Kidde Fire Systems SmartOne K-76-227 Bedienungsanleitung

Effective: July 2021

K-76-227

SmartOne® Hand-held

Device Programmer

- For all generations of SmartOne devices

- For DS and KS series detectors

DESCRIPTION

The Hand-held Device Programmer provides a convenient

means to assign device address information and test device

operation. The Programmer is designed to support all

SmartOne intelligent and addressable devices, including DS/KS

Series Detectors. Programming adapters are provided in kit.

Note: Prior to using the Programmer, ensure that you have

the following accessories:

• SLC Interface Adapter

• AC Adapter (120V or 240V)

• AI/AO Module Programming Adapter for newer modules

• DS/KS Series Programming Adapter

• 4 NiMH Rechargeable AA Batteries

• Storage Case

MAIN MENU LEVEL SELECTIONS

To access Main Menu selections, press the <>and <>

buttons until the LCD display shows the desired selection, then

press <E>. There are four Main Menu selections:

•Single Addressing - Set an address for a single device at

a time.

•Sequential Addressing - Set an address range (with a

start address and end address), and give each device a

unique address within that range. Program multiple

devices quickly, and reduce the possibility of setting dupli-

cate addresses.

•Alarm Test - Test the alarm initiating responses of initiating

devices. A device that fails the Alarm Test should not be

installed.

•Options - Adjust LCD settings; show current firmware

version; adjust the Power-Off timer.

GENERAL MENU NAVIGATION

General menu navigation rules include the following keypad

instructions:

1. Press the <>and <>buttons to navigate the menu

levels.

2. Press <E> (Enter) to enter any sub-menu from any

higher level.

• Press the <>button to return to a previous menu.

FEATURES

• Single or sequential device addressing modes

• Compact design; user-friendly

• AC and battery power operation

• Adjustable LCD Contrast

• Integral detector base for older detectors

• Adapter Base for DS and KS Series Detectors included

• Adapter Base for AI and AO modules included

• SLC Interface Adapter Connector—no SLC wiring

• Less than 15 seconds addressing time per device

“ON”

Button

Status LED

“Charging”

LED

Keypad

Buttons

LCD

Display

- 2 -

CONNECTING TO VARIOUS SMARTONE DEVICES

Note: The power may be ON or OFF when connecting a SmartOne device to the Hand-held Programmer.

Older Generation Smoke/Heat Detectors

Snap the detector into the detector base, orient the index marker on the device to the five o’clock position, then rotate clockwise.

DS and KS Series Detectors

A fixture that allows the DS and KS Series Detectors to be programmed via the SmartOne Hand-held Programmer is

included with the programmer and also available separately (P/N 70-600000-110). The adapter is a base with an

attached wire and jack which plugs directly into the programmer. It does not mount onto the programmer. The detector

head is then attached to the connected base for programming. The following detector heads fit onto the fixture:

• DS-PS Intelligent Photoelectric Detector • KS-PS Intelligent Photoelectric Detector

• DS-HFS Intelligent Fixed Temperature Thermal Detector • KS-HD Intelligent Heat Detector

• KS-PHD Intelligent Combination Photoelectric Heat

Detector

Base

Smoke

Detector

Index

Marker

SLC Out Adapter

Connector

SLC Adapter

Jack Plug

DS or KS Series

Detector Head

DS/KS Series Detector

Programming Adapter

(P/N 70-600000-110)

NOTE:

Lay flat. Adapter does

not fit on programmer.

- 3 -

Older Generation Addressable Input (AI) and Addressable Output (AO) Modules

Connect the legacy AI/AO Module Adapter to the detector base and rotate clockwise. Insert the AI or AO module into the adapter

with the terminal block facing left. Tilt the module into the recess of the adapter such that the terminal block screws make contact

with the spring-loaded probes; then snap the back of the module into the right half of the recess.

New Generation Addressable Input (AI) and Addressable Output (AO) Modules

A fixture that allows new generation AI and AO modules to be programmed via the SmartOne Hand-held Programmer

is included with the programmer and also available separately (P/N 06-220493-001). The adapter is a base with a

printed circuit board which fits directly onto the DS/KS Series Detector Programming Adapter (which then plugs directly

into the SLC Out port of the programmer.) It does not mount onto the programmer. An AI or AO module snaps into

place on the assembly, oriented with the 4-pin terminals at the top and 6-pin terminals at the bottom. The following

modules fit onto the fixture:

• Class A/2B Addressable Input Module • Single Addressable Output Module

• Class B Addressable Input Module • Dual Addressable Output Module

AI/AO

Module

Adapter

Recess of AI/AO

Module Adapter

Spring-Loaded

Probes

AI/AO Module Programming Adapter

(P/N 06-220493-001)

AI or AO Module

SLC Out Adapter

Connector

SLC Adapter

Jack Plug

DS/KS Series Detector

Programming Adapter

(P/N 70-600000-110)

NOTE:

Lay flat. Adapter does

not fit on programmer.

