Keysight Technologies M937 A Series Benutzerhandbuch

Startup Guide

Keysight M937xA PXIe

Vector Network Analyzer 

Modules

M9370A, 300 kHz to 4 GHz

M9371A, 300 kHz to 6.5 GHz

M9372A, 300 kHz to 9 GHz

M9373A, 300 kHz to 14 GHz

M9374A, 300 kHz to 20 GHz 

M9375A, 300 kHz to 26.5 GHz

Notices

No part of this manual may be

reproduced in any form or by any

means (including electronic storage

and retrieval or translation into a

foreign language) without prior

agreement and written consent from

Keysight Technologies, Inc. as

governed by United States and

international copyright laws.

Trademark Acknowledgments

Manual Part Number

M9370-90001

Print Date

September 5, 2014

Published in USA

Keysight Technologies Inc.

1400 Fountaingrove Parkway

Santa Rosa, CA 95403

Warranty

THE MATERIAL CONTAINED IN THIS

DOCUMENT IS PROVIDED “AS IS,”

AND IS SUBJECT TO BEING

CHANGED, WITHOUT NOTICE, IN

FUTURE EDITIONS. FURTHER, TO THE

MAXIMUM EXTENT PERMITTED BY

APPLICABLE LAW, KEYSIGHT

DISCLAIMS ALL WARRANTIES,

EITHER EXPRESS OR IMPLIED WITH

REGARD TO THIS MANUAL AND ANY

INFORMATION CONTAINED HEREIN,

INCLUDING BUT NOT LIMITED TO THE

IMPLIED WARRANTIES OF

MERCHANTABILITY AND FITNESS

FOR A PARTICULAR PURPOSE.

KEYSIGHT SHALL NOT BE LIABLE FOR

ERRORS OR FOR INCIDENTAL OR

CONSEQUENTIAL DAMAGES IN

CONNECTION WITH THE

FURNISHING, USE, OR

PERFORMANCE OF THIS DOCUMENT

OR ANY INFORMATION CONTAINED

HEREIN. SHOULD KEYSIGHT AND THE

USER HAVE A SEPARATE WRITTEN

AGREEMENT WITH WARRANTY

TERMS COVERING THE MATERIAL IN

THIS DOCUMENT THAT CONFLICT

WITH THESE TERMS, THE WARRANTY

TERMS IN THE SEPARATE

AGREEMENT WILL CONTROL.

Technology Licenses

The hard ware and/or software

described in this document are

furnished under a license and may be

used or copied only in accordance

with the terms of such license.

Restricted Rights Legend

If software is for use in the

performance of a U.S. Government

prime contract or subcontract,

Software is delivered and licensed as

“Commercial computer software” as

defined in DFAR 252.227-7014 (June

1995), or as a “commercial item” as

defined in FAR 2.101(a) or as

“Restricted computer software” as

defined in FAR 52.227-19 (June 1987)

or any equivalent agency regulation or

contract clause. Use, duplication or

disclosure of Software is subject to

Keysight Technologies’ standard

commercial license terms, and

non-DOD Departments and Agencies

of the U.S. Government will receive no

greater than Restricted Rights as

defined in FAR 52.227-19(c)(1-2)

(June 1987). U.S. Government users

will receive no greater than Limited

Rights as defined in FAR 52.227-14

(June 1987) or DFAR 252.227-7015

(b)(2) (November 1995), as applicable

in any technical data.

Safety Notices

CAUTION

A CAUTION notice denotes a hazard. It

calls attention to an operating

procedure, practice, or the like that, if

not correctly performed or adhered to,

could result in damage to the product

or loss of important data. Do not

proceed beyond a CAUTION notice

until the indicated conditions are fully

understood and met.

WARNING

A WARNING notice denotes a hazard.

It calls attention to an operating

procedure, practice, or the like that, if

not correctly performed or adhered to,

could result in personal injury or

death. Do not proceed beyond a

WARNING notice until the indicated

conditions are fully understood and

met.

Contents

1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Getting Started

Introduction 5

Related Documentation

You can find all M937xA PXI network analyzer module documentation and

other resources at: http://na.support.keysight.com/pxi/help 

or at the respective product pages on www.keysight.com (go to Document

Library > Manuals).

