Kinco F7 Einrichtungshandbuch
1.1 Environmental Requirement
Please make sure that AC power,PLC output modules,starters,relays and other types of
electrical interface device are far away from the back of this product.
1.2 Power Requirement
Input voltage: 18~28VDC;
Particularly note that there must be enough distance between this product and
converters or switch mode power supply. Make sure that the input and output cables
of that kind equipment are shield cable and the shielding network is connected with the
ground.
Make sure that the DC power and AC power is isolated.
Do not use common power with perceptual load or input circuit of the controller.
An Internal fuse will prevent damage for over voltage condition, however it
isn’t guaranteed the internal electronic components are not damaged.
Chassis ground must be used.
2.1 Installation Instructions
It uses bracket installation which is compatible with VESA standard.The
4 installation holes for F7 is 75mm*75mm,and for F10 is 100mm*100mm,the
installation holes distance is as shown in chapter 2.2.
2.2 Dimensional Drawing (mm)
F7/F10
Human Machine Interface
Installation Instruction
Kinco Electric (Shenzhen) Ltd.
Tel：0755-26585555
Fax：0755-26616372
Web: www.kinco.cn Email：sales@kinco.cn
Kinco WeChat Add: Building 1, No. 6 Langshan 1st Rd, Hi-tech Park
North, Nanshan,Shenzhen,China.
http：//www.kinco.cn Email：sales@kinco.cn
1.Installation Note
2.Installation Description
2.3 Power Connection
Before connecting the power, please make sure all local and national electrical
standards are met. For power cables, please select cables with these specifications:
overall diameter 6.--8.3mm, 7 cable cores,the internal cable cores should be 22AWG or
above.The power cable is welded to WF-16 connector.The definition of the WF-16
connector is as shown in chapter 3.1.In the picture,24V_PWER is connected to
DC24V,and 24V_GND is connected to 0V.
3.1 Power Supply&Serial Port
The power supply and serial port use the same connector,as shown in
following picture.
Note:There are two communication ports.One is COM0,it supports RS485.The
other one is COM2 which is used for RS232 communication and downloading
project.
3.2 USB HOST
This interface is mainly used for importing initial LOGO,user’s configuration uploading/
downloading,recipe data import/export and historical data export.
4.1 Instructions for entering Operation Mode selection window
Press and hold the touch panel before power on HMI,then power on
HMI.Release your help after HMI enter operation mode selection window,then
select the operation mode.If no any operation in 20s after entering
operation mode selection window,HMI will enter application mode
automatically.
3.External Interface
4.Operation Mode
F7
F10
4.2 Descriptions of functions in Operation Mode selection window
After entering operation mode selection window,it will popup a
menu.Follows are the descriptions of the functions in the menu:
System Setup：Press this button to enter system setup window.This
window is used to set initial window,screen saver time,buzzer and
brightness adjustment.After setting,press Restart button to restart HMI.
Firmware Update：Press this button to enter firmware update window.This
window is used to update firmware.Normally this mode is not advised to
use without guiding by manufacturer.
Touch Calibration：Press this button to enter touch calibration window.It
will restart HMI automatically after calibration successful.There is a
timer in this button,it will enter application window if there is no
operation within 20s.
Stop timer: Press this button to stop the 20s timer.
Note:There is a multi-languages button,it is used to switch the English
and Chinese.
Dieses Handbuch passt für folgende Modelle
1
Inhaltsverzeichnis
Andere Kinco Aufnahmegeräte Handbücher
Beliebte Aufnahmegeräte Handbücher anderer Marken
Strymon
Strymon NIGHTSKY Bedienungsanleitung
Mitsubishi Electric
Mitsubishi Electric 16CH DIGITAL RECORDER DX-TL5000U Bedienungsanleitung
Tews Technologies
Tews Technologies TPMC465 Bedienungsanleitung
Honeywell
Honeywell Excel 50 Bedienungsanleitung
SeaLevel
SeaLevel COMM+8.LPCI Bedienungsanleitung
Arturia
Arturia AUDIOFUSE STUDIO Bedienungsanleitung
