter the Menu mode and access Menu 101. Rotate the tuning knob to select the

desired step.

Packet/APRS Set Up (Band A) – 1200 Baud

Note: At the time the computers, software and radios were initially configured, the

Toughbooks’ com ports (com 1) were set for 9600 baud communications. Some may

have been changed to 19,200 baud. If communications from COM 1 are not functioning,

check the laptop settings and those of RMS Express (packet session) and SARTrack. The

COM port settings of the D710 may be checked or changed, select AUX and menus 528

and 529 (pre-D710G) or 929 and 930 (D710G).

To activate the internal TNC, press the Band A Band Select Knob to make Band A

active.

Press [TNC] until you see PACKET12 in the Band A display. This is 1200 baud packet.

Enter VFO mode on Band A by pressing [VFO]. Set the frequency to 144.390 for APRS,

145.010 for the Maine packet frequency.

Data Operation (Band B): Sound Card Modes

When Fldigi or other sound card programs are used, the active Band will be Band B. This

is set up as the default.

APRS Set Up (Band A)

This uses the internal APRS capabilities of the radio; no computer required.

Turn the radio ON.

Press the “F” key to access the Setup Menu

Press the MHz knob (large tuning knob)

Turn the knob to select APRS

Press the knob again to enter the Menu Selection Mode

Basic Setting Menu #600

Enter your call sign with SSID

Set the Beacon Type to APRS

Turn the MHz knob to scroll through the menus

Internal TNC Menu #601

Do not make any changes. Leave all settings at “Default.” Be sure that 1200 Bps

(on air baud rate) is selected.

GPS Port Menu #602 (external GPS only)

Change the baud rate to match the GPS

Set the input to “GPS”

Set the Output to “Waypoint.”

Waypoint Format Menu #603

Set format to “Kenwood.”

Change NAME to “9-CHAR”

The Output setting should be set to “ALL”

Beacon Information Menu #606 (Mobile)

Speed setting should be turned ON

Altitude setting should be turned ON

Position Ambiguity should be turned OFF

Beacon TX Algorithm Menu #611

Set the Method to “Auto”

Internal GPS (G model only)

Press the “F” key to access the Setup Menu

Press the “GPS” key to toggle the GPS on or off.

Set Coordinates (Fixed Station)

Access Menu #627

Enter Position as ddmm’mm”

Digipeater

Access Menu #616, enable DIGIPEAT and RELAY

Cross Band Repeater Operation

Enter Menu mode and access Menu 403 (RPT.MOD).

Set the mode to CROSS BAND

Turn the power Off

Press [TONE] + Power ON. PTT and LOCK (key symbol) blink in the display.

To return to normal operation, turn power Off then press [TONE] + Power ON.

Andere Handbücher für TM?D710

Inhaltsverzeichnis

Andere Kenwood Radio Handbücher

Kenwood

Kenwood TK-6110 Bedienungsanleitung

Kenwood

Kenwood NX-5000 series Stücklistenhandbuch

Kenwood

Kenwood NEXEDGE NX-200 Bedienungsanleitung

Kenwood

Kenwood FleetSync TK-690 Bedienungsanleitung

Kenwood

Kenwood NEXEDGE NX-700 series Bedienungsanleitung

Kenwood

Kenwood TK-3180 Stücklistenhandbuch

Kenwood

Kenwood TK-7160 Bedienungsanleitung

Kenwood

Kenwood R-5000 Bedienungsanleitung

Kenwood

Kenwood ProTalk TK-3710 Bedienungsanleitung

Kenwood

Kenwood TK-8102H Bedienungsanleitung

Kenwood

Kenwood TM-732A Bedienungsanleitung

Kenwood

Kenwood CR-M30DAB Bedienungsanleitung

Kenwood

Kenwood NXR-5700 Bedienungsanleitung

Kenwood

Kenwood TK-3160-2-3 Bedienungsanleitung

Kenwood

Kenwood TS-850S Bedienungs- und Sicherheitshinweise

Kenwood

Kenwood NX-5700 Bedienungsanleitung

Kenwood

Kenwood TM-631A Bedienungsanleitung

Kenwood

Kenwood CR-ST100S Bedienungsanleitung

Kenwood

Kenwood TK-7360 Bedienungsanleitung

Kenwood

Kenwood TK-780 series Installationshandbuch

Kenwood

Kenwood NX-3200E3 Bedienungsanleitung

Kenwood

Kenwood TH-F6A Bedienungsanleitung

Kenwood

Kenwood TH-55AT/E Bedienungsanleitung

Kenwood

Kenwood TM-732A Bedienungsanleitung

Beliebte Radio Handbücher anderer Marken

EisSound

EisSound KBSound iSelect Bedienungsanleitung

Midland

Midland 1001LWX Bedienungsanleitung

Konig

Konig HAV-SR41 Bedienungsanleitung

Roberts

Roberts exprssion Bedienungsanleitung

VDigi

VDigi DD3.0 Bedienungsanleitung

Radio Shack

Radio Shack 21-1863 Bedienungsanleitung

Roberts

Roberts Stream 207 Bedienungsanleitung

Sony

Sony Walkman SRF-M97 Bedienungsanleitung

Stanley

Stanley FatMax FMC770 Bedienungsanleitung

auna

auna DAB-Radio 10026947 Bedienungsanleitung

SOUNDMASTER

SOUNDMASTER UR190 Bedienungsanleitung

HYT

HYT TC-320 Bedienungsanleitung

B-Tech

B-Tech GMRS-V2 Bedienungsanleitung

Weierwei

Weierwei VEV-V8 Bedienungsanleitung

SOUNDMASTER

SOUNDMASTER DAB750 Bedienungsanleitung

Telefunken

Telefunken TF-1505 Bedienungsanleitung

Makita

Makita LXRM03 Bedienungsanleitung

PRESIDENT

PRESIDENT TEDDY R. Bedienungsanleitung