KHE AUDIO ELECTRONICS ACS Series Bedienungsanleitung

V1.0 2020-05-08 www.KHE-AudioElectronics.com
KHE AUDIO ELECTRONICS
AMPLIFIER CABINET SELECTOR
ACS – Series
A Switching-System for Guitar Amplifiers, Speaker
Cabinets and Load Boxes.
"... focus on your sound and creativity, instead of wasting your time with
plugging cables and waiting for amps to heat-up!"
IMPORTANT: READ THIS MANUAL BEFORE USING THE SWITCHER !
USER MANUAL

KHE ACS SERIES – USER MANUAL www.KHE-AudioElectronics.com 2 / 23
For reasons of the product liability, we are obligated to make clear certain safety aspects which must not be
ignored under any circumstances:
- Read, retain, and follow all instructions. Heed all warnings.
- To prevent damage, fire or shock hazard, do not expose this unit to rain or moisture. Do not use this
product near water or any other liquids.
- This product should be located away from heat sources such as radiators, heat registers, etc.
- Unplug the power supply before cleaning the unit exterior. Use a dry cloth only. Wait until the unit is
completely dry before reconnecting it to the power supply.
- Maintain unobstructed air space behind and above the unit for proper ventilation and cooling.
- Protect the power supply and all attached cables from being pinched or abraded.
- The power supply of this product should be unplugged from the outlet when left unused for a long
period of time or during storm weather.
- Use only the power supply supplied with the unit.
- Install in accordance with the manufacturer's instructions
- Keep these instructions for future reference.
CAUTION: If the unit becomes physically damaged due to dropping or for other reasons, it should be returned
to the factory for repair to avoid the risk of further damage to the unit or to attached units. No user serviceable
parts inside. Warranty is void if device gets modifyed by unauthorized personal. In case of malfunction or
mechanical damages, please contact KHE Audio Electronics for further assistance.
By purchasing and using this product, you clearly understand that you are taking full responsibility for the use
of this product.
KHE Audio Electronics accepts no responsibility (consequential or inconsequential) for damage or injury caused
by improper connections, improperly grounded amplifiers, user error, or injury caused by failure of the ACS or
any component inside the ACS. Use of the ACS implies that the owner/user clearly understands and agrees to
all of the terms stated within this user manual, has decided to use the ACS under these terms, accepts full
responsibility for any damage or injury, and waives his/her rights to a liability claim against KHE Audio
Electronics (or associated companies or directors) for any damage or injury caused while using the ACS. As it
is impossible for KHE Audio Electronics to ensure the user is following these instructions, the user must take
full responsibility in the suitability of purchasing a KHE product for his or her use.
The device serves for routing guitar and amplifier signals as well as for controlling amplifiers, speaker cabinets
and load boxes, and must be used exclusively for this purpose.
KHE AUDIO ELECTRONICS IS NOT RESPONSIBLE FOR ANY DAMAGE TO YOUR AMPLIFIER THAT MAY OCCUR IN
CONNECTION WITH ANY USE OF THE ACS.
SAFTEY PRECAUTIONS
WARNING & LIABILITY NOTICE

KHE ACS SERIES – USER MANUAL www.KHE-AudioElectronics.com 3 / 23
Congratulations on your purchase of a KHE Amplifier Cabinet Selector !
The KHE ACS is a switching and routing system for guitar amplifiers, speaker cabinets and load boxes.
Connect them to the ACS, power them up, and you are ready to go : Switch and play between all
your amps, speakers and loadboxes by a single push of a button. Use stompboxes like boosts and
overdrives with all amplifiers, and share effect pedals like delays or gates in the fx-loops of all
amplifiers. No need to interrupt or stop playing - switch all amps and cabs on the fly !
The KHE ACS-Series is the ultimate solution for any situation where more than one amp or cab is
available : recording studios, reampers & profilers, gear enthusiasts & collectors, music stores &
showrooms, amp manufacturers, repair shops, gear reviews & comparisons and live musicians.
The KHE ACS-Series features an extensive product line-up with a total of 7 different switchers,
providing the perfect switching configuration for any kind of setup or application. All switchers can
be dasy-chained and linked together to create the most flexible switching system possible. This
manual covers all 7 switchers and their use, functions and features.
To take advantages of all the features that have been implemented into the ACS, please take your
time to read through this manual before you use the switcher. If you have any questions that are not
answered in this manual, please refer to the FAQ section on our website. If you have any questions
or feedback, please contact us at info@khe-audioelectronics.com .
RULES OF OPERATION
NEVER change cable wiring while ACS, amps or load boxes are powerd ON.
NEVER unplug any connections of an amplifier that is connected to the ACS while the amplifier is on.
NEVER unplug the amplifier input cable and never plug the guitar cable straight in the amp input.
NEVER exceed the maximum amplifier & load power rating.
NEVER unplug a power attenuator in the power attenuator insert while the ACS is ON.
ALWAYS power-on the ACS before the connected equipment.
BE CAREFUL when using built-in time-based effects in amps like reverb or delay. Always make sure to either
A) turn the effect pedal off before disableing or changing an amp or
B) let the effect completely ring out before disabeling / changing the amp.
These rules also apply to permanentely connected effect pedals in the fx-loop of a single amplifier.
Ignoring these rules can damage the ACS or the connected equipment.
INTRODUCTION

