Kicker 19417166 Bedienungsanleitung

19417166-20190620

19417166

Designed for 2019 and newer

Chevrolet® Silverado 1500

and GMC® Sierra 1500 Crew

Cab or Double Cab trucks with

HD radio.

Subwoofer Harness

Subwoofer Assembly

Amplifier Assembly

Subwoofer Power Harness

Amplifier Power Harness

M6 Nuts x 3

Wire Ties x 6

Fuse x 2

Adaptor Harness

Self-Drilling Screws x 2

Amplifier Harness

Fig. 5

1. Disconnect negative battery cable.

2. Remove the cover of the battery junction box. Fig. 1

3. Make sure supplied fuse is not installed in fuse holder and connect the subwoofer and amplifier

power wires to the studs pictured in figure 2. Either wire can go to either stud Torque to 4.7Nm

(42in-lb)

4. Route the power wires toward the firewall and secure with supplied wire ties.

5. Find the rubber grommet behind the battery and cut the end of the accessory tube. Feed the

power wires through the grommet tube into the cabin. Fig. 3

6. Install the white three pin power connectors on each power wire. Close the retainer.

Fig. 4

NOTE: Do not mix terminals from power wires between connectors. Make sure

all three wires from each power wire are each in a single connector.

7. Connect one power wire to the subwoofer

harness and one to the amplifier harness. Fig. 5

Fig. 1

Connect one power

harness to each

terminal

Fig. 2

Then

retainer

Insert terminals first.

Any wire can be in

any position.

Fig. 4

Fig. 3

8. If equipped with power seats, adjust the passenger seat as high as possible. Remove the panel

next to the seat. Fig. 6

9. Remove the front kick/sill trim panel as well as the rear sill panel. Fig. 7

10.Find the Audio Control Module (ACM) located above the right kickpanel area. Fig. 8 & 9

11.Disconnect the 28-pin gray connecter and connect it to the amplifier harness. To disconnect,

slide the white locking retainer out of the connector until it stops in order to press the connector

release tab. (Generic connector shown already disconnected from ACM for clarity). Fig. 10 & 11

Fig. 11

Fig. 6

Fig. 7

ACM Location

Fig. 9

ACM

Front of vehicle

Fig. 8

Fig. 10

Fig. 15

12.Connect the gray amplifier harness connector to

the ACM.

13.Disconnect the 28-pin black connector from the

ACM. Carefully cut away approximately 3 inches

of the black cloth wrapping the harness. Find

the green with black strip wire and cut. Strip

back about ¼inch of wire on each cut end.

Fig.12

See Splicing Technique section

14.Using the supplied butt connectors, connect the harness wire labeled, “connector”to the cut

wire attached to the ACM connector. Connect the harness wire labeled, “harness”to the other

cut wire. Fig. 13 & 14.

15.Connect the ground wires of both harness to the

ground point located in the right front kick panel

area. Fig. 15 Tighten to 7.5Nm (66in-lb)

16.Remove the four screws securing the front and

rear wire protector and route the subwoofer

harness alongside the factory harness securing

with supplied wire ties. Replace wire protectors.

Fig. 16

17.Remove the two 10mm nuts securing the jack

bracket. Fig. 17

18.Remove the jack tool bag.

Fig. 16

Fig. 17

Fig. 12

Fig. 13

Fig. 14

Fig. 18

NOTE: If equipped with the optional carpeted storage tray as pictured in Fig.

17, remove at this time. The storage tray cannot be used in conjunction with

the subwoofer. The subwoofer by design provides an optional storage area

once it is installed.

19.Remove the outer rear seat bolt on the driver’s

side. Fig. 18

20.Make cuts in the carpet according to the

measurement in Fig. 19. Only make cuts where

dotted lines shown.

21.Remove the rear seatback. See Second Row

Seat Removal Section.

22.Route subwoofer harness and the amplifier

from passenger’s side to driver’s side under

carpet. Subwoofer harness should be routed

behind seat brackets. Routing from one precut

opening to the next will aid in harness routing.

