KD-ZRC300 Remote Overview and Connections
TV ATV
CBX
BRP
L/S/H
ON OFF
AVR SEC
SELECT
DVR
GUIDE
EXIT
VOL
+
–
+
–
CH
MUTE
PREV CH
LIGHT
SHADES
HVAC
1 2 3
4 5 6
7 8 9
0
–
HEAT COOL
ZOOM AV PC
D
AM/FM INT RADIO SURR
MENU
A B C
AUTO
IR Light
The remote can be used for line-of-sight
IR control or as a Zigbee wireless
remote control
Indication Keys
Low Battery indicator: Power OFF LED
blinks every second while in active mode.
Battery Charging indicator: Power ON LED
blinks every second while in active mode.
Full Charge indicator: Both Power ON and
OFF LEDs blink every second while in
active mode.
Configuration Mode indicator: Both Power
ON and OFF LEDs are steadily illuminated
Device Keys
There are 7 device keys. The selected
Device Key LED will remain illuminated to
indicate which device is selected
Backlight
The backlight will turn on when movement
is detected and will stay on for five seconds
after movement has stopped
Function Keys
“A” + “1” Key: Sets configuration
mode through the RS-232 port on the
handheld remote
“A” + “2” Key: Sets configuration
mode through the Zigbee Receiver
“A” + “C” Key: To pair to ZigBee Receiver
“C” Key: To cancel any configuration
mode
System Modes
Idle Mode: Power Saving mode while
remote is not in use
Active Mode: Device switches to Active
Mode after a button is pressed or motion
is detected. It stays in Active Mode for
5 seconds.
Low Battery Mode: When the battery has
dropped below 2.4V the remote switches
to Low Battery Mode. Back lighting and
Configuration Mode are unavailable.
Configuration Mode: To setup and configure
the remote
Micro USB
Used to charge
the two 1.5v
rechargeable
Alkaline batteries
RS-232 Port
Used for configuring
the Zigbee remote.
Note: USB cable
must be connected
to micro USB
connector)
3.5mm Stereo
Phone Jack Pinout:
Tip: TxD, Ring: RxD,
Sleeve: Ground
Default Button Assignment
ON/OFF
Turns on / off selected device
TV Selection
Sets remote to control TV
Cable Box Selection (Switch)
Sets Cable Box as source for display
and remote will control Cable box
Blu-Ray Player Selection (Switch)
Sets Blu-ray Player as source for display
and remote will control Blu-Ray player
Audio/Video Receiver (Switch)
Sets AVR as source for display
and remote will control AVR
DVR & Guide
Used for Cable box commands
Light*
Sets remote mode to Lighting Control
Shades*
Sets remote mode to Shade control
Video Control Buttons
Rewind / Stop / Play (Pause) / Fast-forward
Function Button “A”
Programmable button
Defaults to Red / “A” button for cable boxes
Security Mode Selection
Remote will control Security
Light/Shade/HVAC Mode Selection
Remote mode is set to LSH.
MUST SELECT FROM
LIGHT / SHADE / HVAC below.
Control Arrows and Select
Navigates Up/Down/Left/Right
Selects current option
Exit
Exits current menu for selected source
Mute
Mutes selected source
Prev Ch
Switches back to Previous Channel
Volume (Up/Down)
Adjusts Volume for Selected Device Channel (Up/Down)
Adjusts Channel for Selected Device
HVAC*
Sets remote mode to HVAC Control
Numerical Buttons (0 to 9 + Enter)
Numbered buttons for general use
Function Button “B”
Programmable button. Defaults to
Green / “B” button for cable boxes.
Function Button “C”
Programmable button. Defaults to
Blue / “C” button for cable boxes
Heat
In HVAC, sets thermostat to Heat Mode
Apple TV (Switch)
Sets Apple TV as source for display
and remote will control Apple TV
Cool
In HVAC, sets thermostat to Cool Mode
AUTO (Function Button D)
In HVAC, sets thermostat to Auto Mode.
Defaults to Yellow / “D” button
for cable boxes.
*Must be preceded by L/S/H button press
4 5
KD-ZRC300_Manual.indd 4-5 8/20/14 2:43 PM