KHE ACS SERIES – USER MANUAL www.KHE-AudioElectronics.com 4 / 23
Controls & Display 5
Guitar Input 6
Amplifier Switching 6
Cabinet & Load Switching 7
Attenuator Insert 8
FX-Loop Switching 9
Tuner Output 10
Re-Amping 10
Ground Lift 10
Recall Mode 10
Setup Procedure 11
ACS 4x2 12
ACS 4x4 12
ACS 4x4 FX 12
ACS 8x4 12
ASX 8 13
CSX 8 13
AFX 8 14
Feature List 14
MIDI Control 15
Link Mode 16
Link Mode – Setup Examples 18
Setup Menu 19
Things To Know 20
Technical Specifications 22
Warranty 22
Declaraction Of Conformity 23
TABLE OF CONTENT

KHE ACS SERIES – USER MANUAL www.KHE-AudioElectronics.com 5 / 23
AMPLIFIER SWITCHES
Switches to enable, disable or change amplifiers. No need to disable an amplifier before activating a different
one – the ACS manages the complete switching procedure! Amplifiers can not be enabled if no cabinet is
activated. All amplifiers are protected by an internal load resistor. The leds shows the current status:
RED: Amplifier activated
OFF: Amplifier deactivated
CABINET SWITCHES
Switches to enable, disable and change cabinets and loads. Up to 2 load devices can be activated in parallel
Cabinet jacks are supervised for a speaker cabinet or load box. Unused cabinet jacks are automatically excluded
and locked from the switching operation, so amps can never be switched to an unused cabinet jack. In case a
cabinet gets deactivated while an amp is still on, the ACS will disable the activated amp automatically before
removing the load. The leds shows the current status of the cabinet output:
RED: Cabinet activated
DIM: Cabinet deactivated
OFF: no load connected
FX SWITCH
Switches to bypass or activate connected fx-loops and effect pedals. The state of the fx-loop gets saved and
recalled automatically when switching amplifiers. The leds shows the current status of the fx-loop:
RED: FX-Loop activated
OFF: FX-Loop deactivated
CTRL SWITCH
Switch to control System Functions & Midi Settings. The leds shows the current status of the ACS:
RED: Standalone Mode
GREEN: Link Mode
OFF: Power Off
RED / GREEN, blinking: Link Mode – Setup Error
RED, blinking: MIDI PC – Preset Changed
ORANGE, blinking: System Error
POWER SWITCH
Switch to power on the ACS. Amplifiers are always protected by an internal load resistor, even when the
power-switch is off.
CONTROLS & DISPLAY