Fig. 20

1 inch

Fig. 19

Fig. 22

23.Route the black four pin subwoofer connector out of the hole that was cut near the stud where

the jack tools attach. Route the white amplifier connector behind seat bolts and out of the hole

that was cut near outer seat bolt. Fig. 21

24.Make wire harness connections to subwoofer and amplifier and set subwoofer in place aligning

brackets with the stud and seat bolt hole. Fig. 22

25.Reinstall the jack tool bag and nut.

NOTE: MAKE SURE WIRE HARNESS IS NOT BEING CRUSHED UNDER JACK

TOOL BAG!

26.Reinstall seat bolt. Torque to 109Nm (80ft/lb)

27.Mount the amplifier/bracket assembly over the studs on the back wall and secure with supplied

nuts. Torque to 4Nm (35in/lb) Fig. 23

NOTE: In rare instances, the upper mounting studs may be missing. If the

upper mounting studs are missing use the supplied self-drilling screws to

secure the top of the amplifier bracket. Fig. 24

28.Secure amplifier harness to back wall and connect to the amplifier.

29.Connect the two-pin connector of the amplifier to the two-pin connector of the subwoofer

harness. Fig. 23 (arrow)

Fig. 20

Fig. 21

Fig. 23

Fig. 24

30.Reinstall all previously removed parts in reverse order.

NOTE: MAKE SURE WIRE HARNESS IS NOT BEING CRUSHED WHEN

REINSTALLING JACK BRACKET!

31.Install supplied fuses into fuse holders.

32.Reconnect negative battery cable. Tighten to 7.5Nm (66in-lb)

SplicingTechnique

Use a sewing seam ripper, available from sewing supply stores, in order to cut open the harness in

order to avoid wire insulation damage.

Cut as little wire off the harness as possible. You may need the extra length of wire in order to change

the

location of a splice.

Strip approximately 5.0 mm (0.20 in) of insulation from each wire to be spliced.

Do not nick or cut any of the strands. Inspect the stripped wire for nicks or cut strands.

If the wire is damaged, repeat this procedure after removing the damaged section.

Select the red DuraSeal splice sleeve Part #

19168446 for 18-22 AWG wire

5. Place the DuraSeal splice sleeve in the crimp tool.

If using the EL-38125-10 splice sleeve crimping tool, use crimp nest number 2.

If using the

J-38125-8 splice sleeve crimping tool, use crimp nest number 1

6. Close the hand crimper handles slightly in order to firmly hold the DuraSeal splice sleeve in the

proper

nest.

Insert the wire into the splice sleeve barrel until the wire hits the barrel stop.

Tightly close the handles of the crimp tool until the crimper handles open when released.

The crimper handles will not open until you apply the proper amount of pressure to the DuraSeal

splice sleeve. Repeat steps7 and 8 for the opposite end of the splice.

Using the heat torch, apply heat to the crimped area of the barrel.

Start in the middle and gradually move the heat barrel to the open ends of the tubing:

The tubing will shrink completely as the heat is moved along the insulation.

A small amount of sealant will come out of the end of the tubing when sufficient shrinkage is

achieved.

Release Button

Seatback Removal

Removing O/B Head Restraints and CTR Head Rest.

Remove O/B head restraints by pushing in on two release buttons on head rest guide caps and lifting up on head

restraint (qty 2) Fig. 1 & 2

Remove CTR head rest by pushing in on two release buttons on head rest guide caps and lifting up on head rest (qty

1) Fig. 1 & 2

Removing Seat Back from Vehicle

Remove 6 Head rest guides from seat back/BIW by

inserting 90 degree awl into guide with front of awl

point facing forward, locate groove in guide plastic

(located on passenger or driver side of centerline of

guide and rotate awl 90 degrees then lift up on the awl

to pull guide free of seatback and BIW. Fig. 3 and Fig. 4

Fig. 1

Fig. 2

Fig. 3

Fold 60/40 cushions to upright position Fig. 5

Insert awl into groove in head rest guide, then

rotate 90 degrees and pull up on tool to pull

guide from BIW

Fig. 4

Fig. 5

Locate and remove 4 M6 lower attachment bolts securing the seat back to the BIW cab wall. Fig. 6