Getting Started

STEP 1. Unpack and Inspect the Network Analyzer Modules

CAUTION The network analyzer modules are shipped in materials which prevent damage

from static. The modules should only be removed from the packaging in an

anti-static area ensuring that correct anti-static precautions are taken. Store

all modules in anti-static envelopes when not in use.

Electrostatic discharge (ESD) can damage or destroy electronic components.

Use a static-safe work station to perform all work on electronic assemblies.

Figure 1-1 shows a static-safe work station using two types of ESD protection:

conductive table-mat and wrist-strap combination, and conductive floor-mat

and heel-strap combination. Both types, when used together, provide a

significant level of ESD protection. Of the two, only the table-mat and

wrist-strap combination provides adequate ESD protection when used alone.

To ensure user safety, the static-safe accessories must provide at least 1

meg-ohm of isolation from ground.

WARNING Do NOT use these techniques for a static-safe work station when working on

circuitry with a voltage potential greater than 500 volts.

Figure 1-1 ESD protection setup

Getting Started

STEP 1. Unpack and Inspect the Network Analyzer Modules

Unpack the network analyzer modules from the shipping containers. Keep the

black and red plastic port protectors and the shipping containers for possible

reuse.

Inspect for Damage

After unpacking a network analyzer module, inspect it for any shipping

damage. Report any damage to the shipping agent immediately, as such

damage is not covered by the warranty.

CAUTION To avoid damage when handling the network analyzer modules, do not touch

exposed connector pins.

How to Return an Instrument for Service

Should it become necessary to return a network analyzer module for repair or

service, follow the steps below:

1. Review the warranty information shipped with your product.

2. Contact Keysight to obtain a Return Material Authorization (RMA) and

return address. For assistance finding Keysight contact information, go to

www.keysight.com/find/assist (worldwide contact information for repair

and service).

3. Write the following information on a tag and attach it to the network

analyzer module:

• Name and address of owner. A P.O. box is not acceptable as a return

address.

• Network analyzer module serial numbers. The serial number label is

located on the side panel of the module. The serial number can also be

read from the Soft Front Panel (SFP) interface, after the hardware is

installed.

• Description of the service required or the failure.

4. On the shipping label, write ATTENTION REPAIR DEPARTMENT and the

RMA number.

5. Ship the analyzer module using the original packaging materials. Shipping

the analyzer module in anything other than the original packaging may

result in non-warranted damage.

NOTE In your correspondence, refer to the network analyzer module by serial number

and by model number.

Getting Started

STEP 2. Check the Shipment

Use the Contents List in the shipping container to verify the completeness of

your shipment. If not complete, refer to “Contacting Keysight” on page 25.

Getting Started

STEP 3. Install the Software

System Requirements

Hardware Requirements

Topic Windows 7 and Vista Requirements

Operating system Windows 7 (32 bit and 64 bit)

Windows Vista, SP 1 and SP2 (32-bit and 64-bit)

Processor speed 1.5 GHz dual core (x86 or x64) minimum

(2.4 GHz recommended)

Available memory 1 GB minimum (8 GB recommended)

Available disk space 1.5 GB available hard disk space

Topic Requirements

Chassis PXIe or PXI-H chassis slot

Controllers PXI or PXI Express embedded controller or remote controller

(external PC connected to the chassis by a PCI-to-PXI

interface) is required.

Embedded controller Keysight M903xA or an equivalent embedded controller that

meets the following requirements:

•A PXIe system controller (PXI-1 embedded controllers

are not compatible).

• Utilizes a 2x8, 4x4, or 1x8 PXIe system slot link

configuration.

•Runs one of the operating systems listed in System

Requirements (above).

Remote controller (For Keysight M9018A chassis use only) A PC running one of

the operating systems listed in System Requirements

and a Keysight M9021A Cable Interface x8 with one of the

following PC interface options:

•Keysight M9045B PCIe ExpressCard Adaptor x1, with

cable (for a laptop PC)

•Keysight M9048B PCIe Desktop Adaptor x8, with cable

(for a desktop PC)

Getting Started

STEP 3. Install the Software

Power Up the Controller

If you are using a remote controller, complete the following steps:

1. Install the cable interface between the remote controller and the chassis. If

you are using an Keysight M9021A cable interface, refer to the Keysight

M9021A documentation for further details.

2. Power up the chassis.

3. Power up the PC.

CAUTION If you are using a remote controller and you have installed the interface cable, you must

power up the chassis BEFORE you power up the PC.