KHE ACS SERIES – USER MANUAL www.KHE-AudioElectronics.com 6 / 23
The KHE Amp Switchers features two guitar inputs, one on the
front panel and one on the rear panel. The front input has
higher priority than the rear input.
The KHE ACS guitar input works perfectly with reamping boxes,
stomboxes like overdrives, boosts and distortions and effect
pedals like delays or reverb.
The KHE Amp Switchers let you switch between mono guitar amplifiers. Instantly, by the single push of a
button. No need to stop or interrupt playing. The signal path of the ACS is completely transparent and
extremely low-noise. It does not color the sound of your amplifiers in any way.
WIRING
Connect the guitar inputs of the amplifier to the black AMP INPUT jacks.
Use high-quality shielded unbalanced instrument cables only.
Connect the speaker outputs of the amplifier to the blue AMP OUTPUT jacks.
Use high-quality speaker cable only (we recommend 1,5mm2).
NOTES
The KHE ACS is compatible with any kind of mono amplifier, up to 150 watts per channel :
Tube, solid-state, (bridged) class-d, heads and xombos.
Amplifiers can not be activated if no cabinet ouput is activated.
All amplifiers are protected by an internal load resistor and the unused amps are muted at their input,
so no singals can reach the power amp.
A special mute circuit removes all switching noise like clicks and pops - switching between amps or
loads is more silent than most amps channel switching!
GUITAR INPUT
AMPLIFIER SWITCHING

KHE ACS SERIES – USER MANUAL www.KHE-AudioElectronics.com 7 / 23
The KHE Amp Switchers let you switch between load devices like speaker cabinets and load boxes. Instantly by
the single push of a button. No need to stop or interrupt playing.
WIRING
Connect the load devices to the red CABINET jacks.
Use high-quality speaker cable only (we recommend 1,5mm2).
Once a load gets connected, the corresponding LED on the front panel will light up in a dimmed red
state. This indicates a load got detected and the output can now be activated.
NOTES
The KHE ACS is compatible with any kind of load device up to 150 Watts per channel :
Speaker Cabinets, reactive and resistive Load Boxes, active Load Boxes and Combo Speakers.
The Dual Cab Mode lets you activate and play two speaker cabinets or load boxes in parallel.
Activate the Dual Cab Mode by entering the SETUP MENU and push AMP-SWITCH 2. See « SETUP
MENU » for more details.
The load switching is completly passive with no active components. High-quality relays were used for
the switching procedure.
CABINET & LOAD SWITCHING

KHE ACS SERIES – USER MANUAL www.KHE-AudioElectronics.com 8 / 23
The Attenuator Insert is an post-amplifier pre-speaker insert loop. It lets you use an power attenuator across all
amps and attenuate the volume of all amps simuntaneously, and switch the attenuated output signal to all
connected cabinets or loads. The Attenuator Insert feautre is disabled by default (both S-LINE send and S-LINE
jacks are wired in parallel). By activating the Attenuator Insert Loop, the parallel connection of these jacks will
be removed so they can be used as a serial insert loop.
WIRING & SETUP
To activate the Attenuator Insert, follow this setup procedure:
1) Turn off the ACS and all amps and attenuators.
2) Connect the Input of the Attenuator to the white S-LINE SEND jack of the ACS. This connection sends
the speaker-signal from the amplifier to the input of the power attenuator device.
3) Connect the Output of the Attenuator to the white S-LINE RETURN jack of the ACS. This connection
sends the attenuated speaker signal back to the ACS to be switched to a speaker cabinet.
4) Power on the ACS and activate the Attenuator Insert funtion by entering the SETUP MENU and push
AMP-SWITCH 4. In case no attenuator is connected, the insert loop won’t be activated (AMP-LED 4
will blink four times). See « SETUP MENU » for more details. Don’t miss this step!
WARNING
Connecting an attenuator without having the Attenuator Insert activated may damage your amps
and attenuators!
Never change the wiring of the S-Line Jacks while the ACS, the attenuator and the amps are powerd
on! Removing the connected attenuator while the ACS is on can lead to no-load scenarios !
When using active attenuators, such as Boss Waza TAX, make sure to power-on the ACS before the
attenuator or turn the ouput volume down while the ACS is powerd off. Otherwhise oscillations
may happen on the attenuator.
NOTES
The KHE ACS is compatible with all type of attenuators : Boss Waza Tube Expander, UA OX Top Box,
Palmer Power Pad, SPL Reducer, Harley Benton PA-100, Bugera PS1, TAD Silencer, Jet City Attenuator,
Weber Attenuators, Koch Attenuators, THD Hotplate, Rivera Attenuators and many more.
ATTENUATOR INSERT