Using angled awl with point facing passenger side of vehicle – find latch release lever located to passenger side of

each child seat re-router loop below the seat back trim. Insert awl into release lever on latch and pull vertically up

10-20 mm while pulling seat back forward to disengage striker from latch (Qty 3 latches – Passenger, Driver and

Center) Release order does not matter Fig. 7, Fig. 8, Fig. 9. Fig. 10

Seat back can now be removed from the vehicle.

Remove M6 Lower attachment bolts – (Qty 4)

Fig. 6

Fig. 7

Inhaltsverzeichnis

Andere Kicker Subwoofer Handbücher

Kicker

Kicker KMW10 Bedienungsanleitung

Kicker

Kicker CompVR CVR10 Bedienungsanleitung

Kicker

Kicker Comp C10 Bedienungsanleitung

Kicker

Kicker CompVT CVT12 Bedienungsanleitung

Kicker

Kicker Solo-Baric S10L5 Bedienungsanleitung

Kicker

Kicker PSON13MY Bedienungsanleitung

Kicker

Kicker Q-CLASS CompQ10 Bedienungsanleitung

Kicker

Kicker Solo-Baric L5 Bedienungsanleitung

Kicker

Kicker SWRA207 Bedienungsanleitung

Kicker

Kicker PSON13 Bedienungsanleitung

Kicker

Kicker Solo-Baric L7 S15L7 Bedienungsanleitung

Kicker

Kicker CompS10 Bedienungsanleitung

Kicker

Kicker Q-CLASS CompQ12 Bedienungsanleitung

Kicker

Kicker SOLO CLASSIC S10C Bedienungsanleitung

Kicker

Kicker CompVR CVR10 Bedienungsanleitung

Kicker

Kicker TE Series Bedienungsanleitung

Kicker

Kicker SRAMCQ09 Bedienungsanleitung

Kicker

Kicker SWRA211 Bedienungsanleitung

Kicker

Kicker Soundgate SWRA406 Bedienungsanleitung

Kicker

Kicker Comp DC12 Bedienungsanleitung

Kicker

Kicker SOLO-BARIC DS12L3 Bedienungsanleitung

Kicker

Kicker SoundGate SWRA411 Bedienungsanleitung

Kicker

Kicker TCVT8 Bedienungsanleitung

Kicker

Kicker KICKER CompVT CVT10 Bedienungsanleitung

Beliebte Subwoofer Handbücher anderer Marken

Sony

Sony XS-AW8 Bedienungsanleitung

Sony

Sony XS-L836 Bedienungsanleitung

B&C Speakers

B&C Speakers 15 HPL 76W Bedienungsanleitung

Velodyne

Velodyne DD-18+ Bedienungsanleitung

Sonance

Sonance Cinema Series SUB 10-150 Bedienungsanleitung

Hifonics

Hifonics HW-12 Kurzanleitung

Magnat Audio

Magnat Audio ADR 130 BP Bedienungsanleitung

Blitz

Blitz BZP106 Bedienungsanleitung

Technics

Technics SB-AS500 Bedienungsanleitung

Lyngdorf

Lyngdorf BW-2 Bedienungsanleitung

Lyngdorf

Lyngdorf BW-3 Bedienungsanleitung

Pyle Pro

Pyle Pro PYLE PRO PDW15125 Bedienungsanleitung

REL Acoustics

REL Acoustics Q Series Bedienungsanleitung

Pioneer

Pioneer Elite S-W1EX Bedienungsanleitung

L-Acoustics

L-Acoustics KIVA SB15M Kurzanleitung

B&C Speakers

B&C Speakers Woofer 12 HPL 76 Bedienungsanleitung

KEF

KEF KUBE 200 Bedienungsanleitung

Yamaha

Yamaha SW500 Bedienungsanleitung