Kidde Fire Systems

400 Main Street

Ashland, MA 01721

Ph: 508.881.2000

Fax: 508.881.8920

www.kiddefiresystems.com

SmartOne is a registered trademark of Kidde-Fenwal, Inc., or its parents, subsidiaries or affiliates.

This literature is provided for informational purposes only. KIDDE-FENWAL, INC. believes this data to be accurate, but it is published and presented without any

guarantee or warranty whatsoever. KIDDE-FENWAL, INC. assumes no responsibility for the product's suitability for a particular application. The fire suppression system

design, installation, maintenance, service and troubleshooting must be performed by trained, authorized Kidde Fire Systems distributors for the product to work correctly.

If you need more information on this product, or if you have a particular problem or question, contact:

KIDDE-FENWAL, INC., Ashland, MA 01721 USA, Telephone: (508) 881-2000.

K-76-227 Rev AC

EXPORT INFORMATION (USA)

Jurisdiction: EAR

Classification: EAR99

This document contains technical data subject to the EAR.

Other Devices

Plug the SLC Interface Adapter jack into the Programmer Con-

nector marked “SLC OUT.” Locate terminal blocks on device

labeled “SLC” or “PC Line.” Connect one SLC Interface Adapter

wire to Terminal “A” on the device, and the other wire to

Terminal “B.”

SUPPORTED DEVICES

* Newer modules

ORDERING INFORMATION

SmartOne Device Part No.

Ionization Detectors

70-402001-100

70-401001-000

70-401002-000

70-401004-000

Photoelectric Detectors

71-402001-100

71-401001-000

71-401002-000

71-401004-000

KS-PS

DS-PS

Duct Detector DS-SD

Heat Detector

KS-HD

DS-HFS

70-404001-100

Combination Photo /Heat Detector KS-PHD

Addressable Contact Input Devices

70-417008-001

70-417018-001

70-417008-002

70-407008-001

70-407018-001

70-610001-001 *

70-620001-001 *

70-407008-002

Addressable Contact Output Devices 70-408004-001

70-518004-001 *

70-528004-001 *

70-408014-001

Addressable Signal/Sounder Module 70-200200-001

70-200200-002

Addressable AlarmLine Module 73-100001-003

Remote Releasing Module 70-600000-001

70-600000-002

Class A Power Module 70-210210-100

Part No. Description

70-600000-100 SmartOne Hand-held Device

Programmer (complete unit)

Contents include the following:

• SLC Interface Adapter

• AC Adapter (120/240V)

• AI/AO Module Adapter

(for newer modules)

• 4 NiMH Rechargeable

AA Batteries

• Storage Case

• Includes one (1) DS/KS Series

Detector Programming Adapter

70-600000-101 SmartOne Hand-held Device

Programmer—

only with SLC Interface Adapter

and Quick Reference Guide.

(Does NOT include other

Adapters, Batteries, or Storage

Case.)

06-220197-001 Accessory Kit—contents include the

following:

• SLC Interface Adapter

• AC Adapter (120/240V)

• AI/AO Module Adapter

(for newer modules)

70-600000-110 DS/KS Series Detector Programming

Adapter

06-220493-001 AI/AO Module Programming Adapter

(for newer modules)

Andere Kidde Fire Systems Hauptplatine Handbücher

Kidde Fire Systems

Kidde Fire Systems SmartOne K-76-227 Bedienungsanleitung

Beliebte Hauptplatine Handbücher anderer Marken

DFI

DFI SD170 Bedienungsanleitung

ASROCK

ASROCK ROMED8-2T Bedienungsanleitung

Asus

Asus P2L97A Bedienungsanleitung

Winmate

Winmate IC70 Bedienungsanleitung

Asus

Asus MES-B Bedienungsanleitung

Grantech

Grantech SYS8F377VGGA-3OMN Bedienungsanleitung

Telit Wireless Solutions

Telit Wireless Solutions SL869-3DR Bedienungsanleitung

Gigabyte

Gigabyte GA-9IVDT Bedienungsanleitung

Texas Instruments

Texas Instruments ADS8372EVM Bedienungsanleitung

Commell

Commell MS-C73 Bedienungsanleitung

IBT Technologies

IBT Technologies MB860 Bedienungsanleitung

Nvidia

Nvidia TEGRA DG-04927-001_V01 Bedienungsanleitung

Biostar

Biostar M7VIT Bravo Bedienungs- und Montageanleitung

Intel

Intel D33217CK Bedienungsanleitung

Asus

Asus F1A55-M LX PLUS R2.0 Bedienungsanleitung

EPC

EPC EPC9147C Bedienungsanleitung

Asus

Asus EX-B760M-V5 D4 Bedienungsanleitung

EPOX

EPOX MU-8KHA0010 Bedienungsanleitung