KHE ACS SERIES – USER MANUAL www.KHE-AudioElectronics.com 9 / 23
Like the cabinet jacks, the Attenuator Insert gets supervised for a proper load. If no attenuator is
connected, it wont get activated (error shown by 5x blinking the Amp4-Led).
The state of the attenuator insert function gets saved and recalled when powering up the ACS.
When linking multiple ACS together, the Attenuator Insert feature will be limited, as the S-LINE jacks
will used for the linking of the speaker lines. If you want to use the Attenuator Insert in Link Mode,
shoot us a message to discuss setup possibilities.
The FX-LOOP SWITCHING is an optional feature for the KHE ACS:
Route your pedal board and all the amplifiers fx-loops thru the ACS and share effect pedals like delays, gates,
reverb, chorus, eq and multi-fx pedals with all amps. You can even hook up a dedicated pedal-switching system
and create the most flexible setup possible.
CONTROL
The FX-Loops can be true-bypassed on the ACS: Push the FX button on the frontpanel short to toggle the FX
state. The ON/OFF state gets saved and automatically recalled when switching amps. All fx-switching functions
can be controlled via MIDI.
WIRING: FX-Loop
Connect the fx-send jack of the amplifiers to the black FX-LOOP SEND jacks of the ACS.
Connect the fx-return jack of the amplifiers to the black FX-LOOP RETURN jacks of the ACS
WIRING: Effect Pedals
Connect the input jack of the effect pedals to the black FX-INPUT jack of the ACS.
Connect the output jack of the effects pedals to the black FX-OUTPUT jack of the ACS.
NOTES
Proper gain-staging of the amps is very important when using delay pedals: make sure all the amps
send a similar signal level out of the fx-loop send. Otherwise, there is a change of nasty sounds while
switching amps, because of the different signal levels saved in the delay. This is highly dependent on
FX-LOOP SWITCHING

KHE ACS SERIES – USER MANUAL www.KHE-AudioElectronics.com 10 / 23
the construction of the amp (channel-volume, master volume, fx-level) and probably needs some trial
and error.
Clean power sources & wiring is needed to make the fx-loop switching work without noise, hum, or
clicking.
Gates in the fx-loops can be side-chained from the tuner output of the ACS. Make sure to use a
isolated power-source with only the gate powerd by this power output. Depending on the gate circuit,
this may can cause a slight hum (ground-loop). If this is the case, it’s best to use an isolation
transformer at the key-input to remove any ground-loops.
When setting everything up, start small with only 1 pedal, test, add another pedal, test, and so on.
This way it’s easy to identify problems with wiring / pedals / power sources.
The switching path is completly passive with no active components in the signal path. High-quality
relays were used for the switching procedure.
The FX-Loop switching feature does not add fx-loops to amplifiers without one!
The TUNER OUTPUT lets you feed a guitar tuner in parallel to the input signal. The buffered input signal is
always present at the tuner output jack.
The tuner output can also be used to record a clean di-track of your guitar, simultaneously to the amplified
track. The tuner output can also be used to side-chain a key input of a gate pedal in the fx-loops of the
amplifiers.
The KHE ACS plays very nicely along with re-amping setups. Connect the DI output signal from your DAW to the
GUITAR INPUT on the rear of the ACS by a reamping box to feed your entire amp collection. You can override
and disable the rear input signal by plugging in the guitar directly into the front guitar input of the ACS.
The GROUND LIFT helps to eliminate hum and buzz from sub-optimal grounding schemes.
Activate the GROUND LIFT by entering the SETUP MENU and push AMP-SWITCH 3. See « SETUP
MENU » for more details.
In case ground loops occur, NEVER defeat or remove or an amplifiers safety ground, PROTECTIVE EARTH,
which is provided by the 3-prong AC power-cord plug! Doing so may not only be ILLEGAL, but it may also
pose a SHOCK or ELECTROCUTION HAZARD.
The RECALL MODE automatically loads the last activated configuration on start-up of the ACS.
Activate the RECALL MODE by entering the SETUP MENU and push AMP-SWITCH 1. See « SETUP MENU » for
more details.
In case a configuration cannot be loaded (due missing or removed cabinet), the amplifier won’t be
enabled. The Recall Mode gets deactivead automatically once the LINK MODE gets activated.
TUNER OUTPUT
RE-AMPING
GROUND LIFT
RECALL MODE
Dieses Handbuch passt für folgende Modelle
7
Inhaltsverzeichnis
Andere KHE AUDIO ELECTRONICS Schalten Handbücher


