When you power down your system, shut down the PC BEFORE you power down the

chassis.

If you are using an embedded controller, complete the following steps:

1. Install the embedded controller module into a compatible chassis. The

Keysight M9018A PXIe chassis is recommended. Refer to the Keysight

M9018A documentation for further details.

2. Connect peripherals (mouse, keyboard, monitor).

3. Power up the chassis.

Software Installation Overview

The software installation includes the following items:

• Keysight IO Libraries Suite (IOLS), which includes the Keysight Connection

Expert. This software is included with your shipment (CD part number

E2094-60003), and the latest version is available at

www.keysight.com/find/iosuite. This software must be installed first.

NOTE Version 16.3.17914.4 (or newer) of the Keysight IO Libraries Suite is required.

• Network analyzer module software, which includes the soft front panel

(SFP) software, device drivers (IVI-C and IVI-COM, and LabVIEW G), and

documentation for the M937xA PXIe Vector Network Analyzer modules.

This software is included with your shipment (CD part number

M9370-90003) and is also available at

http://na.support.keysight.com/pxi/firmware.

Andere Handbücher für M937 A Series

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Keysight Technologies Steuereinheit Handbücher

Keysight Technologies

Keysight Technologies J7211A Service-Handbuch

Keysight Technologies

Keysight Technologies J7201A Service-Handbuch

Keysight Technologies

Keysight Technologies N3301A Betriebsanleitung

Keysight Technologies

Keysight Technologies U9422A Bedienungsanleitung

Keysight Technologies

Keysight Technologies M9168C Bedienungsanleitung

Keysight Technologies

Keysight Technologies 8494 Service-Handbuch

Keysight Technologies

Keysight Technologies M9195A PXIe Benutzerhandbuch

Keysight Technologies

Keysight Technologies 34946A Bedienungsanleitung

Keysight Technologies

Keysight Technologies 34952A Bedienungsanleitung

Keysight Technologies

Keysight Technologies M9170A Bedienungsanleitung

Keysight Technologies

Keysight Technologies M937A Series Bedienungsanleitung

Keysight Technologies

Keysight Technologies M9195A PXIe Benutzerhandbuch

Keysight Technologies

Keysight Technologies 81610A Bedienungsanleitung

Keysight Technologies

Keysight Technologies 81618A Bedienungsanleitung

Keysight Technologies

Keysight Technologies 8498A Service-Handbuch

Keysight Technologies

Keysight Technologies 34946A Bedienungsanleitung

Keysight Technologies

Keysight Technologies 81625B Bedienungsanleitung

Keysight Technologies

Keysight Technologies J7204A Service-Handbuch

Keysight Technologies

Keysight Technologies M9101A Betriebsanleitung

Keysight Technologies

Keysight Technologies E1465A Bedienungsanleitung

Keysight Technologies

Keysight Technologies J-BERT M8020A Betriebsanleitung

Keysight Technologies

Keysight Technologies 85091D Bedienungsanleitung

Keysight Technologies

Keysight Technologies 8495D Service-Handbuch

Keysight Technologies

Keysight Technologies 34950A Bedienungsanleitung

Beliebte Steuereinheit Handbücher anderer Marken

Festo

Festo Compact Performance CP-FB6-E Stücklistenhandbuch

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Bedienungsanleitung

JS Automation

JS Automation MPC3034A Bedienungsanleitung

JAUDT

JAUDT SW GII 6406 Series Kurzanleitung

Spektrum

Spektrum Air Module System Bedienungsanleitung

BOC Edwards

BOC Edwards Q Series Bedienungsanleitung

KHADAS

KHADAS BT Magic Bedienungsanleitung

Etherma

Etherma eNEXHO-IL Bedienungsanleitung

PMFoundations

PMFoundations Attenuverter Bedienungsanleitung

GEA

GEA VARIVENT Bedienungsanleitung

Walther Systemtechnik

Walther Systemtechnik VMS-05 Bedienungsanleitung

Altronix

Altronix LINQ8PD Montageanleitung

Eaton

Eaton Powerware Series Bedienungsanleitung

WAGO

WAGO 750-407/040-000 Bedienungsanleitung

Sony

Sony CCU-590 Bedienungsanleitung

Graco

Graco 25D614 Bedienungsanleitung

Task Force Tips

Task Force Tips YE-RF-900 Programmierhandbuch

Shini

Shini SPV-U Series Bedienungsanleitung